Related Manuals for Inepro 132360
Summary of Contents for Inepro 132360
- Page 1 Konica Minolta Kit - Bizhub 132360 Installation Manual | Konica Minolta Kit - Bizhub 132360 Inepro Kit number: 132360 Konica Kit number: 9967000514 © 2019 Inepro B.V. All rights reserved...
-
Page 2: Table Of Contents
2 Attach the bracket to the copier ................................ 10 Set up the copier 1 Konica Minolta Bizhub 420 Series ................................ 17 Set up the PayCon 1 Behaviour ................................ 20 2 Network ................................ 21 3 General Settings ................................ 22 Notes http://www.inepro.com Version 2.2.20 Inepro B.V. -
Page 3: Introduction
Introduction Part... - Page 4 2. Prepare and construct the hardware. To read more go to page 3. Set up the copier, read more on page 4. Set up the PayCon, you will find more information on page Konica Minolta Kit - Bizhub 132360...
-
Page 5: Check Kit Content
Check Kit Content Part... - Page 6 · PayCon copier mounting bracket · KM screwset Bizhub 420 / 500 · KM Mounting plate Bizhub 420 / 500 · 65cm x 15mm Black slit wrap harness (the black hose) · This manual Konica Minolta Kit - Bizhub 132360...
- Page 7 KM Screwset Bizhub 420 / 500 KM Screw set Bizhub 420 / 500 In the "KM Screwset Bizhub 420 / 500" you should find: · M3 Black nylon cable guiders · M4 x 5mm Dome shaped, cross head screws · M3 x 12mm Dome shaped, cross head screws ·...
- Page 8 Ferrite core · 25 x 30mm Double-sided adhesive tape · Connection cable KM Mounting plate Bizhub 420 / 500 KM Mounting plate Bizhub 420 / 500 1x KM mounting plate Bizhub 420 / 500 Konica Minolta Kit - Bizhub 132360...
- Page 9 PayCon copier mounting bracket PayCon copier m ounting bracket In the "PayCon copier mounting bracket" you should find: · PayCon copier mounting bracket · Dome shaped, cross head screws · Dome shaped, cross head screws (not needed for this installation) Additional requirements for installation ·...
-
Page 10: Hardware Setup
Hardware Setup Part... - Page 11 Hardware Setup Additional requirements: · Pair of wire cutters · No. 2 cross head screwdriver · No. 1 PosiDriv head screwdriver · PayCon Copy · 2x CAT-5 Network cables (one cable included) Recommend Tools: · SHR Slit Wrap Tool, Richco part nr. CAT-15-PP (for guiding cables into the slit harness wrap) Attach the PayCon to the PayCon bracket Break out the appropriate gaps in the flaps 2.
- Page 12 5. Mount the PayCon bracket on the m ounting plate w ith the M4 x 5m m dom e shaped cross head screw s. Place the ferrite cores and loop the netw ork cables through them once Attach the PayCon bracket to the copier Konica Minolta Kit - Bizhub 132360...
-
Page 13: Attach The Bracket To The Copier
Attach the bracket to the copier 1. Rem ove both the plastic and the m etal backplate of the copier so the controller board w ill be revealed Rem ove the original screw s 3. Place the m ounting plate w ith the PayCon and cable guider on the copier... - Page 14 5. Feed the cables through the slit w rap harness and create an exit hole about half-w ay in the slit w rap harness, so the interface cable can be fed through the copier to the controller board Konica Minolta Kit - Bizhub 132360...
- Page 15 Attach the bracket to the copier 6. Fasten the harness on the guiders, fasten it w ith the rip ties Place the ferrite core...
- Page 16 Hardware Setup 8. Connect the interface cable connector and loop the w ire through the ferrite core 9. Fasten both the m etal and the plastic backplate of the copier Konica Minolta Kit - Bizhub 132360...
- Page 17 Attach the bracket to the copier 10. Finished...
-
Page 18: Set Up The Copier
Set up the copier Part... -
Page 19: Konica Minolta Bizhub 420 Series
Set up the copier Turn on the copier. In this chapter you will set up the copier for use with the PayCon system. Examine the exact settings below. Konica Minolta Bizhub Series · Konica Minolta Bizhub 360 · Konica Minolta Bizhub 420 ·... - Page 20 Note: When "Print Function Setting" is set to "ON", all printjobs need a job log code. Printjobs without this code will be automatically deleted at the MFP. Note: when using central server software for controlling printjobs "Print Function Setting" should be set to "OFF" (otherwise you have to pay twice). Konica Minolta Kit - Bizhub 132360...
-
Page 21: Set Up The Paycon
Set up the PayCon Part... - Page 22 Payment Option', continue with step 2. b. On the server (SVS), go to step 3. c. On the PayCon terminal, you will need ECOS 'KM - I - Local Accounts', go to step 4. Konica Minolta Kit - Bizhub 132360...
-
Page 23: Behaviour
Select 'Disabled', press and go to step 2f. , Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => 'Inepro SLE'. e. Select 'Disabled' and press f. Do you use Pcounter? if you do, continue with step 3, if you don't, go to step 8. - Page 24 , Go to 'Main Menu' => 'Copier' => 'Interface' b. Select the Interface setting for your machine and press . The correct settings can be found in the chapter: 'Set up the copier', on page Konica Minolta Kit - Bizhub 132360...
-
Page 25: General Settings
General Settings 9. Products. The copy/print/scan products in the PayCon have a fixed order and number. They are used to connect the paper signals form the copier to prices in the PayCon. These products and their names can also be set with PCounter. , Go to 'Main Menu' =>... - Page 26 , Go to 'Main Menu' => 'Terminal' => 'Default Language'. b. Select a language from the list and confirm with c. Go to 'Main Menu' => 'Terminal' => '<Nth> Language' to add extra languages in the same way. Konica Minolta Kit - Bizhub 132360...
-
Page 27: Notes
Notes Part... - Page 28 Notes Notes This area is meant for the reader's notes: Konica Minolta Kit - Bizhub 132360...