Page 1
My Café Tea & Coffee Pod Brewer The Bunn logo is a registered trademark of Bunn-O-Matic Corporation. My Café is a trademark of Bunn-O-Matic Corporation. RECORD MODEL & SERIAL NUMBER In order to receive accurate and timely warranty assistance, it is important to record the Model and Serial Number information located on the bottom of the brewer.
INSPECTING THE SPRAYHEAD/SEAL...17 CLEANING THE POD HOLDER ...17 CYCLING THE BREWER ...17 STORING THE BREWER...17 TROUBLESHOOTING ...18 BUNN REPLACEMENT PARTS ...22 LIMITED WARRANTY ...23 WARNING RISK OF FIRE OR ELECTRICAL SHOCK This symbol alerts you This symbol alerts you to Hazardous Voltage! to the risk of fire or...
Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices on the equipment should be kept in good condition. Replace any unreadable or damaged labels by visiting our web site at www.bunn.com. # 37267.0000 The BUNN ®...
Follow these basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and/or personal injury: • Read all instructions. • Do not touch hot surfaces. Use handles or knobs. • To protect against electric shock, do not place cord, plug, or brewer in water or liquid.
Improper installation could result in permanent damage and void the limited warranty. Read & follow instructions on page 9 or 10. • Use CAUTION when dispensing hot water from the brewer. The water from your BUNN Pod brewer is approximately 93°C (200°F). This is approximately 10°C (50°F) hotter than the hot water from your faucet and must be handled with care.
FEATURES & CONTROLS WATER RESERVOIR POWER SWITCH WATER INLET BLUE (BREW) LIGHTS CONTROL PANEL REFILL WATER INDICATOR COFFEE BREW BUTTON* * The Coffee or Tea button can be pressed again to stop or cancel a brew cycle in process. FIG 1. Exploded View HEATING INDICATOR FIG 2.
BUNN name. This light will go out during a brew cycle and when the brewer has gone into Sleep Mode. (Refer to the “Features” section on page 8 for more information.)
flavor. The “On-Off-On” water flow is normal. Always wait for the blue (brew) lights to go out, and the red BUNN light to come back on before carefully removing the mug or pod holder. Pressing either brew button during this operation will stop the brew cycle.
The My Café Automatic Pod Brewer is designed for businesses and office ™ applications, where a pressurized water system can be utilized to feed the brewer with a constant water supply. If the machine will not be used with plumbing, proceed to the “Pour-Over”...
For pour-over set-up, go to “Pour-Over Section” on page 12. 1. Remove the lid and water reservoir. (CAUTION: Do not place the brewer in a sink or other water source.) 2. Thoroughly rinse the water reservoir. 3. Replace the reservoir and lid and close the slide lid.
P2904 hold the pod holder release button while sliding the pod holder out. (NOTE: The red BUNN light will come back on indicating the brew cycle has finished.) P2908 8. Dispose of the used pod. Do Not Touch Hot Pod! P2909 (NOTE: Use care not to dispose of pod insert.)
“POUR-OVER SECTION” For Automatic set-up, go to “Automatic Section” on page 10. 1. Remove the lid and water reservoir. (CAUTION: Do not place the brewer in a sink or other water source.) 2. Thoroughly rinse the water reservoir. 3. Fill the reservoir to the maximum line with fresh cold water.
P2952 the pod holder release button while sliding the pod holder out. (NOTE: The red BUNN light will come back on indicating the brew cycle has finished.) 11. Dispose of the used pod. Do Not Touch Hot P2904 Pod! (NOTE: Use care not to dispose of pod insert.)
Brewing delicious coffee is similar to cooking any favorite food. Both require a good recipe. Proper coffee making requires quality equipment to precisely control water temperature, volume, and brew time. The BUNN assures consistency in your recipe by controlling all of these elements. The only variables remaining in the recipe are the amount of coffee and the volume of hot water used to extract the desired flavor.
URNEX Activated Descaler or JavaClean2 Cleaner and Descaler, available on our web ® site: www.bunn.com. (White vinegar can be used to descale if a descaling product is not available.) Follow the directions as printed on the manufacturer’s package. Fill the reservoir with descaling product as described by the manufacturer’s directions, or 946 ml (32 oz.) of white vinegar.
When the cycle has finished, empty the container. Repeat step 7 at least two more times to remove the solution from the tank. Clean the pod holder with a mild detergent and rinse thoroughly. 10) Proceed to the “Cleaning The Sprayhead/Seal” section. CLEANING THE SPRAYHEAD/SEAL Press the Power Switch into the off “O”...
CAUTION: The seal confines the hot liquid to the pod holder. Replace the seal if it becomes damaged. Parts are available at www.bunn.com. CLEANING THE POD HOLDER To prevent residue build up, it is a good idea to periodically disassemble the pod holder/screen assembly and clean it with a mild detergent.
Check to make sure the brewer is plugged in and the POWER SWITCH has been turned on. (The POD HOLDER RELEASE BUTTON - also known as the BUNN Indicator - will be illuminating red, indicating power to the brewer.) The HEATING INDICATOR is lit.
Page 19
SITUATION The REFILL WATER INDICATOR has come on. The POD HOLDER INDICATOR has come on. The water shuts off and comes back on again when brewing. EXPLANATION Pour-Over only: The WATER RESERVOIR has run low on water. Slide the lid open and pour additional water into the reservoir, or remove the reservoir and fill it at a sink, or other water source.
Page 20
TROUBLESHOOTING (Cont.) SITUATION (Continued) The water shuts off and comes back on again when brewing. The Pod Holder will not come out of the brewer. Water is appearing on the counter around the base of the brewer. Water leaks out around the sprayhead.
Page 21
® POD HOLDER RELEASE BUTTON) is lit, this indicates that the power to the machine is on. No action is required. The BUNN brewer is ready to brew. When the brewer enters a sleep mode the POD HOLDER BUTTON will not be glowing.
flavor extraction. SPRAYHEAD SEAL Used to seal the sprayhead area and ensure proper pod pressure and flavor extraction. To purchase replacement parts, visit our web site at www.bunn.com REPLACEMENT PARTS ® P2915 Holds 1.7 L (46 oz.) of fresh water for quick brewing.
(at our exclusive option) either (1) arrange for the unit to be repaired, at no cost to you for parts or labor, by a Bunn Authorized Service Representative, (2) replace the unit at no charge to you or (3) refund the purchase price you paid for the unit.
Need help?
Do you have a question about the MCAA and is the answer not in the manual?
Questions and answers