Related Manuals for Taiden HPA-350/02
Summary of Contents for Taiden HPA-350/02
- Page 1 Digital Audio Power Amplifier Professional Audio Power Amplifier Installation and Operation Manual V 1.0...
-
Page 2: Table Of Contents
Contents Important Safety Instructions ...................... II Chapter 1 Overview ........................1 Chapter 2 Functions and indications ..................2 Chapter 3 Connection and operation ..................4 3.1 Input/Output ..............................4 3.2 Stereo mode ..............................4 3.3 Bridge mode ..............................5 3.4 Mono mode ............................... 6 3.5 Operating instructions ............................ - Page 3 To protect your hearing, avoid high pressure level on earphones. Adjust to a lower and convenient level. If any detailed information is needed, please contact your local agent or TAIDEN service center in your region. Any feedback, advice and suggestion about the products is appreciated TAIDEN is the registered trademark of TAIDEN Co., Ltd.
-
Page 4: Important Safety Instructions
Service Center. The MAINS plug serving as a disconnection device, 20. All TAIDEN products are guaranteed for definite time (see the WARRANTY CARD for details) excluding the should be easy to operate. The apparatus should be connected to the MAINS... - Page 5 Important Safety Instructions The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: To reduce the risk of fire or electric shock, DO NOT expose units to rain or moisture.
- Page 6 Digital Audio Power Amplifier. Chapter 4：Specifications Main technical parameters of Digital Audio Power Amplifier. This manual is applicable to: HPA-350/02 Digital Audio Power Amplifier (2 channels, 8Ω, 350 W) HPA-350/04 Digital Audio Power Amplifier (4 channels, 8Ω, 350 W) HPA-450/02 Digital Audio Power Amplifier (2 channels, 8Ω, 450 W)
-
Page 7: Chapter 1 Overview
Chapter 1 Overview Digital audio power amplifier (hereinafter referred to as "PA") adopts the high efficiency class D power amplifier and switching mode power supply technology, the efficiency under conventional conditions is more than 80%. PA adopts active power factor correction technology, can adapt to all the global supply network, and plug &... -
Page 8: Chapter 2 Functions And Indications
Chapter 2 Functions and indications Front panel of HPA-350/02 and HPA-450/02 Front panel of HPA-350/04 and HPA-450/04 Rear panel of HPA-350/02 and HPA-450/02 Rear panel of HPA-350/04 and HPA-450/04 Digital audio power amplifier Figure 2.1 1. Clip indicator disconnect the load, reduce the gain greatly; if the ... - Page 9 When the "Fault" indicator is turned on, in order to provide protection, the output is blocked, and PA cannot output any sound from the loudspeaker; The "Fault" indicator is on when the heat sinking is overheating or PA detects a DC voltage; ...
-
Page 10: Chapter 3 Connection And Operation
Chapter 3 Connection and operation 3.1 Input/Output Connecting knowledge: Input wire use the shielded wire with high shielding layer density; Input signal use balanced connection, to reduce noise interference; If using unbalanced connection, the shorter Connection diagram: balanced analog input and AES3 the better, had better not exceed 3 meters;... -
Page 11: Bridge Mode
3.3 Bridge mode... -
Page 12: Mono Mode
3.4 Mono mode... -
Page 13: Operating Instructions
3.5 Operating instructions Please confirm before installation: signal and 75 Hz for microphone signal. For each The power cord not connected to the power mixer input channel, the filter frequency is set socket; below the minimum fundamental frequency of the ... -
Page 14: Heat Sinking
When PA is switched on, the output interface may have a fatal voltage. Note: TAIDEN is not responsible for any damage caused by excessive use of other system components. 3.5.3 Heat sinking Heat sinking method: Cold air intake from front panel vent, flow through the heat sink and take away heat, and discharge from rear panel. -
Page 15: Troubleshooting
3.6 Troubleshooting The following table lists the main reasons for the abnormal work and treatment measures, as well as the circuit protection in each case. Phenomenon Possible cause Treatment measures PA is not connected to AC power Check AC cable network The power plug is not inserted into the "Power"... -
Page 16: Chapter 4 Specifications
Chapter 4 Specifications HPA-350/02 HPA-450/02 HPA-350/04 HPA-450/04 8 Ω/Stereo 8 Ω/Stereo 2×350 W 2×450 W 4×350 W 4×450 W 4 Ω/Stereo 4 Ω/Stereo 2×595 W 2×765 W 4×595 W 4×765 W Rated power 16 Ω/Bridge 16 Ω/Bridge 1×700 W 1×900 W 2×700 W... - Page 17 TAIDEN INDUSTRIAL CO., LTD. 6/F, Block B, Future Plaza, 6060 Qiaoxiang Rd, Nanshan District, Shenzhen, China Copyright by TAIDEN P.C.: 518053 Last Revision: 10/2017 Website: http://www.taiden.com...