Advertisement
W A T E R
S O U R C E
H E A T
Installation, , , ,
Installation
Installation
Installation
Operation
Operation an
Operation
Operation
Maintenance
Maintenance
Maintenance
Maintenance
Instructions
Instructions
Instructions
Instructions
Important:
Important: These instructions are for the use of specially
Important:
Important:
trained personnel, experienced in the installation of this
equipment and related systems. Some states require
licensing of installation and service personnel.
Unqualified individuals should not attempt to interpret
these instructions or install this equipment. Read
instructions carefully before unpacking, installing and
operating unit.
Inspection: This heat pump has been factory inspected;
Inspection:
Inspection:
Inspection:
however, we recommend you check the carton and
inspect the unit for concealed shipping damage. Note
any transit damage on all copies of the bill of lading.
Purchasers must file transit damage claims promptly
with the freight company.
Handling: Always move the unit with care and in the
Handling:
Handling:
Handling:
horizontal position as shipped on pallet. Moving the heat
pump on its side or dropping it may damage internal
parts.
Storage: Store in a clean, dry and protected area.
Storage
Storage
Storage
Location: Install units indoors in an area that provides
Location:
Location:
Location:
for maintenance access.
P U M P S
an
and d d d
an
Advertisement
Table of Contents
Related Manuals for Mammoth J036HHC
Summary of Contents for Mammoth J036HHC
- Page 1 W A T E R S O U R C E H E A T P U M P S Installation, , , , Installation Installation Installation Operation Operation an Operation Operation and d d d Maintenance Maintenance Maintenance Maintenance Instructions Instructions Instructions...
-
Page 2: Installation
A flat washer and two nuts (not supplied by Note: The unit is shipped from the factory with access to Mammoth) should be used to mount the unit on the ceiling- attached threaded rods. When installed, the heat pump... - Page 3 Figure 1: Horizontal mounting detail (L009-J072H) NOTES 1）DOWN ACCESS FILTER GUIDES ARE ABLE AS OPTION 2）USE A BACKUP WRENCH ON FITTINGS WHEN MAKING WATER CONNECTIONS 3）DO NOT SCREW DUCTWORK INTO THE HEAT PUMP CABINET USE HANGER RODS THE FLANGES PROVIDED ON FIL TER GUIDES AND BLOWER （BY OTHERS）...
- Page 4 Figure 4 Horizontal mounting detail (J086~142H) OISTING FEET AT THE UNIT BOTTOM OF THE VIBRATION ISOLATION GROMMET (SEE FIGURE 5) Figure 5: Grommet detail THREADED ROD （BYOTHERS） HANGER BRACKET VIBRATION ISOLATION GROMMET WASHER（BYOTHERS） MUST COVER ENTIRE BOTTOM OF GROMMET RETAINING NUTS （BYOTHERS）...
-
Page 5: Water Supply
Do not 1" Min. Internal Trap use wrench on hose or on the sleeve that crimps the fitting onto (By Mammoth) the hose. Hoses must not be pulled taut, twisted or kinked. Connections should not be over tightened. -
Page 6: Electric Supply
Electric supply Diagram 1: Manual changeover thermostat Electrical Electrical Service Service and and Fusing Fusing Electrical Electrical Service Service Fusing Fusing Warning: To avoid severe electrical shock, turn off power before TERMINAL servicing controls. ○ ○ ○ ○ ○ STRIP Unit must be installed in compliance with NEC and local codes. - Page 7 Electric supply Diagram 5: Model L013～L030HLC -* wiring schematic SCHEMATIC DIAGRAM Diagram 6: Model J036~J072HLC-* wiring schematic J086-J142H: See the unit label for the detail electric diagram...
- Page 8 NOTES: 1. All units are factory-wired to customer order. For 208 Volt/60 Hz or 200 Volt/50 Hz, use the black and red transformer leads. For 230 Volt/60 Hz or 220 Volt/50 Hz or 220/240 Volt/50 Hz units, use the black and orange transformer leads. For 265 Volt/60 Hz units, use the black and brown transformer leads.
- Page 9 Figure 7: Discharge conversion Discharg Discharge e e e Conversio Conversion n n n – – – – Horizonta Horizontal l l l Unit Unit Discharg Discharg Conversio Conversio Horizonta Horizonta Unit Unit All horizontal unit sizes from 006H to 072H can be field-converted from straight discharge to side discharge.
-
Page 10: Options Operation
Operation Compressor Compressor Compressor Compressor Mammoth heat pumps have been designed with switches that protect the unit’s refrigerant system. They will automatically shut down the compressor if refrigerant pressure rises too high or Startup Startup Startup Startup drops too low. - Page 11 Sound Sound Packages Packages – – – – Adds additional sound absorbing material Sound Sound Packages Packages Freezestat Freezestat Freezestat Freezestat – – – – Includes a leaving water temperature sensor to the unit casing. wired to the microprocessor board. If the water drops below the set point, the unit will lockout.
-
Page 12: Microprocessor Control
Microprocessor Condensate Condensate Condensate Condensate Overflow: Overflow: Overflow: Overflow: A sensor in the drain pan electrically senses the presence of water. Switch is tied to the safety lockout circuit. control For a complete description of the operation of the Compressor Compressor Compressor Compressor Anti... - Page 13 T T T T rips rips rips rips and and Power Power Power Power Loss Loss Loss Loss Auto Auto Mode Auto Auto Mode Mode Mode Check that Shunt #2 is on “AUTO” and attach Shunt #1 to one Manual Manual Manual Manual Mode...
Need help?
Do you have a question about the J036HHC and is the answer not in the manual?
Questions and answers