Related Manuals for Panasonic NA-F50GD
Summary of Contents for Panasonic NA-F50GD
- Page 1 Order No.HUD0310342C3 Washing Machine NA-F50GD Product Color : White,Grey 2003 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. SPECIFICATIONS...
-
Page 2: Schematic Diagram
760 r/min. Power source AC220V , 230V Spin r/min. 50Hz (Clothes load) Dimension (Width)562mm (Depth)570mm Machine weight 33kg (Height)1006mm Water level Water only Clothes load Power Input selector consumption 49L - 56L 49L - 5.0kg AC220V 310W (standaedized (Motor) 44L - 50L 44L - 3.8kg AC230V 320W... - Page 3 3.1. Timer type drying function It’s possible to dry small amount (Below 1.5kg) of laundry just after spinning or finish drying under open-air drying. The heater, fan motor and fan case are providing inside of the panel, and drying function shall be operated by timer control.
- Page 4 Laundry capacity 1.5kg Putting in too many garments will lessen the dryer’s effect and cause wrinkles. Remaining time indication for drying It is not possible to indicate remaining time more than 100 min. due to two digit. therefore, even select more than 2 hours (2, 3 and 4 hours), “--”mark shall be indicated at start of drying and indicate proper remaining time from 90 min.
- Page 5 Activating “Tub Dry” after the wash is complete eliminates the humidity in the tub that is one cause of black mold. (Activate once a week) 1. Turn on the power supply / Press DRY to select “Tub Dry”. 2. Close the inner cover and the lid and press START The washing machine will rotate the tub quickly and blow in hot air for roughly 30 minutes.
-
Page 6: Drying Tips
5. OPERATIONS 6. DRYING TIPS... -
Page 7: Check Prior To Start Up
7. CHECK PRIOR TO START UP... -
Page 8: Disassembly Instructions And Adjustments
8. DISASSEMBLY INSTRUCTIONS AND ADJUSTMENTS... - Page 9 P.C.Board 1 Open the lid, and remove the panel A packing, and remove a screw mounting the panel face. 2 Slide the panel face to right to remove. 3 Turn the panel face front side back. In case to replace the P.C.Board for operation side. 4 Remove both connectors of the push switch and intermediary lead wire.
- Page 10 Water 1 Slide the lid hinge shaft to right to remove, and remove level the lid. detector, Filling solenoid (Feed valve), safety switch 2 Remove the panel A. 3 Remove 2 screws mounting the filling solenoid (feed valve). 4 Remove the filling solenoid (feed valve) from the detergent case A.
- Page 11 Heater, 1 Slide the lid hinge shaft to left to remove, and remove Fan case A the lid. 2 Remove the panel base. 3 Remove each connectors of the heater, detector and motor. 4 Remove 3 screws mounting the fan case unit. 5 Loosen the hose clamp, and remove the air supply 6 Remove 4 pawls of the fun case A, and remove the case C (Made of steel) from inside.
- Page 12 4 Slide portion of the geared motor shall be removed the coupler. 1 Remove 2 screws mounting the body B. Mechanism case 2 Hold the body B, and pull the rear portion upward slightly. And slide the body B frontward as shown in figure. (Holding pawls at front portion) 3 Remove the feed hose and Air supply hose from the outer tub cover.
-
Page 13: Test Running Without Water
6 Remove the spinner shaft flange nut and the spinner shaft washer B. 7 Pull upward the tub to remove. 8 Lay down the machine on it nothing drain hose side. [NOTE] Please spread cloth to prevent scratch on the body. 9 Remove 2 screws mounting the mounting plate B. - Page 14 Number of Check contents Lamp Operation condition Check times the ” illumination Water level” condition Mode button is pressed End signal When the end buzzer sounds three times,”88” will simultaneously flash on and off in the remaining time Time indication the power will automatically be switched off immediately Auto power off operation is finished.
- Page 15 stopped and warning buzzer will sound (All of U and H21), and an error indication will be display -ed Alphabet and Number alternately. Indication Contents Check point Method to clear Malfunction of Opening and closing Is something wrong with the drain hose? drain lid.
- Page 16 Indication Contents Check point Method to clear Malfunction of Press Power (Push) Check if condition of the fan motor and the PC.Board (Power side). fan motor switch to OFF position Malfunction of Press Power (Push) Check if condition of connector and lead wires. heater circuit switch to OFF position Check if condition of the heater and PC.Board (Power side).
- Page 17 Ref. No. Description Part No. Q’ty Remarks A- 1 Cap A AXW514X6DK0 White A- 1 Cap A AXW514J6DK00 Grey A- 2 Panel A AXW1CD6LX0 White A- 2 Panel A AXW1CJ6LX0 Grey A- 3 Lid hinge shaft AXW193W5U80 A- 4 lid hinge spring AXW1116-6JU0 A- 5 AXW1GD6PF00...
- Page 18 Ref. No. Description Part No. Q’ty Remarks A-42 Cover AXW162J6LX0 Grey A-43 Lead wire unit AXW14A-6PF00 A-44 Switch instructions AXW657-6PF00 Cantonese A-44 Switch instructions AXW657-6PFA0 English A-45 Holder B AXW2498Z6PF0 Screw XTWAXW461 Screw XTB4+15BFE 10.3. LOCATION OF PARTS-B 10.4. REPLACEMENT PARTS LIST-B...
- Page 19 Ref. No. Description Part No. Q’ty Remarks B- 1 Body A AXW1AD6PF00 White B- 1 Body A AXW1AJ6PF00 Grey B- 2 Hanger AXW110D6JU0 White B- 2 Hanger AXW110J6JU0 Grey B- 3 Base A AXW301-6KC10 Inc. B-4,5 B- 4 Leg covering AXW339-6LX0 B- 5 Adjustable leg plate...
- Page 20 10.6. REPLACEMENT PARTS LIST-C...
- Page 21 Ref. No. Description Part No. Q’ty Remarks C- 1 Lint filter AXW22A-6BM0 C- 2 Detergent inlet AXW1198Z6PF0 C- 3 AXW2A-6PF00 Includes C-1,2 C- 4 Suspension unit AXW340Z-6LX5 1 set=4 PCs. C- 5 Outer tub AXW12A-6KC0 Inc. C-20 C- 6 Motor AXW401-56305 220-230V C- 7...
- Page 22 Ref. No. Description Part No. Q’ty Remarks Case A AXW9001D6PF0 White, H.K Case A AXW9001J6PF0 Grey, H.K Case A AXW9001D6PFA White, S'pore Case A AXW9001J6PFA Grey, S'pore Operating instructions AXW9901Z6PF0 English, Cantonese Case B AXW90B-6PF00 Body cover AXW9004Z6PF0 1 set=2 PCs. Tub support A AXW9054Z6PF0 Tub support B...