Ventrac LX420 Owner/Operator's Manual & Parts List

Ventrac LX420 Owner/Operator's Manual & Parts List

Hide thumbs Also See for LX420:

Advertisement

Quick Links

OWNER/OPERATOR'S
MAN UAL & PARTS LIST
SNOW BLOWER
Model LX420
Re vised 01/08/20
09.10039

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LX420 and is the answer not in the manual?

Questions and answers

Summary of Contents for Ventrac LX420

  • Page 1 OWNER/OPERATOR’S MAN UAL & PARTS LIST SNOW BLOWER Model LX420 Re vised 01/08/20 09.10039...
  • Page 2 Prod uct Iden ti fi ca tion If you need to con tact an Au tho rized Ventrac Dealer for in for ma tion on ser vic ing your prod uct, al ways pro vide the Prod uct Model and Se rial num bers.
  • Page 3: Table Of Contents

    TA BLE OF CON TENTS IN TRO DUC TION SEC TION A De scrip tion & Spec i fi ca tions ........A-1 SAFETY SEC TION B Safety Sym bols .
  • Page 4 Prod uct De scrip tion LX420 Snow Blower The Ventrac Model LX420 Snow Blower is a powerful, high capacity, two-stage snow blower. It combines an aggressive sixteen inch auger with a heavy duty, high speed fan to make a powerful and efficient snow removing attachment for the Ventrac 3000 series tractors.
  • Page 5 SAFETY AT TEN TION This sym bol iden ti fies po ten tial health and safety haz ards. It marks safety pre cau tions. Your safety and the safety of oth ers is in volved. SIG NAL WORD DEF I NI TIONS In di cates an im mi nently haz ard ous sit u a - tion which, if not avoided, will re sult in death or se ri ous in jury.
  • Page 6: De Cals

    SAFETY The fol low ing de cals must be main tained on your Ventrac At tach ment. If any de cals are faded or miss ing, con tact your dealer promptly for re place ments. Page & De cal Description...
  • Page 7: Gen Eral Safety Pro Ce Dures

    SAFETY Gen eral Safety Pro ce dures for Ventrac Trac tors, At tach ments, & Ac ces sories Read and understand the operator’s manual before operating this equipment. Observe and follow all safety decals. DO NOT let children or any untrained person operate the tractor or attachment. Make sure that all operators of this equipment are thoroughly trained in using it safely.
  • Page 8 Before operating any LX420 prior to serial AB1135 with a LE3100 or LE3200 that is Never di rect the snow blower dis charge chute to -...
  • Page 9: Attaching

    OPERATION Attaching Drive the trac tor slowly for ward into the hitch arms on the snow blower. Align the lift arms of the trac tor with the snow blower hitch arms by rais ing or low er ing the front hitch and com plete the en gage ment.
  • Page 10: De Tach Ing

    OPERATION De tach ing Park the trac tor on a level sur face and set the park ing brake.* Raise the snow blower to the high est po si tion and shut off trac tor engine. Place blocks un der snow blower to pre vent it from low er ing. LT3000: To re move the weight trans fer springs, hold down the spring an chor le ver, re move the ball pin, and slowly ro tate the le ver up.
  • Page 11: Belt Re Place Ment

    MAIN TE NANCE/AD JUST MENTS Grease the auger, jack-shaft, & blower shaft bearings approximately every 25 hours. Do not over grease. Usually one or two pumps are sufficient. Additional lubrication may be required in extremely harsh or dirty conditions. Gearbox manufacturers recommend changing the gearbox oil 50 hours after start up and then every 500 hours or seasonally, whichever comes first.
  • Page 12: Chute Ad Just Ment

    MAIN TE NANCE/AD JUST MENTS Belt Ten sion Ad just ment The belt spring tension is adjustable. This adjustment allows some belt slippage to protect the gearbox and drive components in the event an immovable object stops the auger or fan. At the factory, the spring is installed with the least amount of tension.
  • Page 13 PARTS MAN UAL LX420...
  • Page 14: Main Frame & Au Ger Drive

    PARTS IL LUS TRATED DRAW ING MAIN FRAME & AU GER DRIVE...
  • Page 15 34..62.0994 ... . . FRAME, MAIN LX420 ....
  • Page 16: Main Drive & Fan Drive

    PARTS IL LUS TRATED DRAW ING MAIN DRIVE & FAN DRIVE...
  • Page 17 9 ..40.0318 ... . . IDLER ARM, BLOWER DRIVE LX420 ....
  • Page 18: Chute & Hy Drau Lics

    PARTS IL LUS TRATED DRAW ING CHUTE & HY DRAU LICS...
  • Page 19 26..62.1012 ... . . CHUTE, MAIN SNOW BLOWER LX420 ....
  • Page 20: Shields & Decals

    PARTS IL LUS TRATED DRAW ING SHIELDS & DECALS...
  • Page 21 15..60.0874 ... . . SHIELD, GEAR BOX DRIVE LX420 ....
  • Page 22: Cut Ting Edge, Bump Bar, & Skid Shoes

    PARTS IL LUS TRATED DRAW ING CUT TING EDGE, BUMP BAR, & SKID SHOES...
  • Page 23 PARTS CUT TING EDGE, BUMP BAR, & SKID SHOES REF. PART NO. DE SCRIP TION QTY. 1 ..62.1014 ... . . BAR, TU BU LAR BUMP LX ......1 2 .
  • Page 24 PARTS/OPTIONS IL LUS TRATED DRAW ING 12 V AC TU A TOR DE FLEC TOR CONTROL...
  • Page 25 PARTS/OPTIONS 12 V AC TU A TOR DE FLEC TOR CON TROL REF. PART NO. DE SCRIP TION QTY. 1 ..30.0226 ... . . CLAMP, WIRE MT ADH. 3/8 GRAY ......2 2 .
  • Page 26: Weight Trans Fer For Lt3000 Tractors

    PARTS/OPTIONS IL LUS TRATED DRAWING WEIGHT TRANS FER FOR LT3000 TRACTORS...
  • Page 27 PARTS/OPTIONS WEIGHT TRANS FER FOR LT3000 TRAC TORS REF. PART NO. DE SCRIP TION QTY. 1 ..99.SF0404 ... BOLT, SF 1/4-20 X 1/2 ....... . 4 2 .

Table of Contents