Related Manuals for Robur TS 2000
Summary of Contents for Robur TS 2000
- Page 1 Installation, use and maintenance manual TS 2000 individual natural gas/LPG natural draught gas-fired convectors...
- Page 2 The rights of those who have legitimately filed the registered trademarks contained within this publication are not affected. With the aim of continuously improving the quality of its products, Robur S.p.A. reserves the right to modify the data and contents of this Installation, use and maintenance manual without prior notice.
-
Page 3: Table Of Contents
Handling ..............p. 8 Cleaning and maintenance ......p. 16 Appliance positioning ........p. 8 Any malfunctions of operation ..... p. 16 Minimum clearance distances ......p. 9 7 Appendices ................p. 17 ErP technical sheet ..........p. 17 Installation, use and maintenance manual – TS 2000... -
Page 4: Iintroduction
RECIPIENTS Installation, use and maintenance manual This Manual is intended for: This Manual is an integral part of the TS 2000 appli- End user, for appropriate and safe use of the appliance. ▶ ance and must be handed to the end user together Qualified installer, for correct appliance installation. -
Page 5: Iii.2 Compliance
EU directives and standards Burn hazard The TS 2000 series gas-fired convectors are certified in accordance with European regulation GAR 426/2016/ The appliance contains very hot parts. EU and meet the essential requirements of the following „... - Page 6 Warnings „ Incorrect installation. „ Damages caused by external agents such as salts, „ Misuse. chlorine, sulphur or other chemical substances „ Failure to comply with the manufacturer's indica- present in the air of the installation site. tions on installation, use and maintenance. „...
-
Page 7: Features And Technical Data
(set on the thermostatic control knob). The TS 2000 gas-fired convector is an independent heat- The sealed combustion chamber is the best guarantee of ing appliance with sealed combustion chamber and natu- safety for the environment in which the gas-fired convec- ral draught with balanced flow. -
Page 8: Technical Data
Transport and positioning TECHNICAL DATA Table 1.1 Technical data TS 2000 Heating mode Heat input nominal (1013 mbar - 15 °C) (1) Heat output nominal Efficiency nominal heat input 85,8 Installation data G20 natural gas (nominal) m³/h 0,20 Gas consumption G30 (nominal) -
Page 9: Minimum Clearance Distances
3.3.1 Gas connection 3/8" ▶ on the right, at the bottom. Install an anti-vibration connection between the ap- ▶ pliance and the gas piping. The connection to the gas mains must be made Installation, use and maintenance manual – TS 2000... -
Page 10: Combustion Products Exhaust
▶ pipe (see Figure 3.1 p. 10 ). 3.4.2 Installation types The flue gas exhaust/air intake of the TS 2000 gas-fired Figure 3.1 Ø 130 hole drilling convectors must be carried out, using the supplied coax- ial pipes, on the installation wall (maximum pipe length 50 cm). - Page 11 Flue gas exhaust pipe Air pipe Figure 3.5 Installation of coaxial pipes and terminal Support bracket Gasket Support bracket fixing holes Flue gas exhaust pipe External windproof terminal Air pipe Holes for fixing the terminal Installation, use and maintenance manual – TS 2000...
-
Page 12: First Start-Up
First start-up entails checking/setting up the com- actions bustion parameters and may exclusively be carried out by a Robur TAC. NEITHER the user NOR the in- Should the TAC find any non conformities, the user/install- stallation technician is authorised to perform such er is bound to perform any corrective procedures required operations, under penalty of voiding the warranty. - Page 13 Minimal heat input mbar 15,0 2. Adjust the gas pressure at the minimum heat input to mbar 18,0 the required value (Table 4.1 p. 13 ) by means of the Installation, use and maintenance manual – TS 2000...
-
Page 14: Gas Changeover
First start-up Table 4.2 Gaz nozzles pressure regulator D. By turning counterclockwise the pressure increases, clockwise it decreases. TS 2000 3. Check the pressure value after removing the screw- Installation data driver from the adjustment screw. 3.00/1,20 (1) Diameter (Ø) 3.00/0,70 (1) GAS CHANGEOVER 3.00/0,70 (1) -
Page 15: Normal Operation
3. Press the knob fully. 4. While keeping the knob pressed down, press button A The operation of the TS 2000 gas-fired convectors is con- on the piezo igniter of the pilot flame. trolled by the control knob on the appliance. -
Page 16: Maintenance
Maintenance MAINTENANCE WARNINGS ANY MALFUNCTIONS OF OPERATION Before taking any particular measures, always check that: Correct maintenance prevents problems, assures „ The gas is supplied. efficiency and keeps running costs low. „ The supply pressure at the burner is within the specified tolerance range. -
Page 17: Appendices
Permanent pilot flame power requirement Pilot flame power requirement (if 0,200 pilot applicable) Contact details Robur SPA, Via Parigi 4/6, I-24040 Zingonia (BG) (*) NO = nitrogen oxides Installation, use and maintenance manual – TS 2000... - Page 20 Robur mission Robur is dedicated to dynamic progression in research, development and promotion of safe, environmentally-friendly, energy-efficiency products, through the commitment and caring of its employees and partners. Robur S.p.A. advanced technologies for air conditioning via Parigi 4/6 24040 Verdellino/Zingonia (BG) Italy +39 035 888111 - F +39 035 884165 www.robur.it robur@robur.it...
Need help?
Do you have a question about the TS 2000 and is the answer not in the manual?
Questions and answers