CaryMart S1PFC-AC220-ANT3 Manual

RF Wireless Receiver (Model 0020132 S1PFC-AC220-ANT3)
Features:
Application: It can be used in rolling blinds, rolling doors, projection screens, awnings, pumps, winches, conveyors or other appliances and
equipments with AC motors, it can remote control AC motor rotates in the positive or reversal direction.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
You can rotate a motor in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance.
The RF wireless signal can pass through walls, floors and doors.
High Power: Each channel can work at maximum current 30A.
With limit control terminals: You can connect limit switches or sensors to stop the motor.
With wired control terminals: You can connect manual switches or external devices (with low level output signal, such as sensors) to control the
motor.
With the external antenna, it can have a further working range.
Design with low-power and high-speed CMOS technology.
You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No: S1PFC-AC220-ANT3
Control Mode: Latched or Momentary
Coding Type: Fixed code or learning code
Coding Setting: By learning
Power Supply (Operating Voltage): AC100~240V (110V/120V/220V/240V)
Output: AC100~240V (110V/120V/220V/240V)
Working Frequency: 315MHz / 433MHz
Channel: 1 CH, can work with 1 AC motor
Static Current: ≤6mA
Maximum Working Current: 30A / each channel, so motor's maximum starting current can not exceed 30A.
PCB Size: 140mm x 73mm x 18mm
Case Size: 192mm x 100mm x 45mm
External telescopic antenna:
Length of external telescopic antenna: 108mm / 445mm (stretch)
External telescopic antenna use SMA connector.
If you stretches the external telescopic antenna, it can have a further working range, which is twice as much as it used to be.
Weight of external telescopic antenna: 16.5g
Matching Transmitters:
This receiver can work with different transmitters. When you set the receiver in momentary mode, it should work with two button transmitters, such as
model C-2-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2-2 (500M), or CB-2 (1000M) etc. When you set the receiver in latched mode, it
should work with three or four button transmitters, such as model C-3-2,(100M), CWB-3 (50M, waterproof), CB-3 (1000M),CP-4 (500M), or CV-4-2
(500M) etc.
Working Range:
With a transmitter (such as CV-4-2) to form a complete set, the working distance can reach 500M in an open ground. The maximum working distance
500M is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees,
walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may or may not reach 500M. If you want to
have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB
transmitters.
Usage (with transmitter CV-4-2):
Connect live wire to terminal "L" and neutral wire to terminal "N". Then connect AC motor to terminals "UP", "COM" and "DOWN". You can exchange
"UP" and "DOWN" wires of motor to change the rotating direction of motor.
Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)
Press button ▲: motor rotates in positive direction.
Press button ▼: motor rotates in reversal direction.
Press button ■ : motor stops.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: sale@carymart.com