Page 1 ORIGINAL INSTRUCTIONS OPERATOR’S MANUAL E37C Mini Excavator Part number 90436684 edition English January 2021...
Page 2: Table Of Contents
Contents 1 GENERAL INFORMATION Note to the Owner ................1-1 Intended use.
Page 3 Ventilation and heating ..............3-31 Rearward controls Storage compartment .
Page 4 Shipping transport Handling the machine ..............5-5 Recovery transport Towing the machine .
Page 5 Every 100 hours Fuel filter water separator ............. 6-35 Every 250 hours Battery .
Page 6 Storage Preparing for storage ............. . 6-77 Periodic checks.
Page 7: General Information
NEW HOLLAND CONSTRUCTION customer assistance is also available. Go to www.newholland.com You can obtain manuals on the operation, maintenance and repair of your machine from your NEW HOLLAND CON- STRUCTION Dealer. To ensure quick and efficient service, consult your NEW HOLLAND CONSTRUCTION Dealer for assistance in ordering the correct manuals for your machine.
Page 8: Intended Use
Operations that involve the use of hydraulic hammers are also possible. Other operations, such as moving suspended loads, are only possible if the specific variant approved by the NEW HOLLAND CONSTRUCTION is present. Using the excavator and its equipment for different operations, such as towing, transporting and lifting people, is considered inappropriate and is prohibited.
Page 9: Note To The Owner
Periodic service consists of activities that are necessary these activities may require appropriate facilities, techni- to maintain the expected life of the NEW HOLLAND CON- cal skills, and/or tools that NEW HOLLAND CONSTRUC- STRUCTION machine. These activities have defined in- TION does not supply with the machine.
Page 10 (or meet other applicable local age requirements). These persons must demonstrate the ability to operate All persons training to operate, or who will operate this and service the NEW HOLLAND CONSTRUCTION ma- NEW HOLLAND CONSTRUCTION machine should be chine in a correct and safe manner.
Page 11: Product Identification
Cab version SMIL18MEX0108EA Canopy version When ordering parts, obtaining information, or seeking assistance, always supply your NEW HOLLAND CONSTRUC- TION Dealer with the type and Product Identification Number (PIN) of your machine or accessories. Write the following in the spaces below: •...
Page 12 1 - GENERAL INFORMATION Machine The machine Product Identification Number (PIN) plate (A) is located in the front left-hand side of the upper frame. SMIL19MEX0675AB (1) Product Identification Number (PIN)______________ (2) Type/Model & designation______________________ SMIL16MEX3219AA Engine The engine serial number (A) is located on the engine name plate.
Page 13 1 - GENERAL INFORMATION Emission decal The emission decal (C) is located on the engine. A further emission decal is located inside the engine compartment or inside the cab. It describes important details for using the engine. Make sure to read before using the engine. Also, the emission decal describes details regarding the engine only.
Page 14: Operator's Manual Storage On The Machine
1 - GENERAL INFORMATION Operator's manual storage on the machine Always keep the manual in the location provided for that purpose (below the operator’s seat, in the storage com- partment). NOTE: for the canopy version, you can store the manual in the storage compartment located behind the operator's seat.
Page 15: Machine Orientation
1 - GENERAL INFORMATION Machine orientation The terms "Right-hand", "Left-hand", "Front" and "Rear" are used in this manual to indicate the sides as they are seen from the operator's seat when the travel motors are positioned at the rear and the operator is facing the direc- tion in which the machine advances (forward).
Page 16: Machine Components
1 - GENERAL INFORMATION Machine components Standard version SMIL18MEX0105FB Bucket Oil cooler Bucket tooth Radiator Boom swing cylinder 10. Engine 11. Main pump Tool box Swing motor 12. Hydraulic central joint Fuel tank 13. Main control valve Hydraulic oil tank 1-10...
Page 17 1 - GENERAL INFORMATION SMIL16MEX0047FB 14. Bucket control rod 24. Muffler 15. Bucket control link 25. Muffler pipe 26. Counterweight 16. Side cutter 17. Bucket cylinder 27. Travel motor 18. Dipper 28. Sprocket 19. Dipper cylinder 29. Upper roller 20. Boom 30.
Page 18 1 - GENERAL INFORMATION Angle blade version SMIL18MEX0106FB Bucket Oil cooler Bucket tooth Radiator Boom swing cylinder 10. Engine Tool box 11. Main pump Swing motor 12. Hydraulic central joint Fuel tank 13. Main control valve Hydraulic oil tank 14. Angle blade cylinder 1-12...
Page 19 1 - GENERAL INFORMATION SMIL19MEX0422FB 15. Bucket control link 26. Counterweight 16. Side cutter 27. Travel motor 17. Bucket cylinder 28. Sprocket 18. Dipper 29. Upper roller 19. Dipper cylinder 30. Lower roller 20. Boom 31. Track 21. Boom cylinder 32.
Page 20: Emissions Overview
1 - GENERAL INFORMATION Emissions overview YANMAR CO., LTD. EMISSION CONTROL SYSTEM WARRANTY - USA ONLY Your Warranty Rights and Obligations: The California Air Resources Board (CARB), the United State Environmental Protection Agency (EPA) and YANMAR CO., LTD. hereafter referred to as YANMAR, are pleased to explain the emission control system warranty on your 2016, 2017, or 2018 model year industrial compression-ignition engine.
Page 21 1 - GENERAL INFORMATION Any replacement part which is functionally identical to the original equipment part in all respects may be used in the maintenance or repair of your engine, and shall not reduce YANMAR’s warranty obligations. Add-on or modified parts that are not exempted may not be used.
Page 22 1 - GENERAL INFORMATION What the Emergency Stationary Type Engine Owner must Do: The engines for emergency stationary type generators certified by Federal Law (40 CFR Part60) are limited to emer- gency use only, and the operation for maintenance checks and verification test for functions is required. The total operating hours for maintenance and verification test for functions should not exceed 100 hours per year.
Page 23: Safety Information
2 - SAFETY INFORMATION 2 - SAFETY INFORMATION###_2_### Signal word definitions Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions.
Page 24: Safety Rules - Utility Precautions
2 - SAFETY INFORMATION Safety rules - Utility precautions Call all utility companies before you perform YOU MUST FOLLOW safety precautions when you work near buried utility lines. any machine operation During operation, it is likely that you will be working After you locate any buried utility lines, carefully dig a hole around or near buried utility lines that may include, but to the utility line by hand and/or with automatic vacuum...
Page 25: Safety Rules
2 - SAFETY INFORMATION Safety rules General safety rules Use caution when you operate the machine on slopes. Make sure that all guards and shields are in good con- Raised equipment, full tanks and other loads will change dition and properly installed before you operate the ma- the center of gravity of the machine.
Page 26 2 - SAFETY INFORMATION Unsupported hydraulic cylinders can lose pressure and coolant can spray out if you remove a cap while the sys- drop the equipment, causing a crushing hazard. Do not tem is hot. Allow the system to cool before you remove leave equipment in a raised position while parked or dur- the cap.
Page 27 2 - SAFETY INFORMATION Antidote (internal) : Drink large quantities of water or milk. Keep out of reach of children and other unauthorized per- Do not induce vomiting. Seek medical attention immedi- sons. ately. Seat belts Seat belts must be worn at all times. •...
Page 28 2 - SAFETY INFORMATION Do Not Operate tag Before you start servicing the machine, attach a ‘Do Not Operate’ warning tag to the machine in an area that will be visible. Hazardous chemicals If you are exposed to or come in contact with hazardous MSDS, and on manufacturer containers, as well as the in- chemicals you can be seriously injured.
Page 29 2 - SAFETY INFORMATION Maintain a three-point contact with steps, ladders, and Do not use the controls or accessories as hand-holds handholds. when you enter or exit the cab. Never mount or dismount from a moving machine. Working at heights When the normal use and maintenance of the machine •...
Page 30 NEW HOLLAND CONSTRUCTION, make weight, swing bearing, and operator's compartment. In sure the diameter of the pins and the width between the event of problems, consult your NEW HOLLAND the bucket lugs meet the dimensions needed to fit the CONSTRUCTION Dealer.
Page 31 2 - SAFETY INFORMATION • The working area of the end attachment that is mounted • In the event of an operating problem or failure, move may interfere with the machine. Interference may be the machine to a safe place, lower the attachment to the caused due to the type of end attachment or installa- ground, shut down the engine, and remove the ignition tion of parts such as a cab guard.
Page 32 • Before commencing any work on the machine, place a by NEW HOLLAND CONSTRUCTION and in accor- "Do not operate" tag on the right-hand control arm. dance with the instructions, disconnect the batteries, disconnect the alternator B+ and D+ terminal wires, •...
Page 33 2 - SAFETY INFORMATION Using an Implement other than a bucket • When using a special implement (hydraulic breaker, cutter crusher etc.), refer to the operator's manual pro- vided with the implement. Implement operation and maintenance • For the implement operation and maintenance, refer to the operator's manual provided with the implement.
Page 34: Ecology And Environment
CONSTRUCTION strongly recommends that you return ble to your country, and make sure that you understand all used batteries to a NEW HOLLAND CONSTRUCTION this legislation. Where no legislation exists, obtain in- dealer, who will dispose of the used batteries or recycle formation from suppliers of oils, filters, batteries, fuels, the used batteries properly.
Page 35: Hand Signals
2 - SAFETY INFORMATION Hand signals When operating the machine, always work with a signalman when you carry out tasks that require fine control and/or require you to work in areas with poor or impaired visibility. Make sure that you and the signalman understand the signals to be used.
Page 36 2 - SAFETY INFORMATION Stop Lower load or tool Wave one hand back and forth. PDE0006TBP1 PDE0005ATBP1 Slowly raise the load or tool Emergency stop Wave hands back and forth. PDE0007ATBP1 Slowly lower the load or tool PDE0005TBP1 Raise load or tool PDE0007TBP1 PDE0006ATBP1 2-14...
Page 37 2 - SAFETY INFORMATION Turn machine left (swing load left) Lower tool To stop movement, stop moving hand and clench fist. PDE0009TBP1 PDE0008ATBP1 Lift boom Turn machine right (swing load right) To stop movement, stop moving hand and clench fist. PDE0010ATBP1 Lower boom PDE0008TBP1...
Page 38 2 - SAFETY INFORMATION Retract dipper Fill tool PDE0012ATBP1 PDE0011ATBP1 Empty tool Extend dipper PDE0012TBP1 PDE0011TBP1 2-16...
Page 39: Safety Signs
Replace all safety signs that are damaged, missing, painted over, or illegible. If a safety sign is on a part you or your NEW HOLLAND CONSTRUCTION dealer replaces, make sure that you or your NEW HOLLAND CONSTRUCTION dealer install the safety sign on the new part. See your NEW HOLLAND CONSTRUCTION dealer for replacement safety signs.
Page 40 2 - SAFETY INFORMATION Signs positions When you replace a safety sign or other machine sign, make sure you position it as shown below. SMIL18MEX0917GB Cab version A. Cab door E. Hydraulic tank and fuel tank B. Cab window - Right-hand F.
Page 41 2 - SAFETY INFORMATION SMIL18MEX0918GB Canopy version A. Console box - Left hand D. Hydraulic tank and fuel tank B. Counterweight E. Cowl support (engine compartment) C. Console box - Right-hand F. Accumulator of the solenoid valve 2-19...
Page 42 2 - SAFETY INFORMATION (1) Reflecting sign Location: the two reflecting signs are located in the rear side of the machine, on the counterweight. Quantity: 2 Part number: 91M9-04020 The reflecting sign increases the night-time visibility. SMIL19MEX0709AA (2) Keep out of work range of upper structure DANGER Avoid injury! Keep clear of the swing area.
Page 43 2 - SAFETY INFORMATION (3B) Engine access door support caution - High pressure hoses and radiator WARNING Burn hazard! Before performing any service on the hy- draulic system, you must allow it to cool. Hydraulic fluid temperature should not ex- ceed 40 °C (104 °F).
Page 44 2 - SAFETY INFORMATION (3C) Engine access door support caution - Hot surfaces WARNING Burn hazard! Exhaust surfaces are hot! Always wear pro- tective gloves when cleaning or working on the muffler, catalytic converter, or exhaust stack. Failure to comply could result in death or se- rious injury.
Page 45 2 - SAFETY INFORMATION (6) Hydraulic oil WARNING Burn hazard! Before performing any service on the hy- draulic system, you must allow it to cool. Hydraulic fluid temperature should not ex- ceed 40 °C (104 °F). Failure to comply could result in death or se- rious injury.
Page 46 2 - SAFETY INFORMATION (7) Batteries WARNING Battery acid causes burns. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. An- tidote (external): Flush with water. Antidote (eyes): flush with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large quantities of water or milk.
Page 47 2 - SAFETY INFORMATION (8) Keep out of work range of attachment WARNING Falling object hazard! Loss of hydraulic pressure or movement of a control can cause raised equipment to fall. Never work under an implement or attachment supported only by the hydraulic system. Al- ways use suitable equipment to support an im- plement or attachment that must be serviced in a raised position.
Page 48 2 - SAFETY INFORMATION (11) Parking the machine Location: this sign is located on the left-hand console box. Quantity: 1 Part number: 91M8-07300 To prevent unauthorized and unintended movement of the machine, always do the following before you leave the operator’s compartment: 1.
Page 49 2 - SAFETY INFORMATION (14) Emergency exit WARNING Avoid injury! A safety sign indicates which window to use as an emergency exit. Remove this window only in an emergency. Do not place any object that could be an obstacle in case of evacuation in front of this window.
Page 50 2 - SAFETY INFORMATION (17) Angle dozer blade operation Location: this sign is located on the right-hand side of the cab. Quantity: 1 Part number: 94MH-07370 This sign describes the angle blade operations. NOTICE: never jack up or lift the machine with the angle blade placed at an angle.
Page 51 2 - SAFETY INFORMATION (20) Machine control pattern WARNING Unexpected machine movement! Pilot controls have two different machine con- trol patterns. Before you operate the machine, check which pattern is active. Failure to comply could result in death or se- rious injury.
Page 52 2 - SAFETY INFORMATION (21) Danger electric line - Interference with attachments WARNING Fold zone! The booms may hit the cab when folding. Use extra care during manual boom folding and unfolding. Failure to comply could result in death or se- rious injury.
Page 53 This sign warns that accumulator is filled with high pres- sure gas so that near-by fire activity or welding is prohib- ited. Consult the NEW HOLLAND CONSTRUCTION Dealer for the service. (23) Battery position Location: this sign is located on the right-hand side door.
Page 54 2 - SAFETY INFORMATION (24A) Functions of operation levers Cab location: this sign is located in right-hand window of the cab. Canopy location: this sign is located on the right-hand side of the canopy. Quantity: 1 Cab part number: 97MK-07220 Canopy part number: 97MK-07230 This sign describes the functions of operation levers.
Page 55 2 - SAFETY INFORMATION (26) Compliant to Canadian Regulation ICES-002 Cab location: this sign is located on the right-hand side window of the cab. Canopy location: this sign is located on the right-hand side of the canopy. Quantity: 1 Part number: 91K4-14150 This sign shows compliance to Canadian Regulation ICES-002 (vehicles, boats and other devices propelled by an internal combustion engine, electrical means or both).
Page 56 2 - SAFETY INFORMATION (28) Air conditioning refrigerant WARNING Explosion hazard! Air-conditioning refrigerant boils at -26 °C (-15 °F)! -NEVER expose any part of the air-condition- ing system to a direct flame or excessive heat. -NEVER disconnect or disassemble any part of the air-conditioning system.
Page 57 2 - SAFETY INFORMATION (30) Ultra low sulfur fuel Location: this sign is located on the right-hand side of the fuel filler neck. Quantity: 1 Part number: 98Q6-07390 This sign indicates to use low sulfur fuel only (sulfur con- tent < 15 ppm). SMIL19MEX0712AA (31) Lifting point Location: these signs are located on the dozer blade.
Page 58 2 - SAFETY INFORMATION (34) Biodegradable hydraulic oil Location: this sign is located on the hydraulic tank. Quantity: 1 This sign indicates that the vehicle can use biodegradable hydraulic oil. SMIL19MEX0729AA 2-36...
Page 59: Controls And Instruments
3 - CONTROLS AND INSTRUMENTS 3 - CONTROLS AND INSTRUMENTS###_3_### Access to operator's platform Door and steps Cab door CAUTION Pinch hazard! Be careful not to get your hand, clothes, etc. caught in the door when closing it. Failure to comply could result in minor or moderate injury.
Page 60 3 - CONTROLS AND INSTRUMENTS The door can be latched in completely open position. To latch or unlatch the door, operate the lever (3). NOTICE: do not leave the door half-open. Fix it in a latched position. Before performing work with the door open, lock it securely.
Page 61 3 - CONTROLS AND INSTRUMENTS Steps and access handles Cab version WARNING Fall hazard! Clean the steps and access handles to remove all traces of grease, oil, mud, and ice (in win- ter). Failure to comply could result in death or se- rious injury.
Page 62: Operator's Seat
3 - CONTROLS AND INSTRUMENTS Operator's seat Operator's seat In order to operate the machine correctly and with maximum efficiency and comfort, adjust the seat to suit the weight and size of the operator. Fore and aft adjustment • Hold the lever (A) in the raised position. •...
Page 63 3 - CONTROLS AND INSTRUMENTS Seat belt WARNING Equipment failure could cause accident or in- jury! Always fasten the seat belt securely before you operate the machine. Inspect seat belt parts for wear and damage. Replace any and all worn or damaged parts of the seat belt prior to operation.
Page 64: Forward Controls
3 - CONTROLS AND INSTRUMENTS Forward controls Forward controls WARNING Unexpected machine movement! Pilot controls have two different machine control patterns. Before you operate the machine, check which pattern is active. Failure to comply could result in death or serious injury. W1577A This machine is equipped with a lever pattern valve that allows the operator to select between the “ISO type”...
Page 65 3 - CONTROLS AND INSTRUMENTS Right-hand control lever: 5. The boom lowers. 6. The boom raises. 7. The bucket retracts (filling). 8. The bucket extends (dumping). NOTE: the movement speed of the boom or of the bucket depends on the control lever tilt angle. In the intermediate position two movements can be obtained simultaneously.
Page 66 3 - CONTROLS AND INSTRUMENTS Pattern: SAE type Left-hand control lever: 1. The boom lowers. 2. The boom raises. 3. The upper structure swings to the left–hand side. 4. The upper structure swings to the right–hand side. NOTE: the movement speed of the arm or of the swing depends on the control lever tilt angle.
Page 67 3 - CONTROLS AND INSTRUMENTS Right-hand control lever: 5. The dipper arm extends. 6. The dipper arm retracts. 7. The bucket retracts (filling). 8. The bucket extends (dumping). NOTE: the movement speed of the boom or of the bucket depends on the control lever tilt angle. In the intermediate position two movements can be obtained simultaneously.
Page 68 3 - CONTROLS AND INSTRUMENTS Travel control levers and pedals The travel control levers and pedals are used to move the machine. (N): neutral (a) + (b): machine moves forward. (c) + (d): machine moves backward. (b) + (c): opposite simultaneous rotation of the tracks with consequent counterclockwise rotation of the machine around its center axis.
Page 69 3 - CONTROLS AND INSTRUMENTS Boom swing pedal This pedal is used to swing the boom to the right-hand and left-hand direction. Move the lock cover (A) to unlock position by foot. Press the pedal to right-hand side (1) to swing the boom to the right-hand direction.
Page 70 3 - CONTROLS AND INSTRUMENTS Footrest SMIL19MEX0775BA 3-12...
Page 71: Windshield
3 - CONTROLS AND INSTRUMENTS Windshield CAUTION Pinch hazard! Make sure you correctly follow the instructions in this manual when handling the windshield. If you do not handle the windshield correctly, it could slip and injure your fingers or hands. Failure to comply could result in minor or moderate injury.
Page 72: Left-Hand Side Controls
3 - CONTROLS AND INSTRUMENTS Left-hand side controls Left-hand side controls SMIL16MEX1489EB (1) Safety lock lever (refer to page 3-16) The first step activates the head light and the cluster illu- mination lamp. (2) Left-hand control lever (refer to page 3-6) The second step activates the work light and the indicator lamp on the switch.
Page 73 3 - CONTROLS AND INSTRUMENTS Hydraulic quick coupling system switch (op- tional) The hydraulic quick coupling system switch (6) is used to engage or disengage the hydraulic quick coupling system. This switch has a sliding mechanism (A) for preventing erroneous switch operation. Slide the sliding mechanism (A) in the direction of the arrow to lock or unlock the de- vice.
Page 74: Safety Lock Lever
3 - CONTROLS AND INSTRUMENTS Safety lock lever WARNING Unexpected machine movement! When you must leave the operator’s seat, al- ways place the safety lever in the LOCKED po- sition. If the safety lever is unlocked and the control lever is moved unexpectedly, a serious accident could result.
Page 75: Emergency Exit Hammer
Only in case of emergency, use the installed safety ham- mer (1) for breaking the windshield of the cab, and then exit carefully. Consult your NEW HOLLAND CONSTRUCTION dealer for windshield installation. NOTICE: do not break the windshield of the cab except when it is absolutely necessary, such as to escape in an emergency.
Page 76: Windshield Washer Reservoir
3 - CONTROLS AND INSTRUMENTS Windshield washer reservoir This reservoir, located in the left-hand side of the cab, is equipped with an electric pump which is operated from the wiper and washer switch. NOTICE: never operate the windshield washer control when the reservoir is empty.
Page 77: Right-Hand Side Controls
3 - CONTROLS AND INSTRUMENTS Right-hand side controls Right-hand side controls SMIL16MEX1478FB (A) Cab version (9) Auto idle (B) Canopy version (10) Cigarette lighter and 12 V power supply socket: the device is active with the starter key in ON position, or (1) Right–hand control lever (refer to page 3-6) and horn while the engine is running.
Page 78 3 - CONTROLS AND INSTRUMENTS Overload warning switch (optional) The overload warning switch (6), when pressed, activates the overload warning function. When the machine is over- loaded, a buzzer sounds and the red warning light in the instrument cluster is ON. When the overload warning switch is depressed, the buzzers stops sounds and the red warning light in the instrument cluster is OFF.
Page 79 (2) ON: contact, all the systems of the machine operate. The buzzer sounds for 1 s. NOTICE: if this alarm does not sound, the electric cir- cuit is abnormal. Contact your NEW HOLLAND CON- STRUCTION dealer for inspection and maintenance. (3) START: engine ignition.
Page 80: Dozer Blade Control Lever
3 - CONTROLS AND INSTRUMENTS Dozer blade control lever WARNING Hazard to bystanders! ALWAYS make sure the work area is clear of bystanders and domestic animals before starting this procedure. Know the full area of movement of the machine. Do not permit anyone to enter the area of movement during this procedure.
Page 81 3 - CONTROLS AND INSTRUMENTS Angle blade version The angle blade control lever is located on the right-hand console. The basic operation of angle blade control lever are the following: • push the angle blade control lever forward (A) to lower the dozer blade •...
Page 82: Instrument Cluster
3 - CONTROLS AND INSTRUMENTS Instrument cluster The instrument cluster consists of gauges and lights as Pilot lights : indicate operating status of the machine. shown below, to warn the operator in case of abnormal NOTE: the cluster installed on this machine does not en- machine operation or conditions for the appropriate oper- tirely guarantee the condition of the machine.
Page 83 3 - CONTROLS AND INSTRUMENTS 1. Engine coolant temperature gauge The engine coolant temperature gauge indicates the tem- perature of the coolant. The red range (A) lights on when the temperature is above 115 °C (239 °F) The warning light (B) appears and a buzzer sounds when the temperature is above 115 °C (239 °F).
Page 84 3 - CONTROLS AND INSTRUMENTS 4. Air cleaner warning light The air cleaner warning red light (4) is ON when the filter of the air cleaner is clogged. SMIL19MEX0731AA 5. Hydraulic quick coupler unlock pilot light The hydraulic quick coupler unlock pilot red light (5) is ON and the buzzer sounds when the activation switch of the hydraulic quick coupling system is turned ON.
Page 85 3 - CONTROLS AND INSTRUMENTS 8. Engine pre-heat pilot light When the weather temperature is below 10 °C (50 °F) and the starter switch is turned in ON, the engine pre-heat orange pilot light (8) is ON. SMIL19MEX0731AA 9. Overload warning light The overload warning red light (9) is ON when the ma- chine is overloaded.
Page 86 3 - CONTROLS AND INSTRUMENTS 12. Menu button Press the button (12) to show the next display on the main display. SMIL19MEX0731AA 13. Enter and buzzer stop button Press the button (13) to select the menu. Press the button (13) to stop the buzzer when the buzzer sounds.
Page 87: Air Conditioning Control
3 - CONTROLS AND INSTRUMENTS Air conditioning control SMIL16MEX2336FB (1) Fan switch (3) Outlet control louver (air conditioner only) (2) Temperature control switch 3-29...
Page 88 3 - CONTROLS AND INSTRUMENTS Fan switch The fan switch (1) controls the fan velocity with four steps: • OFF • Low • Medium • High SMIL16MEX2337AA Temperature control switch The temperature control switch (2) controls the tempera- ture of the air blown from the outlet control louver. To decrease the air temperature, turn clockwise the tem- perature control switch.
Page 89: Ventilation And Heating
3 - CONTROLS AND INSTRUMENTS Ventilation and heating SMIL19MEX0789FB The heater switch (1) activates two different speeds of ventilation. The first step activates the low fan speed of ventilation. The second step activates the high fan speed of ventila- tion. The outlet control louvers (2), if open, allows you to control the direction of air.
Page 90 3 - CONTROLS AND INSTRUMENTS The heater use a valve to cut off hot coolant flow to the heater heat exchanger during summer operation. For win- ter operation you have to open the valve to get hot coolant to circulate through the heater core. A = winter position B = summer position NOTE: turn the heater valve clockwise to close the valve.
Page 91: Rearward Controls
3 - CONTROLS AND INSTRUMENTS Rearward controls Storage compartment Located below the operator's seat, this compartment is used to store various objects. Lock and unlock the storage compartment with the starter key. NOTE: for the canopy version, there is a storage compart- ment located behind the operator's seat.
Page 92: Overhead Controls
3 - CONTROLS AND INSTRUMENTS Overhead controls Cab internal lighting The room light (A) can turn ON and OFF as you open and close the door. The room light selection switch is equipped to select either one of the following status: •...
Page 93: Radio
3 - CONTROLS AND INSTRUMENTS Radio SMIL17MEX3035FA (1) Power and volume knob (7) UP/DOWN track buttons (2) Audio selection knob, file search and (SEL) button (8) USB function (3) MODE button / Audio mute / Radio button (9) Auxiliary (AUX IN) function (4) UP/DOWN radio seek buttons (10) Liquid Crystal Display (LCD) screen (5) Pre-set memory buttons...
Page 94 3 - CONTROLS AND INSTRUMENTS General Area selection To select an area, press and hold related buttons at FM1 band for about 3 seconds. • USA Area: press and hold MODE (3) and 1DIS (5) but- tons for 3 s. •...
Page 95 3 - CONTROLS AND INSTRUMENTS Clock adjustment With CLOCK ON selected, press button (A) again af- ter CLOCK ON display, the hour will blink, turn knob (A) right-hand or left-hand to adjust hour. Simply press button (A) again, the minute will blink, turn knob (A) to adjust minute.
Page 96 3 - CONTROLS AND INSTRUMENTS BALANCE control To adjust the left-hand/right-hand speaker balance, first select the BALANCE mode by pressing the SEL button (A) until the BAL indication appears on the LCD screen (B). Within 5 s of choosing the BALANCE mode, turn the se- lection knob (B) right-hand/left-hand to adjust the BAL- ANCE as desired.
Page 97 3 - CONTROLS AND INSTRUMENTS Beep control To adjust the BEEP control, first select the BEEP mode by pressing the button (A) repeatedly until the BEEP indication appears on the LCD screen (B). Turn the selection knob (A) right-hand/left-hand to se- lect the activate BEEP 2ND or BEEP ON or deactivate BEEP OFF.
Page 98 3 - CONTROLS AND INSTRUMENTS (4) UP/DOWN radio seek buttons To automatically select a radio station, momentarily press the up tune seek button (A) or down tune seek button (B). SMIL17MEX2806AA (5) Pre-set memory buttons 1. Pre-set memory button 1, DISP ID3 v2 display 2.
Page 99 3 - CONTROLS AND INSTRUMENTS (6) Pre-set scan (SCAN) / Best Station Mem- ory (BSM) button Pre-set scan (SCAN). Press the SCAN button (A) momentarily to scan the 6 pre-set station stored the memories on each band (AM/FM). The unit will stop at each pre-set station (the pre-set number on the LCD screen will flash during pre-set scan operation) and remain on the selected frequency.
Page 100 3 - CONTROLS AND INSTRUMENTS USB player (8) USB function Open the cover (A) of the USB port, connect a USB device and push the MODE button (B) to switch the USB mode if you want to listen to MP3 files stored in a USB device. The radio will play automatically MP3 files in the USB de- vice while the LCD screen will show “READING USB”.
Page 101 3 - CONTROLS AND INSTRUMENTS MP3 directory/file searching The DIR- button (A) and the DIR+ button (B) are used to select a particular directory and file. Press simply DIR- / DIR+ buttons to select the previous / next directory (if available in the device). Turn right-hand / left-hand the selection knob (C) to search the directory.
Page 102 3 - CONTROLS AND INSTRUMENTS File scan (SCAN) During USB play, press SCAN button (A) to play the first 10 s of each track. When a desired file is reached, press SCAN button (A) again to cancel the function. The unit will then play the selected file. NOTE: in case of playing MP3 file, when the SCAN button is pressed and held for longer than 2 s, the SCAN mark will blink on the LCD screen and all files in the selected...
Page 103 3 - CONTROLS AND INSTRUMENTS (9) Auxiliary function (AUX IN) If you want to listen to music from an external audio de- vice, open the cover (A) of the AUX IN function, connect the external audio device using the AUX cable 3,5 mm an push the MODE button (B) to switch the AUX IN mode.
Page 104: Exterior Controls
3 - CONTROLS AND INSTRUMENTS Exterior controls Side doors WARNING Moving parts! Make sure all entry and mechanical access doors are properly closed before operating the machine. Failure to comply could result in death or serious injury. W0238A Side hood The side hood (A) allows to access to the compartment including the hydraulic oil tank, the fuel tank, the filling plug of the radiator coolant, and the battery disconnect...
Page 105 3 - CONTROLS AND INSTRUMENTS Opening 1. Use the starter key to unlock the engine door. 2. Use the hook to gently lift up the hood and use the lifting stem (1) to secure the hood. NOTICE: while lifting the hood, make sure the hood does not contact the cab.
Page 106: Rear View Mirrors
3 - CONTROLS AND INSTRUMENTS Rear view mirrors WARNING Avoid injury and/or machine damage! Keep the mirrors clean and properly adjusted. Failure to comply could result in death or serious injury. W1078A Left-hand side mirror Position the mirror (A) on the bracket (B) as shown in the figure aside.
Page 107 3 - CONTROLS AND INSTRUMENTS Right-hand side mirror Position the mirror (D) on the bracket (E) as shown in the figure aside. Horizontally adjust the mirror location in order to maximize visibility. The mirror inclination depends on the height both of the seat and the operator.
Page 108: Battery Disconnect Switch
3 - CONTROLS AND INSTRUMENTS Battery disconnect switch NOTICE: never turn the battery disconnect switch to (O) position with the engine running. This could damage the electrical system. NOTICE: never turn the battery disconnect switch to (O) position within 3 min after the starter key is turned off. The machine control system and the engine control system will be damaged.
Page 109: Fuel Tank
3 - CONTROLS AND INSTRUMENTS Fuel tank WARNING Fire hazard! When handling diesel fuel, observe the following precautions: 1. Do not smoke. 2. Never fill the tank when the engine is running. 3. Wipe up spilled fuel immediately. Failure to comply could result in death or serious injury. W0099A Use the starter key to unlock the door (1) located in the upper part of the side hood.
Page 110 3 - CONTROLS AND INSTRUMENTS You can also gain access to the fuel tank (4) by opening the side hood. Use the starter key to unlock the side hood. Use suitable fuel. NOTE: clean around the fuel cap (3) before refueling and do not remove the filter in the neck of the fuel tank.
Page 111: Operating Instructions
4 - OPERATING INSTRUCTIONS 4 - OPERATING INSTRUCTIONS###_4_### Starting the unit Anti-theft protection Engine Starting Limit (ESL) mode setting ESL mode is designed to be a theft deterrent and prevent the unauthorized operation of the machine. If the ESL mode is selected in “Always” mode, the password is required when the starter switch is turned •...
Page 112 To change the password, input 5 to 10 digits and press Enter. 1. Delete 2. Enter NOTE: the default password is 00000 NOTICE: If the operator forgot or lost the password con- tact your authorized NEW HOLLAND CONSTRUCTION dealer. SMIL16MEX0384AA...
Page 113: Starting The Engine
4 - OPERATING INSTRUCTIONS Starting the engine WARNING Avoid injury! Before starting the engine, securely fasten the seat belt. The seat belt can help ensure your safety if it is properly used and maintained. Never wear a seat belt loosely or with slack in the belt system. Never wear the belt if it is twisted or pinched between the seat structures.
Page 114 4 - OPERATING INSTRUCTIONS 8. After two seconds, check that all the lights on the in- strument cluster turn OFF, except the engine oil pres- sure warning light (4) and the battery charging warning light (5). 9. If the ESL mode is set to the Always, enter the pass- word to start the engine.
Page 115: Bringing The Machine Up To Operating Temperature
4 - OPERATING INSTRUCTIONS Bringing the machine up to operating temperature Before starting operation, allow the main systems to warm up to their normal operating temperature. NOTE: the normal operating temperature for the hydraulic fluid is 50 – 80 °C (122 – 176 °F). NOTICE: do not operate the machine if the temperature of the hydraulic fluid is below 25 °C (77 °F).
Page 116: Operating The Machine In Hot Or Cold Weather
4 - OPERATING INSTRUCTIONS Operating the machine in hot or cold weather In cold weather • Make sure to use fluids and lubricants which have specifications suitable for operation at low ambient temperatures. • Check the batteries for full charge state. •...
Page 117: Operating The Machine
4 - OPERATING INSTRUCTIONS Operating the machine WARNING Misuse hazard! Follow the operating instructions in this chapter. Any other practice that has not received the prior approval of the manufacturer is considered to be strictly forbidden. Failure to comply could result in death or serious injury. W0281A WARNING Hazard to bystanders!
Page 118 4 - OPERATING INSTRUCTIONS Normal operation of the machine When rolling in the arm, the roll-in movement stops mo- mentary at point (X) as shown, then recovers speed again after passing point (X). The reason is that the movement by the arm weight is faster than the speed of oil flow into the cylinder.
Page 119 4 - OPERATING INSTRUCTIONS Operating the machine on sloping ground WARNING Driving hazard! Hillside operations can be dangerous. Rain, snow, ice, loose gravel, or soft ground, etc. can change the ground conditions. You must make a judgment if it is safe to operate your machine on any hillside or ramp.
Page 120 4 - OPERATING INSTRUCTIONS Digging and loading operations Set the tracks parallel to the line of the ditch to be excavated when digging a ditch. Do not swing while digging. 1. Do the digging work by arm. Use the pulling force of arm for digging and use together with the digging force of the bucket if necessary.
Page 121: Lowering The Attachment In The Event Of A Failure
4 - OPERATING INSTRUCTIONS Lowering the attachment in the event of a failure WARNING Unexpected machine movement! Only use the following procedure in case of machine failure. Always use extreme caution during oper- ations. Keep other persons away from the bucket, attachment, and boom. The bucket or attachment can move unexpectedly during operations due to weight of the bucket, attachment, arm, or boom.
Page 122: Bucket Replacement
4 - OPERATING INSTRUCTIONS Bucket replacement WARNING Flying object! Always wear eye or full face protection when performing this procedure. Failure to comply could result in death or se- rious injury. W0313A 1. Lower the bucket to the ground. NOTE: place the bucket in light contact with the ground.
Page 123: Hydraulic Control Lever Operating Pattern
4 - OPERATING INSTRUCTIONS Hydraulic control lever operating pattern WARNING Unexpected machine movement! Pilot controls have two different machine control patterns. Before you operate the machine, check which pattern is active. Failure to comply could result in death or serious injury. W1577A NOTICE: before starting the machine, make sure about the position of the lever of the machine control pattern...
Page 124 4 - OPERATING INSTRUCTIONS WARNING Avoid injury! Inspect the work area or job site to make sure that machine operation can be done safely. Confirm that the lever operation is the same as indicated on the control pattern labels. If not, immediately change the machine control pattern or the label displayed to match the ma- chine control pattern.
Page 125 4 - OPERATING INSTRUCTIONS Pattern: SAE type Left–hand control lever control function 1. Boom lowering 2. Boom raising 3. Swing left-hand 4. Swing right-hand SMIL16MEX3077AB Right–hand control lever control function 5. Arm out 6. Arm in 7. Bucket in 8. Bucket out SMIL16MEX3079AB 4-15...
Page 126: Caution While Using Rubber Tracks
4 - OPERATING INSTRUCTIONS Caution while using rubber tracks Proper usage Rubber belt Less vibration The rubber tracks offer excellent features which steel Smooth operation tracks do not possess. Low noise However, if they are used the same way as the steel Harmless for paved road tracks, then their advantages cannot be fully exploited.
Page 127 4 - OPERATING INSTRUCTIONS Do not let oil, fuel, solvents, etc., come in contact with rubber shoes. If this happens, wipe off tracks with a cloth immediately. LELI11E0261AA Do not enter such hot places as an open-air fire, or a steel plate left in the open sun.
Page 128 4 - OPERATING INSTRUCTIONS Use care so that the bucket does not damage the rubber track while working. Do not move the machine pressing the bucket against a concrete surface or walls. Lower the machine slowly, if it had previously been lifted by means of the attachment.
Page 129 4 - OPERATING INSTRUCTIONS If you travel on a slope with the machine higher at one side, this will risks to damage the rubber track. Both ma- chine sides must travel at the same level. LELI11E0269AB Do not change the direction of the machine with the rubber tracks positioned on earth heaps, as this could cause the rubber track to come off or get damaged.
Page 130: Stopping The Unit
4 - OPERATING INSTRUCTIONS Stopping the unit Stopping the engine 1. Lower the attachment until it is resting on the ground. 2. Set the safety lever backward (LOCK position). 3. Set the engine speed lever to low idle position and let the engine run for about 5 min.
Page 131: Moving The Unit
4 - OPERATING INSTRUCTIONS Moving the unit Machine travel WARNING Controls can be reversed! In the normal travel position, the operator's compartment is above the idler wheels and the travel reduction gears are to the rear of the upper structure. If the upper structure is turned 180 degrees in relation to the undercarriage, the controls are reversed.
Page 132 4 - OPERATING INSTRUCTIONS Straight line travel (forward travel) Press the two pedals (or push the two levers) forward at the same time. SMIL13CEX2679AB Straight line travel (reverse travel) Press the two pedals (or pull the two levers) rearwards at the same time.
Page 133 4 - OPERATING INSTRUCTIONS Turning to the left (reverse travel) Press the right-hand pedal or pull the right-hand lever rearwards. SMIL13CEX2683AB Turning to the right (reverse travel) Press the left-hand pedal or pull the left-hand lever rear- wards. SMIL13CEX2684AB Turning on the spot, to the right Press the left-hand pedal or push the left-hand lever for- wards and at the same time press the right-hand pedal or pull the right-hand lever rearwards.
Page 134 4 - OPERATING INSTRUCTIONS Gradual turn on the move Press one of the pedals or push one of the levers and, at the same time, press the other pedal or push the other lever in the same direction, but slightly harder. Stopping travel To come to a complete halt, release the levers or pedals and they will return to neutral.
Page 135 4 - OPERATING INSTRUCTIONS Precautions for travelling on slopes When traveling on a sloping ground, the machine be- comes unstable, unbalanced, and difficult to control. Therefore, the following operating prescriptions shall be strictly respected. Always travel with the undercarriage oriented along the slope, never across.
Page 136 Block both tracks by means of wedges (3), and de- fine a safe area of at least 3 m (9.8 ft) around the ma- chine, cleaning this area from obstacles and bystanders. Call the NEW HOLLAND CONSTRUCTION dealer for as- sistance. SMIL18MEX0137AB...
Page 137: Parking The Unit
4 - OPERATING INSTRUCTIONS Parking the unit Parking the machine WARNING Fall hazard! Jumping on or off the machine could cause an injury. Always face the machine, use the handrails and steps, and get on or off slowly. Maintain a three-point contact to avoid falling: both hands on the handrails and one foot on the step, or one hand on the handrail and both feet on the steps.
Page 138 Block both tracks by means of wedges, and define a safe area of at least 3 m (9.8 ft) around the machine, cleaning this area from obstacles and bystanders. Call the NEW HOLLAND CONSTRUC- TION dealer for assistance. LELI11E0243AA...
Page 139: Transport Operations
5 - TRANSPORT OPERATIONS 5 - TRANSPORT OPERATIONS###_5_### Road transport Loading the machine onto a transport trailer WARNING Improper operation or service of this machine can result in an accident. Assign a supervisor to direct worksite operations. Agree on all safety measures, procedures, and suitable hand signals.
Page 140 5 - TRANSPORT OPERATIONS Loading the machine on a rear loading type trailer 1. Align the machine to the trailer, so as the travel motors are in the rear. 2. Slowly travel on the trailer bed to reach the resting position, giving particular attention to the attachment so as not to touch the trailer bed.
Page 141: Preparing For Road Transport
5 - TRANSPORT OPERATIONS Preparing for road transport Tie downs for shipping Set the machine in the position for transport: fully retract the arm and curl the bucket slowly. Lower the dozer blade. Check the overall height between the ground and the highest point of the machine and check the overall width of the machine.
Page 142: Unloading The Machine From A Transport Trailer
5 - TRANSPORT OPERATIONS Unloading the machine from a transport trailer Rear loading type transport trailer 1. Position the trailer on firm and level ground. Put blocks at the tires of trailer to prevent trailer from moving. 2. Remove wire ropes, chocks, blocks and other devices used to secure the machine during road transport.
Page 143: Shipping Transport
5 - TRANSPORT OPERATIONS Shipping transport Handling the machine WARNING Improper operation or service of this machine can result in an accident. Assign a supervisor to direct worksite operations. Agree on all safety measures, procedures, and suitable hand signals. Failure to comply could result in death or serious injury. W0287A WARNING Crushing hazard!
Page 144 5 - TRANSPORT OPERATIONS 1. Check the weight, length, width and height of the ma- chine referring to the chapter 2, specification when you are going to hoist the machine. 2. Use long wire rope and stay to keep the distance with the machine as it should avoid touching with the ma- chine.
Page 145: Recovery Transport
Failure to comply could result in death or serious injury. W0259A As far as possible try to carry out repairs on spot or consult your NEW HOLLAND CONSTRUCTION Dealer. NOTICE: the machine must be towed very slowly, over a short distance and only if it is really unavoidable. Always tow the machine in alignment with the undercarriage.
Page 146 5 - TRANSPORT OPERATIONS...
Page 147: Maintenance
NOTICE: be sure all the service operations in this section are carried out punctually at the intervals given, in order to ensure optimum performance levels and maximum safety when using the machine. NOTICE: while any company can perform necessary maintenance or repairs on your equipment, NEW HOLLAND CONSTRUCTION strongly recommends that you use only authorized NEW HOLLAND CONSTRUCTION dealers and products that meet given specifications.
Page 148 6 - MAINTENANCE NOTE: oil and fluid should not be thrown on the ground. They must be stored and removed by a company which is responsible for their recycling or their disposal. Hourmeter The hourmeter enables service operations to be sched- uled.
Page 149 6 - MAINTENANCE Attachment • Check that the cylinders are not leaking oil. • Check the condition of all lines. • Check the condition of the bucket teeth. After starting the engine • Did the engine start correctly? Are the exhaust fumes normal? Any strange noises? •...
Page 150: General Specifications - Biodiesel Fuels
Cold Pressed Oil, Straight Vegetable Oil (SVO), or more fuels. generally unrefined vegetable oils used as motor fuel are NOT APPROVED at any blend in any NEW HOLLAND NOTICE: Never use biodiesel blends higher than B7. CONSTRUCTION product. Biodiesel fuel has several positive features in comparison...
Page 151 NOTICE: Biodiesel is highly hygroscopic and tends to col- conditions for biodiesel fuel handling and maintenance lect water more than diesel fuel. This increases the risk of will not be covered for Warranty by NEW HOLLAND CONSTRUCTION. algae and bacteria growth which can cause severe dam- age to the fuel injection system.
Page 152: Fluids And Lubricants
NOTICE: using any lubricating oils other than NEW HOLLAND CONSTRUCTION genuine products may lead to a deterioration of performance and cause damage to major components. NOTICE: do not mix NEW HOLLAND CONSTRUCTION genuine oil with any other lubricating oil as it may result in demage to the systems of major components.
Page 153 6 - MAINTENANCE Engine coolant NEW HOLLAND CONSTRUCTION requires the use of a fully formulated Organic Acid Technology (OAT) based coolant. OAT E is the reference genuine product. XTENDED OOLANT NTIFREEZE NOTICE: use of different coolant brands is not recommended.
Page 154 For North America only: during cold weather, lower than -7 °C (19.4 °F), it is temporarily acceptable to use a mixture of No. 1-D (S15) and No. 2-D (S15). NOTICE: if operating in severe winter climate, consult the fuel supplier or the NEW HOLLAND CONSTRUCTION dealer for specific diesel fuel to be used.
Page 155 NOTE: for example, make sure that the receptacle for collecting oil to be replaced is not leaking. Never spread fluids or lubricants on the ground or into water. Consult the NEW HOLLAND CONSTRUCTION dealer or the Local Environmental Agency in order to obtain information on the correct method of disposing fluids and lubricants used on the machine.
Page 156: Releasing Pressure In The Hydraulic System
6 - MAINTENANCE Releasing pressure in the hydraulic system WARNING Pressurized system! System is still under pressure. Release pressure according to instructions in this manual. Failure to comply could result in death or serious injury. W1044A 1. Place the machine on a flat and level ground. Lower the attachment to the ground and stop the engine.
Page 157 6 - MAINTENANCE 5. Operate the dozer blade control lever a dozen times approximately. NOTE: this procedure does not completely release the pressure, so when operate on the hydraulic system, loosen the connections slowly and do not stand in the direction where the oil drains out.
Page 158 6 - MAINTENANCE Auxiliary hydraulic circuits – pressure release First and second auxiliary hydraulic circuits are high pressure hydraulic systems. Always release the pressure before connecting or disconnecting the hydraulic hoses between the machine and the attachment. 1. Place the machine on a flat and level ground. Lower the attachment to the ground and stop the engine.
Page 159 6 - MAINTENANCE 5. Otherwise, if the machine is equipped with the propor- tional switch on the right-hand control lever, slide it to left-hand and right-hand three times approximately to release the pressure. NOTE: this procedure does not completely release the pressure, so when operate on the hydraulic system, loosen the connections slowly and do not stand in the direction where the oil drains out.
Page 160 6 - MAINTENANCE 7. If the machine is equipped with the angle blade control lever operate the lever from front to rear a dozen times approximately and move the slider to left-hand and right-hand three times approximately to release the pressure.
Page 161: Fuel System Bleeding
6 - MAINTENANCE Fuel system bleeding In the following cases, drainage from the fuel system is required: • The tank has become empty completely. • The fuel filter is replaced. • The components of the fuel system are removed for service or repair.
Page 162: Protecting The Electronic And Electrical Systems During Battery Charging Or Welding
6 - MAINTENANCE Protecting the electronic and electrical systems during battery charging or welding DANGER Improper operation or service of this machine can result in an accident. Any unauthorized modifications made to this machine can have serious consequences. Consult an authorized dealer on changes, additions, or modifications that may be required for this machine.
Page 163: Maintenance Planning
6 - MAINTENANCE Maintenance planning Maintenance chart Grease Drain fluid Replace Adjust Change fluid Cleaning Check Charging Maintenance action Page no. Break-in period Tightening torques 6-19 Engine oil and filter 6-19 Fuel filter 6-19 Hydraulic oil return filter 6-19 Pilot line filter 6-19 Travel reduction gears 6-19...
Page 164 6 - MAINTENANCE Grease Drain fluid Replace Adjust Change fluid Cleaning Check Charging Maintenance action Page no. Hydraulic hoses 6-62 Valve seat 6-62 Injection timing 6-62 Injection pump 6-62 Biodegradable hydraulic oil 6-63 Every 5000 hours Hydraulic oil 6-65 When necessary Cab and working lights 6-67 6-70...
Page 165: Break-In Period
6 - MAINTENANCE Break-in period Tightening torques Check the tightening torques after the first 50 h of ser- vice, then check the tightening torques every 250 h. To check the tightening torques, see page 6-43. Engine oil and filter Replace the engine oil and the engine oil filter after the first 250 h.
Page 166: Boom Swing Cylinder
6 - MAINTENANCE Boom swing cylinder Grease the boom swing cylinder every 10 h within the first 50 h, then grease every 250 h. To grease the boom swing cylinder refer to page Boom swing cylinder. Grease points (Bucket) Lubricate the bucket linkage (arm-bucket connection and arm-bucket link connection) and the bucket cylin- der pin (rod side) every 10 h within the first 50 h, then lubricate every 50 h.
Page 167: Every 10 Hours
6 - MAINTENANCE Every 10 hours Engine oil level Check the engine oil level every 10 h or every day. Lubricant: E 15W-40 NGINE 1. Park the machine on a flat and level place. Stop the engine, and remove the starter key. 2.
Page 168: Engine Coolant Level
6 - MAINTENANCE Engine coolant level WARNING Hazardous chemicals! Coolant can be toxic. Avoid contact with skin, eyes, and clothing. Antidotes: EXTERNAL - Rinse thoroughly with water. Remove soiled clothing. INTERNAL - Rinse the mouth with water. DO NOT induce vomiting. Seek immediate medical attention. EYES - Flush with water.
Page 169: Hydraulic Oil Level
6 - MAINTENANCE Hydraulic oil level WARNING Burn hazard! Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F). Failure to comply could result in death or serious injury. W0241A Check the hydraulic oil level every 10 h or every day Fluid: P...
Page 170: Fuel Filter Water Separator
6 - MAINTENANCE Fuel filter water separator Drain water and sediment from the fuel filter water separator every 10 h or every day. Clean the filter element of the fuel filter water separator every 200 h. Drain water 1. Open the engine hood to access to the fuel filter water separator and place a container with an appropriate capacity under the fuel filter water separator (1).
Page 171: Fan And Alternator Drive Belt
6 - MAINTENANCE Fan and alternator drive belt Inspection of fan Inspect the fan every 10 h or every day. Perform a visual inspection of the fan every 10 h or ev- ery day. Check for cracks, loose rivets, and bent or loose blades.
Page 172 6 - MAINTENANCE 2. Tighten the belt to the proper tension. There must be clearance (1) between the belt and the bottom of the pulley groove. If there is no clearance (2) between the belt and the bottom of the pulley groove, replace the belt.
Page 173: Air-Conditioning Compressor Drive Belt
6 - MAINTENANCE Air-conditioning compressor drive belt Check the air-conditioning compressor drive belt tension every 10 h or every day. Adjustment of tension 1. To adjust the tension of the V-belt (1) use the belt ten- sion gauge indicated in figure. 2.
Page 174: Every 50 Hours
6 - MAINTENANCE Every 50 hours Grease points (Bucket) Grease the bucket linkage every 50 h (after the break-in period). Lubricant: M NGLI-2 ULTI URPOSE REASE XTREME PRESSURE AND ANTI WEAR SMIL18MEX0144FA Bucket cylinder pin (rod side): one grease fitting Bucket link (control rod): one grease fitting Arm and bucket connection pin: one grease fitting Arm and control link connection pin: one grease fitting...
Page 175: Grease Points (Blade)
6 - MAINTENANCE Grease points (Blade) Grease the blade every 50 h (after the break-in period). Lubricant: M NGLI-2 ULTI URPOSE REASE XTREME PRESSURE AND ANTI WEAR SMIL18MEX0144FA Standard version Dozer blade connection pin: three grease fittings Dozer blade cylinder pin: two grease fittings NOTICE: if you operate the machine in water or mud, you must lubricate the dozer blade connection pin and the dozer blade cylinder pin every 10 h.
Page 176 6 - MAINTENANCE SMIL18MEX0145FA Angle blade version Dozer angle blade cylinder pin (if equipped): two grease fittings NOTICE: if you operate the machine in water or mud, you must lubricate the dozer blade connection pin and the dozer blade cylinder pin every 10 h. 6-30...
Page 177: Swing Ring Gear
6 - MAINTENANCE Swing ring gear Grease the swing ring gear every 50 h. Lubricant: M NLGI 2 ULTI URPOSE REASE XTREME RESSURE AND ANTI WEAR Swing ring gear: one grease fittings Using a grease gun, inject grease of the specified type in the grease points shown in figure.
Page 178: Track Tension
6 - MAINTENANCE Track tension WARNING Tip-over hazard! Only raise the track as little as necessary. Failure to comply could result in death or serious injury. W0276A Check the track tension every 50 h NOTICE: if the tracks are too tight, they wear quickly. If tracks are not tight enough, they wear quickly and can catch on the sprocket wheel or slide off the idler wheel or the sprocket wheel.
Page 179 6 - MAINTENANCE Adjusting the tension To increase the tension: 1. Clean the grease fitting adapter and the grease fitting. 2. Connect the grease pump. Inject the grease to obtain the right amount of track tension. 3. Remove the grease pump and clean the grease fitting.
Page 180: Fuel Tank Drain
6 - MAINTENANCE Fuel tank drain WARNING Fire hazard! When handling diesel fuel, observe the following precautions: 1. Do not smoke. 2. Never fill the tank when the engine is running. 3. Wipe up spilled fuel immediately. Failure to comply could result in death or serious injury. W0099A Drain water and sediment from the fuel tank every 50 h.
Page 181: Every 100 Hours
6 - MAINTENANCE Every 100 hours Fuel filter water separator Drain water and sediment from the fuel filter water separator every 10 h or every day. Clean the filter element of the fuel filter water separator every 200 h. 1. Open the engine hood to access to the fuel filter water separator and place a container with an appropriate capacity under the fuel filter water separator (1).
Page 182 6 - MAINTENANCE Priming the fuel system 1. Turn the starter switch to ON position for 10 – 15 s. The electric fuel pump prime the fuel system. NOTE: never use the starter motor to crank the engine in order to prime the fuel system. This may cause the starter motor to overheat and damage the coils, the pinion and/or the ring gear.
Page 183: Every 250 Hours
6 - MAINTENANCE Every 250 hours Battery WARNING Improper operation or service of this machine can result in an accident. Before working on any component(s) of the electrical circuit, put the ignition key in the off (shut down) position. When disconnecting batteries, always disconnect the negative (-) cable first. When recon- necting batteries, always connect the negative (-) cable last.
Page 184 6 - MAINTENANCE Cleaning of the battery 1. Wash the terminal with hot water, and apply grease to the terminals after washing. SMIL16MEX2521AB Battery voltage check NOTICE: if the machine is to be operated for a short time without battery (using a slave battery for starting), use additional current (lights) while engine is running and insulate terminal of battery.
Page 185 6 - MAINTENANCE Starting the engine with booster cable WARNING Improper operation or service of this machine can result in an accident. An error connecting auxiliary starting cables or short-circuiting battery terminals can cause an acci- dent. Connect auxiliary starting cables as instructed in this manual. Failure to comply could result in death or serious injury.
Page 186: Swing Bearing
6 - MAINTENANCE Swing bearing Grease the swing bearing every 250 h. Lubricant: M NLGI 2 ULTI URPOSE REASE XTREME RESSURE AND ANTI WEAR Swing bearing: one grease fittings Using a grease gun, inject grease of the specified type in the grease points shown in figure. SMIL19MEX0723AA Swing bearing greasing point SMIL18MEX0756AA...
Page 187: Boom Swing Cylinder
6 - MAINTENANCE Boom swing cylinder Grease the boom swing cylinder every 250 h (after the break-in period). Lubricant: M NGLI-2 ULTI URPOSE REASE XTREME PRESSURE AND ANTI WEAR Boom swing cylinder: one grease fitting Using a grease gun, inject grease of the specified type in the grease points shown in figure.
Page 188: Grease Points (Boom And Arm)
6 - MAINTENANCE Grease points (Boom and arm) Grease the boom, the arm, the bucket cylinder pin (head side), and the boom swing post every 250 h (after the break-in period). Lubricant: M NGLI-2 ULTI URPOSE REASE XTREME PRESSURE AND ANTI WEAR SMIL18MEX0144FA Boom cylinder (head and rod side): two grease fittings...
Page 189: Tightening Torques
6 - MAINTENANCE Tightening torques Check the tightening torques every 250 h (after the break-in period). Component Bolt size Torque setting Engine mounting bolt (engine–bracket) M10 x 1.25 54.2 – 81.3 N·m (40 – 60 lb ft) Engine mounting bolt (bracket-frame) 96.3 –...
Page 190: Every 500 Hours
6 - MAINTENANCE Every 500 hours Engine oil and filter Replace the engine oil and the engine oil filter every 500 h (after the break-in period). Lubricant: E 15W-40 NGINE Quantity: 6.7 L (1.8 US gal) NOTICE: if engine is used with High Sulfur Fuel [ 0.05% ( 500 ppm) ≤ Sulfur Content ≤ 0.5% ( 5000 ppm)], change the engine oil at shorter intervals (approximately half).
Page 191 6 - MAINTENANCE 7. Attach a new filter. Turn the filter until the seal touches the filter head, and then tighten it further a half turn by hand. NOTE: do not use a filter wrench for tightening the filter. Overtightening can damage the filter and its seal. A.
Page 192: Fuel Filter
6 - MAINTENANCE Fuel filter WARNING Fire hazard! When handling diesel fuel, observe the following precautions: 1. Do not smoke. 2. Never fill the tank when the engine is running. 3. Wipe up spilled fuel immediately. Failure to comply could result in death or serious injury. W0099A Replace the fuel filter element every 500 h (after the break-in period).
Page 193 6 - MAINTENANCE A. OUT (to the fuel injector pump) B. IN (from the fuel injector pump) C. IN (from the fuel feed pump) D. OUT (to the fuel tank) SMIL18MEX0534BA 4. Remove the fuel filter (1) with a filter wrench, turning it to the left.
Page 194: Air Cleaner
6 - MAINTENANCE Air cleaner CAUTION Flying debris! Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using com- pressed air. Failure to comply could result in minor or moderate injury. C0049A Clean the air filter every 500 h or when the “air cleaner warning light” appears on the instrument cluster.
Page 195 NOTE: do not use compressed air if there is oil or soot in the element. If the cartridge is greasy: Clean it in water, with suitable detergent. (Consult your NEW HOLLAND CONSTRUCTION dealer). Instructions for using the detergent are printed on the package. NOTE: dry the element out completely before installing it.
Page 196 6 - MAINTENANCE Inspecting the element Check the element for damage by placing an inspection light inside the element. NOTE: change the element if light can be seen through a hole, however small. SMIL16MEX0434AA 6. Remove the secondary element (5). NOTE: the secondary element (5) cannot be cleaned and must be changed.
Page 197: Radiator And Coolers
Blow the air in the opposite direction of the fan air flow. NOTICE: in presence of greasy or oily dust, consult your NEW HOLLAND CONSTRUCTION dealer in order to carry out a special cleaning operation. NOTICE: use compressed air pressure of maximum 550 kPa (79.8 psi).
Page 198: Every 1000 Hours
6 - MAINTENANCE Every 1000 hours Hydraulic oil return filter WARNING Burn hazard! Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F). Failure to comply could result in death or serious injury. W0241A WARNING Pressurized system!
Page 199: Pilot Line Filter
6 - MAINTENANCE Pilot line filter WARNING Burn hazard! Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F). Failure to comply could result in death or serious injury. W0241A WARNING Pressurized system!
Page 200: Travel Reduction Gears
Check the valve clearance every 1000 h. NOTICE: to check the valve clearance refer to your NEW HOLLAND CONSTRUCTION dealer. Injection nozzle Check the injection nozzle pressure every 1000 h. NOTICE: to check the injection nozzle pressure refer to your NEW HOLLAND CONSTRUCTION dealer. 6-54...
Page 201: Every 2000 Hours
6 - MAINTENANCE Every 2000 hours Air cleaner Replace the air cleaner every 2000 h. 1. Open the engine access door to access to the air cleaner (1). SMIL16MEX1533BA 2. Unlock the two fasteners (1). SMIL16MEX1529AA 6-55...
Page 202 6 - MAINTENANCE 3. Remove the cover (2) of the air cleaner (3). SMIL16MEX1530AA 4. Remove the primary element (4). SMIL16MEX1531AA 5. Remove the secondary element (5). NOTE: the secondary element (5) cannot be cleaned and must be changed. SMIL16MEX1532AA 6.
Page 203 6 - MAINTENANCE 8. Lock the two fasteners (2). NOTICE: the air flow sensor is installed on the inlet duct of the air cleaner. Pay attention not to allow dust to enter the inlet duct when replacing the air cleaner element. SMIL16MEX1529AA 6-57...
Page 204: Engine Coolant
6 - MAINTENANCE Engine coolant WARNING Hazardous chemicals! Coolant can be toxic. Avoid contact with skin, eyes, and clothing. Antidotes: EXTERNAL - Rinse thoroughly with water. Remove soiled clothing. INTERNAL - Rinse the mouth with water. DO NOT induce vomiting. Seek immediate medical attention. EYES - Flush with water.
Page 205 6 - MAINTENANCE 4. Open the valve heater (only for cab version). 5. Drain the engine coolant by opening the drain plug. Use a wrench 17 mm 6. Tighten the drain plug to 18 – 22 N·m (13 – 16 lb ft) NOTICE: after draining coolant, do not start the engine with no water in the radiator.
Page 206 6 - MAINTENANCE Flushing the system 8. Fill the system with a mixture of sodium carbonate and water (or a commercially available equivalent). NOTE: use 0.5 kg (1.1 lb) of sodium carbonate for every 23 L (6.1 US gal) of water. 9.
Page 207: Hydraulic Oil Suction Filter
6 - MAINTENANCE Hydraulic oil suction filter WARNING Burn hazard! Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F). Failure to comply could result in death or serious injury. W0241A WARNING Pressurized system!
Page 208: Hydraulic Hoses
Valve seat Adjust the valve seat every 2000 h. NOTICE: to adjust the valve seat refer to your NEW HOLLAND CONSTRUCTION dealer. Injection timing Check the injection timing every 2000 h. NOTICE: to check the injection timing refer to your NEW HOLLAND CONSTRUCTION dealer.
Page 209: Biodegradable Hydraulic Oil
6 - MAINTENANCE Biodegradable hydraulic oil WARNING Burn hazard! Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F). Failure to comply could result in death or serious injury. W0241A WARNING Pressurized system!
Page 210 6 - MAINTENANCE 3. Open the side hood and loosen the filling cap. SMIL16MEX1471BA 4. Place a container with a capacity of 40 L (10.6 US gal) under the drain plug. Loosen the drain plug at the bot- tom of the hydraulic oil tank. 5.
Page 211: Every 5000 Hours
6 - MAINTENANCE Every 5000 hours Hydraulic oil WARNING Burn hazard! Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F). Failure to comply could result in death or serious injury. W0241A WARNING Pressurized system!
Page 212 6 - MAINTENANCE 3. Open the side hood and loosen the filling cap. SMIL16MEX1471BA 4. Place a container with a capacity of 40 L (10.6 US gal) under the drain plug. Loosen the drain plug at the bot- tom of the hydraulic oil tank. 5.
Page 213: When Necessary
6 - MAINTENANCE When necessary Cab and working lights Cab light 1. Remove the two retaining screws. SMIL16MEX0921AA 2. Extract the ceiling light (1) and pull out the bulb (2). SMIL16MEX0922AA 3. Install a new 5 W bulb in the ceiling light. 4.
Page 214 6 - MAINTENANCE Halogen working lights 1. Remove the two retaining screws. SMIL16MEX0939AA 2. Extract the working light (1) and disconnect the bulb plug (2). SMIL16MEX0935AA 3. Pull the clip outwards (1) and remove the bulb (2). SMIL16MEX0937AA 4. Install a new 55 W bulb in the working light. NOTE: make sure of the correct position of the bulb.
Page 215 6 - MAINTENANCE LED working lights LED lights are located on both the cab (1) and the arm (2) of the machine. SMIL19MEX0279AA SMIL19MEX0278AA To change the LED lights proceed as follows: 1. Disconnect the power connector (1). 2. Loosen the M8 self-locking nut (2) and replace the LED light 11 W (3).
Page 216: Cab Air Filter
6 - MAINTENANCE Cab air filter CAUTION Flying debris! Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using com- pressed air. Failure to comply could result in minor or moderate injury. C0049A Clean the cab heater filter when necessary.
Page 217: Fuel Tank Strainer
6 - MAINTENANCE Fuel tank strainer Clean the fuel tank strainer periodically 1. Remove the fuel cap. 2. Remove the fuel tank strainer located inside the fuel filler neck. 3. Inspect the fuel tank strainer for damage. If damaged, discard and replace. If in good condition, clean it in an environmentally safe manner.
Page 218: Control Levers
6 - MAINTENANCE Control levers Grease the hydraulic control levers when necessary Fluid: M NLGI 2 ULTI URPOSE REASE XTREME RESSURE AND ANTI WEAR 1. Remove the bellow (A) from the control lever. 2. Use a grease gun and grease the joint part (X) and the sliding parts (Y).
Page 219: Air-Conditioning System
6 - MAINTENANCE Air-conditioning system WARNING Avoid chemical burns! Wear protective goggles and non-permeable gloves when working with the fluorescent dye and leak testing an air-conditioning system. Failure to comply could result in death or serious injury. W0918A WARNING Maintenance hazard! Never try to service the air-conditioning system yourself.
Page 220 6 - MAINTENANCE Never charge the cylinders over 80% of maximum ca- pacity. Do not leave the unit powered up if you do not intend to use it immediately. Cut off the mains power supply when it is not planned to use the equipment. Charging of the air-conditioning system 1.
Page 221 6 - MAINTENANCE 7. Charge the system with the quantity of R134 indicated in the air-conditioning decal (1) that you have on your machine. Quantity of R134 : 0.6 kg (1.32 lb) NOTE: the air-conditioning decal (1) is located in the en- gine compartment.
Page 222: Fuse And Relay Locations
6 - MAINTENANCE Fuse and relay locations Fuses To access the fuse box (1), open the door (2) located below the operator's seat. The fuse box cover indicates the function and amper- age of each fuse. NOTICE: before changing fuses or relays, turn the starter key to the OFF position.
Page 223: Preparing For Storage
Lower the dozer blade to the ground. 4. Grease the machine thoroughly. The exposed surfaces of the cylinder rods should be greased or covered with a protective film. Consult your NEW HOLLAND CON- STRUCTION Dealer. NOTE: when the machine resumes service, the film will disappear automatically.
Page 224: Periodic Checks
6 - MAINTENANCE Periodic checks WARNING Inhalation hazard! Risk to operators and bystanders. Avoid running the engine in confined areas. Make sure there is adequate ventilation at all times. Failure to comply could result in death or serious injury. W0156A Every month, check: 1.
Page 225: Starting Up The Machine After Storage
6 - MAINTENANCE Starting up the machine after storage WARNING Unexpected machine movement! Before starting the engine, make sure all controls are in the neutral position. Failure to comply could result in death or serious injury. W0311A WARNING Inhalation hazard! Risk to operators and bystanders. Avoid running the engine in confined areas.
Page 226 6 - MAINTENANCE 6-80...
Page 227: Troubleshooting
Engine - Troubleshooting NOTE: This chapter describes the easy diagnostic methods for engine-related problems and the remedies for them. If you cannot find the cause of a problem or solve a problem, consult the NEW HOLLAND CONSTRUCTION dealer. Problem Possible Cause...
Page 228: Electrical Systems - Troubleshooting
Electrical systems - Troubleshooting NOTE: this chapter describes the easy diagnostic methods for electrical system-related problems and the remedies for them. If you cannot find the cause of a problem or solve a problem, consult the NEW HOLLAND CONSTRUCTION dealer.
Page 229: Other Systems - Troubleshooting
Other systems - Troubleshooting NOTE: this chapter describes the easy diagnostic methods for generic problems and the remedies for them. If you cannot find the cause of a problem or solve a problem, consult the NEW HOLLAND CONSTRUCTION dealer. Problem...
Page 230 7 - TROUBLESHOOTING...
Page 231: Specifications
8 - SPECIFICATIONS SPECIFICATIONS###_9_### Machine specifications Engine Model Yanmar 3TNV88F-ESHYB Type 4-cycle vertical overhead valve, diesel fuel Cooling method Water cooling Number of cylinders and arrangement 3 cylinders, in-line Firing order 1 - 3 - 2 Combustion chamber type Direct injection type Cylinder bore x stroke 88 mm (3.46 in) x 90 mm (3.54 in) Piston displacement...
Page 232 8 - SPECIFICATIONS Swing motor Type Fixed displacement axial piston motor Capacity 22 cm³/rev (1.3 in³/rev) Relief pressure 19616 kPa (2845 psi) Braking system Automatic, spring applied hydraulic released Braking torque 90.2 N·m (66.5 lb ft) Brake release pressure 1958 – 6378 kPa (284 – 925 psi) Reduction gear type 2 - stage planetary Travel motor...
Page 233 8 - SPECIFICATIONS Number of rollers and shoes on each side Upper roller Lower roller Track shoes...
Page 234: Dimensions
8 - SPECIFICATIONS Dimensions Cab version SMIL18MEX0146FA (A) Overall length 4790 mm (188.6 in) (B) Overall width, with 300 mm (11.8 in) shoe 1740 mm (68.5 in) (C) Overall height 2500 mm (98.4 in) (E) Overall height of cab 2500 mm (98.4 in) (F) Ground clearance of counterweight 540 mm (21.3 in) (H) Minimum ground clearance...
Page 235 8 - SPECIFICATIONS Canopy version SMIL18MEX0147FA (A) Overall length 4790 mm (188.6 in) (B) Overall width, with 300 mm (11.8 in) shoe 1740 mm (68.5 in) (C) Overall height 2500 mm (98.4 in) (E) Overall height of cab 2500 mm (98.4 in) (F) Ground clearance of counterweight 540 mm (21.3 in) (H) Minimum ground clearance...
Page 236 8 - SPECIFICATIONS Working range SMIL18MEX0148FA (A) Maximum digging reach 5315 mm (209.3 in) (A’) Maximum digging reach on ground 5200 mm (204.7 in) (B) Maximum digging depth 3135 mm (123.4 in) (B’) Maximum digging depth (8ft level) 2670 mm (105.1 in) (C) Maximum vertical wall digging depth 2190 mm (86.2 in) (D) Maximum digging height...
Page 237: Weights
8 - SPECIFICATIONS Weights Machine 4010 kg (8840.5 lb) / Operating weight (cab version) (*) (***) 4105 kg (9050 lb) 3870 kg (8532 lb) / Operating weight (canopy version) (**) (***) 3965 kg (8741 lb) Components Upperstructure assembly 1975 kg (4354.1 lb) Main frame weld assembly 460 kg (1014.1 lb) Engine assembly...
Page 238 8 - SPECIFICATIONS...
Page 239: Accessories
9 - ACCESSORIES ACCESSORIES###_10_### Direct fit buckets The data are referred for working operation with the dozer blade up and 400 kg (882 lb) counterweight. For cab configuration: • 1.30 m (51.18 in) arm, minimum lift value: 370 kg (815.71 lb). •...
Page 240 9 - ACCESSORIES Ditch cleaning direct fit bucket The data shown below are referred to working operation with the dozer blade up and the 400 kg (882 lb) counter- weight. For cab configuration: • 1.30 m (51.18 in) arm, minimum lift value: 370 kg (815.7 lb). •...
Page 241: Klac Type Buckets
NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. The data shown below are referred to working operation with the dozer blade up and the 400 kg (882 lb) counter- weight.
Page 242: Standard Buckets With Mechanical Coupler
NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. The data shown below are referred to working operation with the dozer blade up and the 400 kg (882 lb) counter- weight.
Page 243 9 - ACCESSORIES Ditch cleaning direct fit bucket The data shown below are referred to working operation with the dozer blade up and the 400 kg (882 lb) counter- weight. For cab configuration: • 1.30 m (51.18 in) arm, minimum lift value: 370 kg (815.7 lb). •...
Page 244: Standard Buckets With Hydraulic Pin Grabber Coupler
NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. The data shown below are referred to working operation with the dozer blade up and the 400 kg (882 lb) counter- weight.
Page 245 9 - ACCESSORIES Ditch cleaning direct fit bucket The data shown below are referred to working operation with the dozer blade up and the 400 kg (882 lb) counter- weight. For cab configuration: • 1.30 m (51.18 in) arm, minimum lift value: 370 kg (815.7 lb). •...
Page 246: Auxiliary Hydraulic Circuits
9 - ACCESSORIES Auxiliary hydraulic circuits First auxiliary hydraulic circuits (1-way or 2-way) The machine can be provided with a first auxiliary hydraulic circuit. This type of circuit can be alternatively set as a single acting circuit (1-way) or as a double-acting hydraulic circuit (2-way). •...
Page 247 9 - ACCESSORIES Hydraulic connections The two stop valves are located on each side of the arm to allow proper and safe connection of the attachment hydraulic lines to the first auxiliary hydraulic circuit. SMIL17MEX2841FA Open (A1) / Close (A2) tool of the stop valve 19 mm wrench Hydraulic connection (B) G 3/8”...
Page 248 9 - ACCESSORIES Operating controls If the auxiliary pedal is equipped proceed as follow: • 1-way: press the front side of pedal to full stroke to operate a single-acting hydraulic attachment . • 2-way: press the front side and rear side of pedal to full stroke to operate a double-acting hydraulic attachment.
Page 249 9 - ACCESSORIES Second auxiliary hydraulic circuits (4-way) The machine can be provided with an additional second auxiliary hydraulic circuit. This type of circuit can operate the attachments featuring secondary hydraulic actuation for positioning, such as rotating grabs or tiltable buckets. Hydraulic connections The two feed lines are located on each side of the arm under first auxiliary hydraulic circuit to allow proper and safe connection of the attachment hydraulic lines to the second auxiliary hydraulic circuit.
Page 250 9 - ACCESSORIES Operating controls Use the proportional switch located on the left-hand control lever to operate the double-acting hydraulic attachment. Move left-hand side and right-hand side to confirm the rotation control directions: • slide the switch to the left-hand side to rotate counter- clockwise the attachment.
Page 251 9 - ACCESSORIES Operation with the hydraulic breaker The hydraulic breaker is a single-acting hydraulic attachment, and shall be connected to the first auxiliary (1-way) hydraulic circuit. Therefore, to operate with a hydraulic breaker the machine shall be equipped with the first auxiliary (1-way) hydraulic circuit.
Page 252 9 - ACCESSORIES 7. Press and hold the front side of the pedal (if equipped) to full stroke in order to operate the hydraulic breaker with the continuous selected flow, providing a con- stant blowing frequency. Release the pedal to stop the breaker operation.
Page 253 9 - ACCESSORIES Precautions while operating the hydraulic breaker Avoid hitting objects with breaker. The breaker is heav- ier than the bucket and lowers faster. This may cause damage to the breaker, attachment, and upper structure. Always lower the breaker slowly until the chisel point touches the object to be broken before starting breaker operation.
Page 254 9 - ACCESSORIES Do not operate the breaker to the side of the machine. The machine may become unstable and undercarriage components life may be reduced. SMIL16MEX0465AA Operate the excavator carefully to avoid hitting the boom with the hydraulic breaker. SMIL16MEX0466AA Do not operate the breaker while striking.
Page 255 NOTICE: all attachment shown on this manual are exclusive to the North American Market. To all other markets contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. Hydraulic breaker...
Page 256 9 - ACCESSORIES Operation with the hydraulic auger The hydraulic auger is a double-acting hydraulic attachment, and shall be connected to the first auxiliary (2-way) hydraulic circuit. Therefore, to operate with a hydraulic auger the machine shall be equipped with the first auxiliary (2-way) hydraulic circuit.
Page 257 9 - ACCESSORIES 7. Use a suitable belt with eyebolt (A) to secure the link rod on the top of the arm to avoid unappropriated mov- ing and tapping on the top of the arm. NOTE: applies to pendulum mount only. SMIL17MEX2805BA 8.
Page 258 9 - ACCESSORIES 9. If the auxiliary pedal is equipped, press the front and rear sides of the pedal in order to rotate the auger clockwise and counterclockwise. SMIL19MEX0775BA 10. If the proportional switch on the right-hand control lever is equipped, slide the left-hand the proportional switch to operate the hydraulic auger.
Page 259 9 - ACCESSORIES Precautions while operating the hydraulic auger Avoid hitting objects with auger. The auger is heavier than the bucket and lowers faster. This may cause damages to the auger, attachment, and upper structure. Always lower the auger slowly until the bit point touches the ground to be drilled before starting auger operation.
Page 260 9 - ACCESSORIES Do not operate the auger to the side of the machine. The machine may become unstable and undercarriage com- ponents life may be reduced. SMIL16MEX0465AA Operate the excavator carefully to avoid hitting the boom with the hydraulic auger. SMIL17MEX2811AA Do not operate the auger while striking.
Page 261 NOTICE: all attachment shown on this manual are exclusive to the North American Market. To all other markets contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. Drive unit (1)
Page 262 9 - ACCESSORIES Pin, bushing and insert kit (4) Unit weight 16 kg (36 lb) NOTE: for cradle mount bracket application. SMIL17MEX2838AA Bit (5) Unit weight Maximum diameter 92 kg (203 lb) 450 mm (18 in) SMIL17MEX2794AA Auger bit extension (6) Unit weight Maximum length 26 kg (57 lb)
Page 263 9 - ACCESSORIES The auger pendulum mount assembly consist of the following items: • Drive unit (1) • Pendulum mount (2) • Bit (5) • Auger bit extension (6): this component, not shown in figure, must be installed between drive unit (1) and the bit (5).
Page 264: Hydraulic Oil - Breaker/Auger
9 - ACCESSORIES Hydraulic oil - breaker/auger When using the hydraulic breaker, hydraulic fluid deteriorates more quickly than during ordinary digging. Check the hydraulic fluid level more frequently. In addition, when changing the filters, also check the condition of the hydraulic fluid.
Page 265: Quick Coupling System - Klac Type
9 - ACCESSORIES Quick coupling system - Klac type WARNING Crushing hazard! Never put your hands inside the quick coupler mechanism. Turn off the engine and wait for all move- ment to stop. Failure to comply could result in death or serious injury. W1542A WARNING Hazard to bystanders!
Page 266 9 - ACCESSORIES Attachment engagement WARNING Misuse hazard! Follow the operating instructions in this chap- ter. Any other practice that has not received the prior approval of the manufacturer is con- sidered to be strictly forbidden. Failure to comply could result in death or se- rious injury.
Page 267 9 - ACCESSORIES 3. Pull the wrench handle to extract the locking plate, until it latches in place. 4. Remove the release tool, and store it in a compartment of the machine. 5. Align the arm (3) so that is parallel to the bucket (4), then engage the pins (5) that secure the quick coupler to the bucket hooks.
Page 268 9 - ACCESSORIES 7. Check the coupling between the bucket and the quick coupler. ○ (A) there must be no play between the alignment profiles. Lock all machine controls, get off the ma- chine, go near to the quick coupling system and check the coupling status.
Page 269 9 - ACCESSORIES Attachment disengagement - Mechanical version WARNING Misuse hazard! Follow the operating instructions in this chap- ter. Any other practice that has not received the prior approval of the manufacturer is con- sidered to be strictly forbidden. Failure to comply could result in death or se- rious injury.
Page 270 9 - ACCESSORIES Securing the quick coupling system NOTICE: The quick coupling system must be secured unless using another attachment. Be sure to retract the mobile plate of the quick coupling system. WARNING Cutting hazard! This operation could be dangerous. Do not put your hands near the mobile plate.
Page 271 Advised models NOTICE: all attachment shown on this manual are exclusive to the North American Market. To all other markets contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CON- STRUCTION dealer, before purchasing an attachment.
Page 272: Quick Coupling System - Mechanical Pin-Grabber Type
9 - ACCESSORIES Quick coupling system - Mechanical pin-grabber type WARNING Crushing hazard! Never put your hands inside the quick coupler mechanism. Turn off the engine and wait for all move- ment to stop. Failure to comply could result in death or serious injury. W1542A WARNING Hazard to bystanders!
Page 273 9 - ACCESSORIES 3. Extend the bucket cylinder (curl in) until the rear pin of the attachment is firmly seated in the coupler. 4. Stop the engine and get out of the machine. SMIL17MEX2814AA 5. Insert the release bar (3) and rotate the locking hooks upwards slightly.
Page 274 9 - ACCESSORIES Attachment disengagement WARNING Misuse hazard! Follow the operating instructions in this chap- ter. Any other practice that has not received the prior approval of the manufacturer is con- sidered to be strictly forbidden. Failure to comply could result in death or se- rious injury.
Page 275 9 - ACCESSORIES 5. Install the locking pin (2) and the retainer pin (4). 6. Remove the release bar (3). 7. Get into the machine, fasten the seat belt and start the engine. SMIL17MEX2819AA 8. Retract the bucket cylinder. 9. Move the arm away from the attachment pin until the coupler hooks are clear of the attachment.
Page 276 Advised models NOTICE: all attachment shown on this manual are exclusive to the North American Market. To all other markets contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CON- STRUCTION dealer, before purchasing an attachment.
Page 277: Quick Coupling System - Hydraulic Pin-Grabber Type
9 - ACCESSORIES Quick coupling system - Hydraulic pin-grabber type WARNING Crushing hazard! Never put your hands inside the quick coupler mechanism. Turn off the engine and wait for all move- ment to stop. Failure to comply could result in death or serious injury. W1542A WARNING Hazard to bystanders!
Page 278 9 - ACCESSORIES Attachment engagement WARNING Misuse hazard! Follow the operating instructions in this chap- ter. Any other practice that has not received the prior approval of the manufacturer is con- sidered to be strictly forbidden. Failure to comply could result in death or se- rious injury.
Page 279 9 - ACCESSORIES 6. Continue to curl the coupler until the attachment is lifted off the ground. SMIL17MEX2824AA 7. Fully curl the bucket and hold the bucket curl lever for approximately 3 – 5 s to allow the jaw to fully engage and clamp the bucket pin.
Page 280 9 - ACCESSORIES 8. From the operator’s seat perform a visual inspection and check in order to verify the correct rear jaw en- gagement. If the front lock is not visible proceed as follows: • Fully extend the bucket cylinder. •...
Page 281 9 - ACCESSORIES NOTE: If is not possible to perform the visual inspection and check from the cab, the operator must get out of the cab and stand in a safe place to visually inspect before operating the machine. SMIL17MEX2827AA To ensure that the bucket pins are securely held by the coupler, apply pressure to the bucket by rotating it against the ground and away from the machine be-...
Page 282 9 - ACCESSORIES Attachment disengagement WARNING Misuse hazard! Follow the operating instructions in this chap- ter. Any other practice that has not received the prior approval of the manufacturer is con- sidered to be strictly forbidden. Failure to comply could result in death or se- rious injury.
Page 283 9 - ACCESSORIES 5. Once the jaw is fully retracted, lower the attachment to ground and slowly curl the coupler back to release the rear attachment pin. SMIL17MEX2830AA 6. Lift the dipper arm until the coupler has disengaged from the front attachment pin. The attachment is now safety disengaged.
Page 284 Advised models NOTICE: all attachment shown on this manual are exclusive to the North American Market. To all other markets contact your authorized NEW HOLLAND CONSTRUCTION dealer, before purchasing an attachment. NOTE: contact your authorized NEW HOLLAND CON- STRUCTION dealer, before purchasing an attachment.
Page 285: Load Handling
9 - ACCESSORIES Load handling WARNING Crushing hazard! During load handling operations, it is very important to adhere strictly to the instructions given in this manual and local legislation. Failure to comply could result in death or serious injury. W0257A WARNING Improper operation or service of this machine can result in an accident.
Page 286 9 - ACCESSORIES To handle suspended loads proceed as described below: • Evaluate (if not known) the mass of the object to be handled and compare it with the data listed in the liftable loads chart (1) located in the cab/canopy. Do not lift loads exceeding the maximum values prescribed by the table.
Page 287 9 - ACCESSORIES Load handling chart The load handling chart indicates the rated lift capacities that you must consider at different distances from the swing axis. The rated lift capacity is defined according to SAE J1097 and ISO 10567 as the smaller value of either the rated tipping load ( 75% of the tipping load) or the rated hydraulic lift capacity ( 87% of the hydraulic lift capacity).
Page 288 In the event abnormal conditions are found, contact the NEW HOLLAND CON- STRUCTION. dealer. NOTICE: the pressure setting of the safety valves must be checked every 6 months. Consult the NEW HOLLAND CONSTRUCTION dealer. 9-50...
Page 289: Thumb Bracket
Do not use the thumb bracket to handle loads. Failure to comply could result in death or se- rious injury. W1572A NOTE: consult your NEW HOLLAND CONSTRUCTION dealer to select the hydraulic thumb compatible with your SMIL16MEX1106AA machine and to install it correctly. 9-51...
Page 290: Rotating Beacon
Rotating beacon When you operate a machine on a road or beside a road, a rotating beacon is required to avoid any traffic accident. Please contact your NEW HOLLAND CONSTRUCTION dealer to install it. SMIL19MEX0711AA During the machine transfer, change the position of the lamp to the horizontal position.
Page 291: Fire Extinguisher
Two threaded holes are available to the rear-left upright of the upper frame to install the fire extinguisher (refer to the figures to locate the threaded holes). Please contact your NEW HOLLAND CONSTRUCTION dealer to obtain the fire extinguisher. Canopy version...
Page 292 9 - ACCESSORIES 9-54...
Page 293 Index ###_Index_### Air cleaner ......... 6-48, 6-55 Air-conditioning compressor drive belt .
Page 294 General specifications - Biodiesel fuels ....... Grease points (Blade) ........6-20, 6-29 Grease points (Boom and arm) .
Page 295 Radiator and coolers ........6-51 Radio .
Page 296 New Holland dealer. © 2021 CNH Industrial Italia S.p.A. All Rights Reserved. New Holland is a trademark registered in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates.

New Holland E37C Original Instructions Manual

1 General Information

2 Safety Information

3 Controls and Instruments

4 Operating Instructions

5 Transport Operations

6 Maintenance

Every 100 Hours

Every 250 Hours

Every 500 Hours

Every 1000 Hours

Every 2000 Hours

Every 5000 Hours

When Necessary

Fuse and Relay Locations

7 Troubleshooting

8 Specifications

9 Accessories

Quick Links

Troubleshooting

Related Manuals for New Holland E37C

Summary of Contents for New Holland E37C

Table of Contents