Related Manuals for Inepro 132312
Summary of Contents for Inepro 132312
- Page 1 Konica Minolta Kit ~ Bizhub ~ 132312 Installation Manual | Konica Minolta Kit ~ Bizhub ~ 132312 Inepro Kit number: 132312 Konica Kit number: 9967000949 © 2019 Inepro B.V. All rights reserved...
-
Page 2: Table Of Contents
2 Attach the bracket to the copier ................................ 10 Set up the copier 1 Konica Minolta Bizhub Colour V5 ................................ 22 Set up the PayCon 1 Behaviour ................................ 26 2 Network ................................ 27 3 General Settings ................................ 28 Notes http://www.inepro.com Version 2.2.30 Inepro B.V. -
Page 3: Introduction
Introduction Part... - Page 4 2. Prepare and construct the hardware. To read more go to page 3. Set up the copier, read more on page 4. Set up the PayCon, you will find more information on page Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 5: Check Kit Content
Check Kit Content Part... - Page 6 PayCon copier mounting bracket · KM cableset Minolta Serial I/F - V3 · KM screwset Bizhub V3 C550 · KM Mounting plate Bizhub Colour - V5 · This manual · 150cm Black cat 5 network cable Konica Minolta Kit ~ Bizhub ~ 132312...
- Page 7 KM Screwset Bizhub Colour V3 KM Screw set Bizhub Colour V3 In the "KM Screwset Bizhub Colour V3" you should find: · 3x M4 x 5mm Dome shaped, cross head screws · 1x M4 x 12mm Dome shaped, cross head screw ·...
- Page 8 KM Cableset Minolta serial I/F V3 In the "KM Cableset Minolta serial I/F V3" you should find: · Rip ties · Ferrite core · Connection cable · Double sided adhesive tape 25mm x 30mm · Connector block male/male Konica Minolta Kit ~ Bizhub ~ 132312...
- Page 9 PayCon copier mounting bracket PayCon copier m ounting bracket In the "PayCon copier mounting bracket" you should find: · PayCon copier mounting bracket · Dome shaped, cross head screws · Dome shaped, cross head screws (not needed for this installation) Additional requirements for installation ·...
-
Page 10: Hardware Setup
Hardware Setup Part... - Page 11 Hardware Setup Additional requirements: · Pair of wire cutters · No. 2 cross head screwdriver · No. 1 PosiDriv head screwdriver · PayCon Copy · 2x CAT-5 Network cables (one cable included) Attach the PayCon to the PayCon bracket Break out the appropriate gaps in the flaps 2.
- Page 12 The mounting instructions differ for the different type of copiers its supports. The instructions for each part will start with the list of copiers that the instructions are meant for. - Bizhub C203 - Bizhub C253 - Bizhub C353 Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 13: Attach The Bracket To The Copier
Attach the bracket to the copier 1. Screw off the copier flap and open the scanner top to lift the flap out, and rem ove the backside flap as w ell. 2. Attach the cable w ith the 2 rip ties to the existing cable , as show n above. Make sure you do not allow the cable to be too long because then it w ill hinder the door. - Page 14 6. Connect the copy cable and close the back and side flap. Guide the cables in the slit w rap harnas and attach it to the cable guide w ith the rip ties. Connect the netw ork cable to the socket hidden behind the corner flap Rem ove the transport foils to finish the installation Konica Minolta Kit ~ Bizhub ~ 132312...
- Page 15 Attach the bracket to the copier 8. Finished...
- Page 16 3. Attach the PayCon. Shorten the cable to approxim ately 55 centim eters (21 segm ents should be cut off). Feed the cable through the slit w rap harness. Feed the cable inside the copier. Attach the slit w rap harness to the cable guides w ith the rip ties. Konica Minolta Kit ~ Bizhub ~ 132312...
- Page 17 Attach the bracket to the copier Photo for Bizhub C451, C550, C650 Photo for Bizhub C452, C552, C652 4. Place the ferrite core w ith the adhesive tape. Loop the cable in the ferrite core and run it through the original cable guiders. Connect the cable to the connector inside the copier.
- Page 18 M3 12m m screw s M3 16m m screw M3 20m m screw M3 x 5m m spacers M3 x 12m m spacer Black rip ties 2. from the cableset White rip ties Konica Minolta Kit ~ Bizhub ~ 132312...
- Page 19 Attach the bracket to the copier - Bizhub C220 - Bizhub C280 - Bizhub C360 Unscrew the w hite rim (3 screw s) and the plastic cover (6 screw s). Rem ove protection cap Open left protection cap and rem ove the 2 upper left screw s...
- Page 20 Break open the break-out hole in the cover. Put the copy cable through the hole, connect the netw ork cable behind the door and put the rest of the cables in the cable hose. Konica Minolta Kit ~ Bizhub ~ 132312...
- Page 21 Attach the bracket to the copier The cable should enter here. Place the ferrite core on the plastic and loop the cable trough. Connect the cable to m ale connector. Overview copy cable.
- Page 22 M3 x 20m m Dom e shaped, cross head screw s M3 x 12m m Dom e shaped, cross head screw s M3 x 15m m spacer M4 x 12m m spacer M3 Black nylon cable guiders Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 23: Set Up The Copier
Set up the copier Part... - Page 24 Konica Minolta Bizhub C452 · Konica Minolta Bizhub C552 · Konica Minolta Bizhub C652 · Konica Minolta Bizhub C650 The PayCon Interface setting should be 'KoMi Serial'. (See chapter: 'Set up the PayCon' on page Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 25: Konica Minolta Bizhub Colour V5
Konica Minolta Bizhub Colour V5 Activating the payment system: Press <Utility/Counter> Press <Meter Count> Press <Check Details> Press <stop> <0> <0> <stop> <0> <1> SERVICE MODE Press <stop> <9> Select <Management Function Choice> Select <Vendor 2> Select <Message> Select <Type1> (for coins only) or Select <Type2>... - Page 26 Note: When "Print Function Setting" is set to "ON", all printjobs need a job log code. Printjobs without this code will be automatically deleted at the MFP. Note: when using central server software for controlling printjobs (like DocuPro or Pcounter) "Print Function Setting" should be set to "OFF" (otherwise you have to pay twice). Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 27: Set Up The Paycon
Set up the PayCon Part... - Page 28 Payment Option', continue with step 2. b. On the server (SVS), go to step 3. c. On the PayCon terminal, you will need ECOS 'KM - I - Local Accounts', go to step 4. Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 29: Behaviour
Select 'Disabled', press and go to step 2f. , Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => 'Inepro SLE'. e. Select 'Disabled' and press f. Do you use Pcounter? if you do, continue with step 3, if you don't, go to step 8. - Page 30 , Go to 'Main Menu' => 'Copier' => 'Interface' b. Select the Interface setting for your machine and press . The correct settings can be found in the chapter: 'Set up the copier', on page Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 31: General Settings
General Settings 9. Products. The copy/print/scan products in the PayCon have a fixed order and number. They are used to connect the paper signals form the copier to prices in the PayCon. These products and their names can also be set with PCounter. , Go to 'Main Menu' =>... - Page 32 , Go to 'Main Menu' => 'Terminal' => 'Default Language'. b. Select a language from the list and confirm with c. Go to 'Main Menu' => 'Terminal' => '<Nth> Language' to add extra languages in the same way. Konica Minolta Kit ~ Bizhub ~ 132312...
-
Page 33: Notes
Notes Part... - Page 34 Notes Notes This area is meant for the reader's notes: Konica Minolta Kit ~ Bizhub ~ 132312...