Set up the copier 1 Konica Minolta Bizhub C350 ................................ 15 2 Other Konica Minolta Bizhub Colour copiers ................................ 16 Set up the PayCon 1 Behaviour ................................ 19 2 Network ................................ 20 3 General Settings ................................ 21 Notes http://www.inepro.com Version 2.2.30 Inepro B.V.
Page 4
2. Prepare and construct the hardware. To read more go to page 3. Set up the copier, read more on page 4. Set up the PayCon, you will find more information on page Konica Minolta Kit - Bizhub 132300...
Page 6
In the "KM Mounting kit for Bizhub colour" you should find: · PayCon copier mounting bracket · KM cableset Minolta serial I/F · KM screwset Bizhub colour · KM Mounting plate Bizhub colour · This manual Konica Minolta Kit - Bizhub 132300...
Page 7
KM Screwset Bizhub colour KM Screw set Bizhub colour In the "KM Screwset Bizhub colour" you should find: · Cable guiders · M4 x 5mm Dome shaped, cross head screws · M4 x 20mm Dome shaped, cross head screws · M4 Star lock washers KM Mounting plate Bizhub colour KM Mounting plate Bizhub colour...
Page 8
KM Cableset Minolta serial I/F KM Cableset Minolta serial I/F In the "KM Cableset Minolta serial I/F" you should find: · Rip tie · Ferrite core · Connection cable · Double sided adhesive tape 25mm x 30mm Konica Minolta Kit - Bizhub 132300...
Page 9
PayCon copier mounting bracket PayCon copier m ounting bracket In the "PayCon copier mounting bracket" you should find: · PayCon copier mounting bracket · Dome shaped, cross head screws · Dome shaped, cross head screws (not needed for this installation) Additional requirements for installation ·...
Page 11
Hardware Setup Additional requirements: · Pair of wire cutters · No. 2 cross head screwdriver · No. 1 PosiDriv head screwdriver · PayCon Copy · 2x CAT-5 Network cables (one cable included) Attach the PayCon to the PayCon bracket Please follow these steps: Break out the appropriate gaps in the flaps 2.
Page 12
Close and gently screw dow n the final flap Place the PayCon bracket on the PayCon w ith the screw s from the bracket kit, (you don't need the three sm aller screw s). Konica Minolta Kit - Bizhub 132300...
Attach the PayCon to the bracket 6. Align the holes of the m ounting plate w ith the PayCon bracket and fasten it w ith the 3 M4 x 5m m screw s and their star lock w ashers Gently open the ferrite core and loop the connection and netw ork cables through once and loop the pow er supply cable through twice.
Page 14
Guide the w ires on the copier w ith the 20 w ire guiders and connect the interface cable to the connector of the Konica Minolta VK-501 vendor kit (not included) Rem ove the transport foils to finish the installation Konica Minolta Kit - Bizhub 132300...
Set up the copier Turn on the copier. In this chapter you will set up the copier for use with the PayCon system. Examine the exact settings below. Konica Minolta Bizhub C350 · Konica Minolta Bizhub C350 The PayCon Interface setting should be 'Minolta Serial'. (See chapter: 'Set up the PayCon' on page Activating the payment system: 1.
Set up the PayCon Turn on the PayCon. Refer to the technical PayCon Copy manual for handling the PayCon menu and changing settings. The settings in the PayCon can be find in the tree-top menu structure of the PayCon. To simplify thing, we will use a graphic representation of this menu to show you where the setting can be found.
Page 22
Select 'Disabled', press and go to step 2f. , Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => 'Inepro SLE'. e. Select 'Disabled' and press f. Do you use Pcounter? if you do, continue with step 3, if you don't, go to step 8.
Network 6. Fixed IP addresses: a. Set 'IP-address' to an IP-address in your network range and confirm with b. Set the subnet mask ('netmask') to '255.255.255.0' or to the subnet mask needed in your network and confirm with c. Set the 'default gateway' to the IP-address of the default gateway in your network and confirm with 7.
Page 24
12. Maximum Balance, the Maximum Balance allowed on a card or account. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Maximum Balance'. b. Type in the maximum balance and confirm with Konica Minolta Kit - Bizhub 132300...
General Settings 13. Project ID, the unique number for all PayCon's on this project or site. , Go to 'Main Menu' => 'Terminal' => 'Project ID' b. Press , type the Project ID and confirm with 14. Date and Time, the time and date that are used for the timestamp on the transactions. Remember if the timezone is changed the time will change accordingly.