Table of Contents
Advertisement
How to use this file...(Operators Manuals)
————————————————————————————————————————————–––
Instructions for
Print Vendors (Paper Manuals)
Paper Size:
* 11 x 17
* Body—50 lbs brilliant white offset or equivalent.
* Cover—on pre-printed two-tone "Swash" stock.
P r e s s :
* Body—1-color, 2-sided
* Cover imprint —1-color, 1-sided
Bindery:
* Saddle Stitch, Face Trim
* Face Trim
C O V E R S :
* This file contains several manuals, which differ only in their covers.
* Covers are all present at the beginning of this file.
* Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover.
• Check the front cover for the individual part number (typically a 171xxxx number).
B O D Y :
• The body of the manual is identical, regardless of the cover used.
* REMEMBER: ODD number pages are ALWAYS right hand pages, and EVEN number are ALWAYS
left hand pages.
G e n e r a l :
* This instruction page is NOT part of the manual and must NOT be printed.
• Pages labeled with the text "THIS PAGE INTENTIONALLY BLANK" are placement pages ONLY,
and should NOT be printed.
————————————————————————————————————————————–––
If you have further questions on how to utilize this file, please contact
Simplicity Technical Publications Department at (262) 284-8647.
Advertisement
Table of Contents
Related Manuals for Simplicity Massey Ferguson Agco Allis 1692934
Summary of Contents for Simplicity Massey Ferguson Agco Allis 1692934
- Page 1 • Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY, and should NOT be printed. ————————————————————————————————————————————––– If you have further questions on how to utilize this file, please contact Simplicity Technical Publications Department at (262) 284-8647.
- Page 2 THIS PAGE INTENTIONALLY BLANK...
- Page 3 ATTACHMENT OPERATOR’S MANUAL 46” Single-Stage Snowthrower 46” Single-Stage Snowthrower Mfg. No. Description 1692934 46” Single Stage Snowthrower (for use with Legacy / 2000 / 2900 Series) 1693761 46” Single Stage Snowthrower (for use with Legacy / 2000 / 2900 Series) 1717485-02 Rev 7/2000 TP 100-2099-02-AT-SMA...
- Page 4 M A N U F A C T U R I N G , I N C . 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 1997 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.
-
Page 5: Table Of Contents
General Required Accessories OPERATION AND USE Two Simplicity 1693160 50 lb. wheel weights (one per rear Recommended Accessories .......1 wheel) OR two 50 lb. Simplicity Quick Tach weights (1692939) Safety Decals ..........1 and rear weight carrier (1692941) are required when using this Safety Rules..........2... -
Page 6: Safety Rules
Safety Rules Read these safety rules, and the safety rules in your tractor Operator’s Manual, and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment. The triangle in the text signifies important cau- tions or warnings which must be followed. -
Page 7: Operation
Operation OPERATION Controls Read and understand the instructions in your tractor Operator’s Manual. Refer to Figure 1 for control locations. A. ELECTRIC CHUTE ROTATOR Rotates the chute right and left. B. PTO SWITCH Engages and disengages the snowthrower. C. ATTACHMENT LIFT Raises the snowthrower off the ground for transport. - Page 8 Operation Snow Removal Suggestions IMPORTANT NOTE • Determine the best snow removal pattern before Always raise the snowthrower before turning or beginning. backing up, to prevent damage to the unit. • Wind direction is an important factor to consider. Transporting Rotate the spout to discharge snow downwind.
-
Page 9: Maintenance
Maintenance Schedule For Normal Care WARNING To avoid serious injury, perform maintenance on Care Required Schedule the tractor or snowthrower only when the engine is stopped, parking brake is set and all moving parts Clean snow and ice from After each use. have stopped. - Page 10 (see Figure 8). 5. Remove the plug using a 1/4” Allen wrench. 6. While holding the gear box level, add Simplicity Winter Weight Worm Gear Oil to the fill hole until oil runs out the level hole.
-
Page 11: Adjustments
Adjustment Figure 9. Adjusting Skid Shoes ADJUSTMENTS Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface. On surfaces such as gravel, the scraper bar should be set high enough so that it will not pick up debris. 1. -
Page 12: Troubleshooting
Troubleshooting Locate the problem you’ve encountered in the chart below. Check the possible causes one at a time in the order list- ed. Correct any problems that are found and operate the snowthrower to see if you have eliminated the problem. WARNING To avoid serious injury, perform maintenance on the tractor or snowthrower only when the engine is stopped, parking brake is set, and all moving parts have stopped. -
Page 13: Initial Assembly
Initial Assembly Figure 13. Front Hitch Mounting Brackets A. Hitch Bracket C. Capscrews, B. Frame 5/16-18 x 1-1/4” D. Nut & Lockwasher Bracket Mounting Holes Located Here Figure 12. Front Hitch Bracket Mounting Holes INITIAL ASSEMBLY NOTE: Once installed, the front and rear hitch mounting brackets need not be removed. -
Page 14: Assemble Ladder Hitch
Initial Assembly Assemble Ladder Hitch 1. Attach the hanger brackets (A, FIgure 17) using 5/16- 18 x 1” capscrews and nylock nuts (B). Do not torque the nuts. The hanger brackets (A) should be able to pivot freely. 2. Attach the lift rod (C, Figure 17) to the hitch lift arm (D) using one 1/2”... -
Page 15: Assemble Discharge Chute
Initial Assembly Figure 22. Discharge Chute Motor Adjustment A. Adjustment Screws B. Plastic Cover Figure 21. Assemble Discharge Chute A. Plastite Screw B. Hold-Down C. Chute Ring Assemble Discharge Chute 1. Remove the three hold downs (B, Figure 21) and plastite screws (A). -
Page 16: Hitch Installation
Hitch Installation HITCH INSTALLATION Install Hitch Onto Tractor 1. Slide the hitch and lift rod assembly under the tractor. Use 4x4 wood blocks to support the hitch and help align the mounting holes. 2. Attach the rear end of the ladder hitch (B, Figure 24) the to the rear hitch brackets (A) using two 5/8 x 1- 5/8”... -
Page 17: Snowthrower Installation
Snowthrower Installation Grease Here Before Assembly Figure 27. Attach Drive Shaft A. Locking Collar Figure 26. Attach Snowthrower A. Dozer Pins C. Attachment Hooks B. 5/8 x 1-5/8” Flat Head Clevis Pin SNOWTHROWER INSTALLATION 1. Install the lift arm extension if not already done (see Install Attachment Lift Extension under INITIAL ASSEMBLY for instructions). -
Page 18: Snowthrower & Hitch Removal
Snowthrower & Hitch Removal Figure 30. Remove the Drive Shaft A. Locking Collar SNOWTHROWER & HITCH REMOVAL NOTE: Whenever removed, install clevis pins, hitch pins, Figure 31. Remote Defector Control clips and hardware onto snowthrower and hitch for stor- A. Remote Deflector Control age. -
Page 19: Hardware Id & Torque Specs
Hardware Identification & Torque Specifications Common Hardware Types Torque Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Washer Hardware Lockwasher Marks Grade Carriage Bolt SAE Grade 2 SAE Grade 5 SAE Grade 8 Hex Nut Size Of in/lbs in/lbs in/lbs... -
Page 20: Drill Deflector Control Mount Holes
Mount Remote Deflector Control Early Models Mark and Drill Two 9/32” Holes Line Template Up with Edge of Plastic Dashboard Current Models Mark and Drill Two 9/32” Holes Line Template Up with Bottom of Plastic Dashboard DRILL HOLES TO MOUNT REMOTE DEFLECTOR CONTROL NOTE: Read through instructions before beginning. - Page 21 Remote Deflector Control Template Use These Holes with Early Models Line Template Up Use These with Edge of Holes with Plastic Current Dashboard Models Mark and Drill Two 9/32” Holes Line Template Up with Bottom of Plastic Dashboard...