Subscribe to Our Youtube Channel
Related Manuals for ThermoSphere HTB-SR-400
Summary of Contents for ThermoSphere HTB-SR-400
- Page 1 INSTALLATION GUIDE TOWEL BAR HEATING | WALL TOWEL BARS Excellence in heating solutions.
-
Page 2: Table Of Contents
Contents What‘s in the box? ..........3 Before you start ............. 4 Installing Towel bars ..........5 Wiring diagram ............. 7 Installation diagram ..........12 Retrofit on existing tiles ........13 Technical data ............. 15 Contact information ..........18... -
Page 3: What's In The Box
What‘s in the box? Check you‘ve got everything: • ThermoSphere towel bar • Dress ring • Connection wire (2m) • Mounting spigot and 2 fixing screws • Allen key and 2 grub screws • 4.5mm drill bit You will also need: •... -
Page 4: Before You Start
Before you start ThermoSphere towel bars should be: • Installed on an RCD protected circuit • Connected to a suitably rated 12V transformer • Installed by a qualified professional electrician, in line with current electrical regulations and local standards. (For the UK: IEE 17th Edition Part P) •... -
Page 5: Installing Towel Bars
Installing Towel bars 1. Switch off mains power You will be installing the Towel bar as part of a high voltage mains CAUTION High Voltage electrical circuit. To ensure your Cables safety and to protect the Towel bar, switch off the mains power before you start the installation. - Page 6 Installing Towel bars 2. Choose a location Decide where the Towel bar is to be fixed to the wall and drill into the wall taking care to avoid any existing pipe work or electric cables. The 2m connection cable can then be fed through a conduit in the wall cavity or chased into a channel cut into a solid wall.
-
Page 7: Wiring Diagram
Installing Towel bars 3. Electrical connections Ensure the electricity is switched off. Connect the 12V transformer and towel bar to the electrical supply as shown in the diagram. Multiple bars should be wired in parallel. 4. Wiring diagram Switch / Thermostat Max. - Page 8 Carefully drill fixing holes, insert suitable wall pugs and fix the spigot in place with the screws provided. Installing multiple rails? Use the ThermoSphere mounting system (TBMS- 1000) and consult the relevant installation guide.
- Page 9 Installing Towel bars 6. Tile the wall At this stage the wall should be tiled. The mounting spigot is designed to be encapsulated within the tile adhesive layer. Cut the tile or use a 24mm tile drill bit to make a hole for the mounting spigot.
- Page 10 Installing Towel bars 7. Connection clips When the tile adhesive is set and the tiles have been grouted, the towel bar can be fixed in position. The optional dress ring should be installed and then the electrical clips can be connected by any competent individual.
- Page 11 Installing Thermorail 8. Fix Towel bar in position Remove the grub screw from the towel bar and locate over the spigot, ensuring the bar is level. Mark the position of the grub screw holes hole on the spigot. Drill the spigot using the 4.5mm bit. Fix the towel bar in position by tightening the grub screw so that it locates into the 4.5mm hole, with the allen key provided.
-
Page 12: Installation Diagram
Installation diagram PLAN VIEW Tile over the mounting spigot 1. Wall 5. Dress ring (optional) 2. Suitable wall plug 6. Connection clip 3. Fixing screw 7. Grub screw 4. Mounting spigot 8. Towel bar... -
Page 13: Retrofit On Existing Tiles
Retrofit installation 8. Retrofit over existing tiles 1. Drill the wall in desired location to allow for 4 fixings and feeding the cable into the wall cavity. 2. Feed connection cable into the wall and make electrical connections in line with the diagram on page 7. - Page 14 Retrofit installation 8. Retrofit over existing tiles (continued) 5. Drill the spigot using the supplied 4.5mm bit. Take care to protect the cables from the drill! 6. Connect the connection clips and slide the towel bar over the mounting spigot. 7.
-
Page 15: Technical Data
Technical information HTB-SR-400 L400 x H32 x D100 HTB-SR-600 L600 x H32 x D100 HTB-SS-400 L400 x H32 x D100 HTB-SS-600 L600 x H32 x D100 Supply voltage 230V 50/60Hz Transformer voltage Warranty 5 years... - Page 16 Notes...
- Page 17 Notes...
-
Page 18: Contact Information
Thermogroup Ltd hello@thermosphere.com www.thermosphere.com E&OE © Thermogroup Ltd 2019...
Need help?
Do you have a question about the HTB-SR-400 and is the answer not in the manual?
Questions and answers