TABLE OF CONTENTS SERVICE SAFETY PRECAUTIONS ........................... 3 HANDLING THE LCD MODULE ............................SERVICE MODE ................................. LOCATION OF CONTROLS............................... 11 LAYOUT OF MAJOR BOARDS ............................15 MECHANICAL DISASSEMBLY............................16 WIRING CONNECTIONS ..............................29 EXPLODED VIEW ................................35 PACKING DISASSEMBLY ..............................39 CHASSIS AND CABINET REPLACEMENT PARTS LIST ....................
SERVICE SAFETY PRECAUTIONS • The caution items shown here describe major safety issues and should always be observed. • The meanings of the various indications are as follows. Indicates a hypothetical situation in which service personnel and nearby third parties, or even WARNING end users due to a product defect after the service operation is completed, could possibly be in danger of injury or even death in the event of operational error.
Page 4
WARNING • Always advise users to keep children away. There is danger of injury to children from tools, disassembled products, etc. KEEP CHILDREN AWAY • Always disconnect the power plug before starting work whenever power is not required. Failure to disconnect the power plug before starting work can result in electrical shock. UNPULUG •...
HANDLING THE LCD MODULE Safety Precautions 3. If the panel surface becomes soiled, wipe with cotton or a In the event that the screen is damaged or the liquid crystal soft cloth. If this does not remove the soiling, breathe on (fluid) leaks, do not breathe in or drink this fluid.
Page 6
7. Do not expose the LCD module to direct sunlight or strong 9. Do not disassemble the LCD module. Such actions could ultraviolet rays for an extended period of time. result in improper operation. 8. Do not store the LCD module below the temperature con- ditions described in the specifications.
SERVICE MODE 1. ENTERING TO SERVICE MODE 3. SERVICE ADJUSTMENT (1) Procedures (1) ADJUSTMENT MENU INDICATION ON/OFF : 1) Press MUTE key of remote hand unit to indicate MUTE MENU key(on TV set) on screen. 2) Press again MUTE key of remote hand unit to keep (2) During display of adjustment menu,the followings are pressing until the next procedure.
Page 8
4. FAILURE DIAGNOSIS PROCEDURE This model is equipped with self diagnosis function inside for trouble shooting. 4-1.Contents to be Confirmed by Customer Table 2 Contents of self diagnosis Display items and actual operation Set Power does not turn on by power-key, or it turns off Power indicator lamp blinks and picture does not come.
Page 9
4-2. Contents to be Confirmed in Service Work (Check in Self Diagnosis Mode) Table 3 Contents of self diagnosis Display items and actual operation Contents of self diagnosis Display items and actual operation B. Indication of part code of microprocessor.(QA01) * Please see item.4-4 C.
Page 10
4-4. Self Diagnosis Function Indication & Contents <Example of screen display> SELF CHECK 23000XXX TIME POWER : 000 BusCont : OK Block : UV V1 V2 V3 V4 Fig. 1 Table 4 Item Contents Instruction of results Indication of part code of microprocessor. B) Part code (QA01) C) TIME...
LOCATION OF CONTROLS Front TV front view On-timer indicator (green) Power indicator (red) Remote sensor Power switch – 11 –...
Page 12
Back Back view MONITOR OUT [40] (Audio/Video output) TV back view WOOFER OUT AUDIO OUT (Fixed/Variable) EXT4 IN/OUT (Scart 4) Cable holder EXT5 IN/OUT (Scart 5) EXT3 IN/OUT (Scart 3) Cable holder Back view Back view Side view EXT6 IN (S-video/ EXT1 IN Video/Audio...
Page 13
Sound mute VCR : To control VCR DVD : To control DVD When in VCR or DVD mode: When in TV (Teletext) mode: (Only for Toshiba VCR/DVD To reveal concealed text players) To hold a wanted page to PAUSE To enlarge teletext display size...
MECHANICAL DISASSEMBLY • Note: Be sure to lay down the main body (by placing its screen downward) for disassembly. Removing the back cover 1) Remove the BC stand cover. 2) Remove the BC terminal cover. 3) Remove 6 screws, then remove the stand. BC Stand cover Stand BC Terminal cover...
Page 18
Removing the speakers 1) Remove the back cover. (Refer to Item 1.) 2) Disconnect the speaker wire harness on the Front/AV board. 3) Remove the wire harness of the 3 wire holders. 4) Remove 4 screws, then remove the left speaker and wire holder. 5) Remove 4 screws, then remove the right speaker and wire holder.
Page 19
Removing the top shield bracket 1) Remove the back cover. (Refer to Item 1.) 2) Remove 5 screws, then remove the top shield bracket. Top shield bracket STP 3x8 STP 3x8 – 19 –...
Page 20
Removing the Power Module unit 1) Remove the back cover. (Refer to Item 1.) 2) Disconnect the power cord from the connector. 3) Remove the 3 wire harnesses from the 3 wire clampers on the plate back R. 4) Disconnect the 8 wire harnesses from the 8 connectors on the Power Module unit. 5) Remove 7 screws, then remove the Power Module unit.
Page 21
Removing the Scaler board 1) Remove the back cover. (Refer to Item 1.) 2) Remove the top shield bracket. (Refer to Item 3.) 3) Remove 4 screws (STP3x6) and 2 screws (STP3x5), then remove the top shield RM. 4) Disconnect the 8 wire harnesses and 2 FFC from the Scaler board. 5) Remove 4 screws (STP3x5), then remove the Scaler board and bottom shield RM.
Page 22
Removing the D-Rewrite board 1) Remove the back cover. (Refer to Item 1.) 2) Remove the top shield bracket. (Refer to Item 3.) 3) Remove the Scaler board. (Refer to Item 5.) 4) Remove 2 screws, then remove the D-Rewrite board. 5) Disconnect the 2 wire harnesses and 1 FFC on the D-Rewrite board.
Page 23
Removing the back terminal plate, back bottom plate and back R plate 1) Remove the back cover. (Refer to Item 1.) 2) Remove the top shield bracket. (Refer to Item 3.) 3) Remove the Scaler board. (Refer to Item 5.) 4) Remove the D-Rewrite board.
Page 24
Removing the TN/AOUT, AV2 and Signal boards 1) Remove the back cover. (Refer to Item 1.) 2) Remove the top shield bracket. (Refer to Item 3.) 3) Remove the Scaler board. (Refer to Item 5.) 4) Remove the D-Rewrite board. (Refer to Item 6.) 5) Remove the back plates.
Page 25
Removing the Front /AV board 1) Remove the back cover. (Refer to Item 1.) 2) Remove 1 screw (BIDT2 3x10 BZ). 3) Remove 2 screws (PP 3x6), then remove the front AV panel. 4) Remove 1 screw (BIDT2 3x10 BZ) and 1 screw (PP 3x6), then remove the rear AV panel. 5) Disconnect the 2 wire harnesses and 1 FFC from the Front/AV board.
Page 26
10. Removing the Power SW and LED/RMT boards 1) Remove the back cover. (Refer to Item 1.) 2) Remove 3 screws (STP 3x8), then remove the LED/RMT board. 3) Disconnect the 2 wire harnesses from the connector on the LED/RMT board. 4) Remove 2 screws (PP 3x6), then remove the cord holder.
Page 27
11. Removing the chassis frame 1) Remove the back cover. (Refer to Item 1.) 2) Remove the speakers. (Refer to Item 2.) 3) Remove the top shield bracket. (Refer to Item 3.) 4) Remove Power Module unit. (Refer to Item 4.) 5) Remove the Scaler board.
Page 28
12. Removing the LCD and front bezel cover assembly 1) Remove the back cover. (Refer to Item 1.) 2) Remove the speakers. (Refer to Item 2.) 3) Remove the top shield bracket. (Refer to Item 3.) 4) Remove Power Module unit. (Refer to Item 4.) 5) Remove the Scaler board.
Parts No. Description LOCATION No. Parts No. Description A701A 23067683 CARTON, TOP CASE Y101C 23566311 OWNERS MANUAL, DEUT G LCD (FOR 32WL46B) (FOR 32WL46G) 23067684 CARTON, TOP CASE Y101D 23566312 OWNERS MANUAL, S LCD (FOR 32WL46G) (FOR 32WL46G) A701B 23067688...
· · · · · The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. · · · · · The PC board assembly with mark is no longer available after the end of the production. Model : 32WL46B/32WL46G Capacitors ..... CD : Ceramic Disk PF : Plastic Film EL : Electrolytic Resistors ....
Page 42
Location Parts No. Description Location Parts No. Description C4222 24092538 CERAMIC CHIP, 10V F 1UF Z CD16 24109333 CERAMIC CHIP CK73B 25V 33000PFK C4311 24100104 CERAMIC CHIP, 25V F 0.1UF Z CD18 24109332 CERAMIC CHIP, 50V B 3300PF K C4312 24100104 CERAMIC CHIP, 25V F 0.1UF Z CD20 24092726 CERAMIC CHIP CK733B 16V 2,200,000PFK...
Page 43
Location Parts No. Description Location Parts No. Description CV52 24203100 ELECTORLYTIC, 16V 10UF M 7L 3A CZ37 24100104 CERAMIC CHIP, 25V F 0.1UF Z CV53 24092538 CERAMIC CHIP, 10V F 1UF Z CZ38 24100104 CERAMIC CHIP, 25V F 0.1UF Z CV54 24092538 CERAMIC CHIP, 10V F 1UF Z CZ39...
Page 44
Location Parts No. Description Location Parts No. Description R520 24366681 CARBON FILM, 1/6W 680 OHM J RA08 24011101 CHIP, METAL FILM, 1/20W 100 OHM J R523 24011103 CHIP, METAL FILM, 1/20W 10K OHM J RA09 24011102 CHIP, METAL FILM, 1/20W 1K OHM J R524 24011103 CHIP, METAL FILM, 1/20W 10K OHM J RA10...
Page 45
Location Parts No. Description Location Parts No. Description RB15 24011470 CHIP, METAL FILM, 1/20W 47 OHM J RS15 24011104 CHIP, METAL FILM, 1/20W 100K OHM J RB32 24011105 CHIP, METAL FILM, 1/20W 1M OHM J RS16 24011104 CHIP, METAL FILM, 1/20W 100K OHM J RB33 24011123 CHIP, METAL FILM, 1/20W 12K OHM J RS17...
Page 46
Location Parts No. Description Location Parts No. Description RS97 24011223 CHIP, METAL FILM, 1/20W 22K OHM J RV65 24552101 OXIDE METAL FILM, 1/2W 100 OHM J RS99 24011101 CHIP, METAL FILM, 1/20W 100 OHM J RV67 24872471 CHIP, 1/16W 470 OHM J RS103 24011103 CHIP, METAL FILM, 1/20W 10K OHM J RV68...
Page 60
CIRCUIT BLOCK DIAGRAM Q610 TA2024 A-OUT SPEAKERS Q630 LA4525 HP-AMP H001 TADF-003A H002 MPSN11B/11 QS102 QS103 UPD64084GC QD05 NJM2150V 3DYCS QV01 CXA2069Q W-OUT TDA9181T TA1274AF EXT-1 AV-SW 128M DDR_SDRAM Cr or R COMB EXT-2 MST9883-C or G Filter 3ch-A/D Cb or B EXT-3 OUT1 A_in...
Page 61
SCHEMATIC DIAGRAM MODEL : 32WL46B/32WL46G WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
SPECIFICATIONS MODEL 32WL46B 32WL46G Power source 110 - 240V AC, 50/60 Hz Power consumption 175 W, 1.0 W (standby) 819 mm (W) x 645 mm (H) x 308 mm (D) Dimensions Mass (Weight) *** kg Stereo Nicam/MPX Speakers 60 x 120 mm 2 pcs.