Related Manuals for netvox EmberLux BLZ-US-01
Summary of Contents for netvox EmberLux BLZ-US-01
- Page 1 US EmberLux Switch User Manual EmberLux Switch Model: BLZ-US-01 Firmware: V0.6 and below Hardware: V1.0 and below 20150923 FW V0.1~V0.5...
-
Page 2: Table Of Contents
5-4. Turn On ...............................5 BLZ-US-01 5-5. Battery................................6 5-6. Restore to Factory Setting..........................6 6. Home Automation Clusters for ........................6 BLZ-US-01 7. Netvox App control..............................9 8. ZiG-BUTLER................................. 11 8-1. Join into the network........................11 BLZ-US-01 8-2. Bind ..............................11 BLZ-US-01 8-3. -
Page 3: Introduction
1. Introduction Netvox , a battery-powered wall switch, acts as an End Device in ZigBee network. It does not perform BLZ-US-01 permit-join function as a coordinator or a router for other devices to join the network. is featured to control BLZ-US-01 the On/Off device or the dimmable device. -
Page 4: Product Appearance
2. Product Appearance Button 1 (On) LED Indicator Button 2 (Off) Reset Key Battery Holder... -
Page 5: Specification
3. Specification Fully IEEE 802.15.4 compliant Utilizes 2.4GHz ISM band; up to 16 channels Power supply: 2 x AAA batteries Up to 70 meters wireless transmission range in non-obstacle space Easy installation and configuration Operation temperature: -10 ℃~ 50 ℃... -
Page 6: Sleeping Mode
command from Z970A. For example, after binds with Z809B successfully, press control BLZ-US-01 button of the bind device Z809B will receive command and act correspondingly (including BLZ-US-01 normal bind and group bind). A. On/Off control (0x0006) (1) Short press Button 1 (network indicator flash once for 0.5s)→ send the turn-on command. (2) Short press Button 2 (network indicator flash once for 0.5s)→... -
Page 7: Battery
5-5. Battery When the operating voltage is lower than 2.4V, will send a low-power report to the ZigBee network. BLZ-US-01 5-6. Restore to Factory Setting To restore it to factory setting, please follow the steps: Step1. Remove the batteries to power off BLZ-US-01 Step2. - Page 8 8-bit integer 0xff 0x0003 HWVersion Unsigned 0x00 – Read only 8-bit integer 0xff 0x0004 ManufacturerName Character 0 – 32 Read only netvox string bytes 0x0005 ModelIdentifier Character 0 – 32 Read only Z970BE3ED string bytes 0x0006 DateCode Character 0 – 16...
- Page 9 8-bit integer 0xff write 0x0035 Bitmap 0000 Read / BatteryAlarmMask 0000 0001 (8-bits) 000x write BatteryVoltageMinT Unsigned 0x00 – Read / 0x0036 hreshold 8-bit integer 0xff write BatteryVoltageThres Unsigned 0x00 – Read / 0x0037 hold1 8-bit integer 0xff write BatteryVoltageThres Unsigned 0x00 –...
-
Page 10: Netvox App Control
7. Netvox App control 1. Add device to Netvox system, the added device list will show up in device management as below, 2、Click “Setting” into device interface as below: Click “Pairing configuration” into binding interface. Click “Pair Devices ” (ex. LED dimmable light). Click “bind”... - Page 11 After binding, is able to control dimming switch to turn on/off and adjust brightness. If users want to BLZ-US-01 unbind device, long press bind device item, message “unbind” will show up as below on the left as below. (Note: before clicking “unbind”, users need to turn on ED.) After unbinding completely, item will disappear.
-
Page 12: Zig-Butler
8. ZiG-BUTLER 8-1. Join into the network BLZ-US-01 When ZiG-BUTLER sees a coordinator or a router device, it will show the icon. Right click on the icon of the coordinator or the router and choose Set Permit Join On. After has successfully joined, the icon will be appeared in ZiG-BUTLER. - Page 13 (2) On the Device tab, select the device to which you would like to bind. Next, click Select ClusterID, choose the Cluster, and click OK. The information would be pop-up after the binding is completed. Note: to bind the device via Zig-butler, please make sure is on.
-
Page 14: Power Consumption Report
8-3. Power Consumption Report (1) Right click on the End Point of and select Properties to overview the power consumption. BLZ-US-01 (2) In binding list, we can see bind request information of other devices. If bind device and BLZ-US-01 share the same cluster ID: 0001 of binding request. Then will report data to the bind device. - Page 15 (4) On the Device tab, select the device to which you would like to bind. Next, click Select ClusterID, choose the Cluster, and click OK. Choose bind device sharing the same cluster ID: 0001 of binding request through “device’. to choose cluster ID which is needed. (5) Right click on the End Point of and select Properties.
- Page 16 (7) Click set to customize: Min: the minimum reporting internal (second) Max: the maximum reporting internal (second) Reportable change: reports data instantly when the change rate is more than this value. BLZ-US-01...
- Page 17 Report setting interval table： Min Interval Max Interval Reportable Change rate≥ Reportable Change rate＜ (Unit:second) (Unit:second) Change Change Reportable Change To report per Minimum To report per Maximum ≠0 interval interval 1-65534 1-65534 To report per Minimum To report per Minimum interval interval To report per Maximum...
-
Page 18: Related Netvox Devices
9. Related Netvox Devices Z806: Output Unit ZC06: Dimmable LED Tube 10. Important Maintenance Instructions Please keep the device in a dry place. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits. In cases of accidental liquid spills to a device, please leave the device dry properly before storing or using. - Page 19 FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the EmberLux BLZ-US-01 and is the answer not in the manual?
Questions and answers