CaryMart 0020101 Manual

5000 Meters RF Wireless Receiver (Model 0020101 S2PUW-DC-ANT2)
Feature:
Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship,
offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks,
motors, fans, winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various devices.
The installation of wireless control is easy and fast.
Super long range, with a transmitter to form a complete set, the working distance can reach 5000m in an open ground.
Waterproof : The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Power Supply: Four working voltage versions, DC 6V, 9V, 12V, 24V.
Relay Output: This receiver is relay output, it can be used to operate both DC and AC equipments. The terminal is NO / NC (normally open / normally
closed), which serves as a switch. That means you should also connect a separate power supply to equipments.
High Power: Each channel can work at maximum current 30A, such as 360W/12V, 180W/6V, 270W/9V, 720W/24V, 3000W/110V, 6000W/220V.
With wired control terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.
External magnetic sucker antenna with 5meters cable, the antenna can be installed outside the building to get better working distance.
You can control the equipments by using the receiver with transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With characteristics of reverse power protection and over current protection.
Reliable control: The code has thousands of different combinations, and the receiver only works with the transmitter which use the same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Feedback Function:
The receiver and the transmitter have a Two-way working mode, and the user can know the working status of receiver by the transmitter in such a
long distance.
Two-way working mode: When you press the remote control to send RF signal to the receiver, if the receiver has been successfully triggered or
operated, the receiver will immediately transmit a RF feedback signal to the remote control. Then the remote control will send out a buzzing sound to
inform you that the receiver has been successfully operated.
Receiver Parameters:
Model No. S2PUW-DC06-ANT2 / S2PUW-DC09-ANT2 / S2PUW-DC12-ANT2 / S2PUW-DC24-ANT2
Power Supply (Operating Voltage): DC6V (S2PUW-DC06-ANT2), DC9V±1V (S2PUW-DC09-ANT2), DC12V±1V (S2PUW-DC12-ANT2), DC24V±2V
(S2PUW-DC24-ANT2)
Working Frequency: 433.92MHz
Channel: 2 CH
Control Modes: Toggle, Momentary, Latched
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Static Current: ≤6mA
Maximum Working Current of Relay: 30A
PCB size: 140mm x 73mm x 18mm
Case size: 192mm x 100mm x 45mm
External Magnetic Sucker Antenna:
Frequency Range: 300~450MHz
Impedance: 50Ω
Antenna Length: 15cm
Cable Length: 5m, we also can offer longer cable, such as 10 meters, 30 meters.
Anti-interference, waterproof, shielded wire set inside.
Magnetic stand design for easy to install.
Matching Transmitters:
Notice: This receiver only works with 5000m transmitters, such as model CC-2 / CC-4 (5000M), or CCW-2 / CCW-4 (5000M, waterproof).
When you set the receiver in toggle mode or momentary mode, it should work with two buttons transmitter, such as model CC-2 (5000m), or CCW-2
(5000m, waterproof). When you set the receiver in latched mode, it should work with four buttons transmitter, such as model CC-4 (5000m) or
CCW-4 (5000m, waterproof).
Working Range:
Super long range, with a transmitter (such as CC-2) to form a complete set, the maximum working distance can reach 5000M in an open ground. The
maximum working distance is an ideal range , it shall be operated with no barriers and interference in an open ground. But in the practice, it will be
hindered by trees, walls or other constructions, and will be interfered by other wireless sign. Therefore, the actual distance may not reach this
maximum working distance.
Usage (with the transmitter CC-2):
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.
Notice: The receiver is relay output, not DC/AC power output. Initial state of relay output terminals: Terminals B and C are Normally Open; Terminals
A and C are Normally Closed.
Wiring:
SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: sale@carymart.com