Labomed SL 20i User Manual

Slit lamp

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

SL 20i

Slit Lamp

User Manual

To ensure proper use of this instrument as well as to avoid injury while operating

Instrument, understanding this manual completely before use is highly recommended.

Part No: 8126700-795

Issue 1.0

Printed on June,2019

Table of Contents

Need help?

Do you have a question about the SL 20i and is the answer not in the manual?

Questions and answers

Summary of Contents for Labomed SL 20i

Page 1 SL 20i Slit Lamp User Manual To ensure proper use of this instrument as well as to avoid injury while operating Part No: 8126700-795 Instrument, understanding this manual completely before use is highly recommended. Issue 1.0 Printed on June,2019...
Page 2 Labotech and Labo America Inc. Reserves the right to make change in the product described in this manual without notice and without incorporating those changes in any products already sold. ISO 13485 Certified - LABOMED products are designed and manufactured under quality management system conforming to ISO 13485 requirements.
Page 3: Table Of Contents
TABLE OF CONTENTS WARNINGS AND CAUTIONS SYMBOL INFORMATION INTRODUCTION INDICATIONS FOR USE CONTRAINDICATIONS SETUP PART IDENTIFICATION SL 20i PACKAGE CONTENTS ACCESSORIES UNPACKING & INSTALLATION APPLICATION OF INPUT POWER DISCONNECTION OF INPUT POWER INSTRUCTIONS FOR USE OPERATION SLIT LENGTH FILTER DIAL SLIT ROTATION CLEANING &...
Page 4: Warnings And Cautions
WARNING: DO NOT REPAIR OR SERVICE THIS INSTRUMENT WITHOUT AUTHORIZATION FROM THE MANUFACTURER OTHERWISE YOU MAY LOOSE WARRANTY CLAIM. ANY REPAIR OR SERVICE TO THIS INSTRUMENT MUST BE PERFORMED ONLY BY EXPERIENCED PERSONAL OR DEALERS TRAINED BY LABOMED OR SERIOUS INJURY TO THE OPERATOR OR PATIENT MAY OCCUR.
Page 5 EQUIPMENT. CAUTION: THIS INSTRUMENT IS NOT INTENDED TO BE CONNECTED TO EQUIPMENT OUTSIDE THE CONTROL OF LABOMED OR MUST BE TESTED TO AN APPLICABLE IEC OR ISO STANDARDS. CAUTION: CHIN REST PAPER-FOR SINGLE USE ONLY. REPLACE WITH EACH PATIENT. Issue 1.0...
Page 6: Symbol Information
SL 20i EXPLANATION OF SYMBOLS The following symbols appear on the instrument: Caution symbol indicating important operating and maintenance Instructions that are included in this User’s Guide. Type B Applied Part Alternating Current Power Protective Earth Connection ON/OFF Manufacture LABOMED...
Page 7: Introduction
INDICATIONS FOR USE The SL 20i Slit Lamp is an AC-powered slit lamp biomicroscope that is intended for use in examining the anterior segment, from the corneal epithelium to the posterior capsule. It is used to aid in the diagno- sis of diseases or trauma, which affect the structural properties of the anterior segment of the eye.
Page 8: Setup
SL 20i SETUP PART IDENTIFICATION SL 20i PACKAGE CONTENTS 1. On/Off Switch 1. SL 20i Slit Lamp HL (8126700) 2. Illumination level Control 2. User’s Guide (8126700-795) 3. Joystick Tracking Plate 4. Joystick for horizontal and vertical movement ACCESSORIES 5. Bulb Access Door 6.
Page 9: Unpacking & Installation
SL 20i SETUP (continued) UNPACKING AND INSTALLATION Metal Plate 1. Open the Cardboard shipping box to see the Ther- mocol Box Inside. 2. Remove the User’s Guide and follow it for Slit Lamp installation. Figure- 1 Table Top 3. On Top of the Thermocol box Table top metal plate form is placed as Shown in Figure-1.
Page 10 SL 20i SETUP (continued) Slide UNPACKING AND INSTALLATION (continued) 7. Install the Slit Lamp Base Assembly onto the track of the Table Top and slide the Guide Rail Covers around the tracks. Refer to Figure-5. Lock the base at any position to prevent any undesired movement Figure- 5 Install Base by using Base Locking Knob Shown as (A) in Fig.
Page 11: Application Of Input Power
SL 20i SETUP (continued) UNPACKING AND INSTALLATION 14. Install the Binocular Assembly & Eyepieces to the Magni- changer using knob ‘X’. Microscope Assembly 15. Unscrew the Knob A Shown in Figure-5 to allow slit lamp to travel on Metal Plate form.
Page 12: Instructions For Use
SL 20i INSTRUCTIONS FOR USE OPERATION 1. Turn on the power using the On/Off switch located on the front of the power supply. Brightness can be adjusted by rotating the illumination level knob. Change the knob for brighten control. Projected NOTE: The maximum position is for intermittent use only.
Page 13: Slit Length
SL 20i INSTRUCTIONS FOR USE (continued) Magniﬁcation Lever OPERATION NOTE: Lock the base whenever the lamp is not in use. 12. The slit width can be adjusted by rotating the Slit Width/ Rotation Knob on either side of the instrument. Refer to figure-15.
Page 14: Cleaning & Maintenance
SL 20i CLEANING AND MAINTENANCE WARNING: RISK OF ELECTRIC SHOCK. ALWAYS DISCONNECT THE POWER CORD FROM THE WALL AND THE INSTRUMENT BEFORE PERFORMING ANY OF THE FOLLOWING CARE AND MAINTENANCE PROCEDURES. EXTERNAL CLEANING Clean the external surfaces of this instrument using a clean,...
Page 15: Replacement Of Chin Rest Light Indicator
SL 20i Replacement of Chin Rest Light Indicator LED Cap 1. Unscrew the LED cap refer fig.-28. 2. Pull out the defective LED and replace with new LED. Figure-28 Changing refer fig.-28A. Thread in the LED cap back. Target Light LED NOTE: If New LED does not light up after switching on.
Page 16: Troubleshooting
Bulb not installed properly. bulb housing. The following is a checklist of items that need to be assessed in order to determine if the SL 20i Slit Lamp requires servicing. • Check the outside of the Slit Lamp for any damage or missing components.
Page 17: Specifications
SL 20i SPECIFICATIONS Catalog Number 8126700-795 Physical Dimensions Size: Height: 19.8 in. (50.2 cm) Weight, unpacked: 23.0 lbs. (10.4 Kg) Width: 10.5 in. (26.7 cm) Weight, packed: 52 lbs (23.64 Kg) Depth: 14.0 in. (35.6 cm) Electrical Voltage: 100-240V AC...
Page 18: Disposal
SL 20i SPECIFICATIONS (continued) Movement Ranges Longitudinal (In/Out) 80mm Lateral (Left/Right) 109mm Vertical (Up/Down) 30mm Chin rest Range 80mm Fine movement 13mm (Cross Slide) DISPOSAL This product does not generate any environmentally hazardous residues. At the end of its product life, follow your local laws and ordinances regarding the proper disposal of this equipment.
Page 19: System Configuration
SL 20i SYSTEM CONFIGURATION 6134120-122 TONOMETER MOUNT 8122595-812 6134130-113 ZEISS ADAPTER KIT H.S ADAPTER KIT 8122600-852 8122600-851 SONY HANDICAM 6134131-107 I-PHONE-6 (6134172-1-6) SONY HANDICAM ADAPTER 6134120 DSLR ADAPTER 6134131 I-PHONE-6 PLUS (6134172-1-6P) 8122600-800 I-PHONE 7 (6134172-1-7) CCD CAMERA I-PHONE ADAPTER...
Page 20: Guidance Tables
Guidance and Manufacturer’s Declaration – Electromagnetic Emissions The SL 20i is intended for use in the electromagnetic environment specified below. The customer or user of the SL 20i should ensure that it is used in such an environment. Electromagnetic Environment...
Page 21 Guidance and Manufacturer’s Declaration – Electromagnetic Immunity The SL 20i is intended for use in the electromagnetic environment specified below. The customer or user of the SL 20i should ensure that it is used in such an environment. Immunity IEC 60601...
Page 22 Guidance and Manufacturer’s Declaration – Electromagnetic Immunity The SL 20i is intended for use in the electromagnetic environment specified below. The customer or user of the SL 20i should ensure that it is used in such an environment. IEC 60601...
Page 23 Portable and Mobile RF Communications Equipment and the SL 20i The SL 20i is intended for use in the electromagnetic environment in which radiated RF disturbance are controlled. The customer or user of the SL 20i can help prevent Electromagnetic...
Page 24: Warranty
Lamps, bulbs, charts, cards and other expendable items are not covered by this warranty. All claims under this warranty must be in writing and directed to the LABOMED factory, or authorized instrument dealer making the original sale ands must be accompanied by a copy of the purchaser’s invoice.
Page 25 Revision History Rev. No. Date of Release DCR # Change App. By...
Page 26 Labo America Inc. 920 Auburn Court Fremont, CA 94538 U.S.A. Phone: 510-445-1257 Fax: 510-991-9862 E-mail: sales@laboamerica.com www.laboamerica.com EU REP. Labomed Europe Essebaan 50 NL-2908 LK Capelle a/d IJssel The Netherlands Tel: +31 (0)10 4584222 Fax: +31 (0)10 4508251 E-mail: info@labomedeurope.com...

This manual is also suitable for:

8126700-795