Download Print this page

Dell 2200 Replacement Manual

Microprocessor replacement
Hide thumbs Also See for 2200:

Advertisement

®
Dell
PowerEdge
Microprocessor Replacement
T
his document provides the procedures for replacing the Intel
microprocessor(s) in a Dell PowerEdge 2200 system.
P
recautionary Measures
Before you perform any of the procedures in this document, take a few
moments to read the following warning for your personal safety and to prevent
damage to the computer system from ESD.
WARNING FOR YOUR PERSONAL SAFETY AND PROTECTION
OF THE EQUIPMENT: Only trained service technicians should per-
form the following procedures. Before you start to work on the
computer, perform the following steps in the sequence listed.
1. Turn off the computer and any attached peripherals.
2. Disconnect the computer and any attached peripherals from their
power sources to reduce the potential for personal injury.
3. Disconnect any communications cables.
4. Wear a wrist grounding strap, and clip it to any unpainted metal sur-
face on the computer chassis.
If a wrist grounding strap is not available, touch any unpainted
metal surface on the back of the computer chassis to discharge any
static charge from your body.
WARNING: The power supply in this computer system produces high
voltages and energy hazards, which can cause bodily harm. Only trained
service technicians are authorized to remove the computer cover and
access any of the components inside the computer.
®
2200 Systems
Dell PowerEdge 2200 Systems Microprocessor Replacement
®
Pentium
®
II
1

Advertisement

loading

Summary of Contents for Dell 2200

  • Page 1 PowerEdge Microprocessor Replacement his document provides the procedures for replacing the Intel microprocessor(s) in a Dell PowerEdge 2200 system. recautionary Measures Before you perform any of the procedures in this document, take a few moments to read the following warning for your personal safety and to prevent damage to the computer system from ESD.
  • Page 2: R Eplacing A Microprocessor

    300- and 333-MHz microprocessors. An updated version of the EISA Configuration Utility Diskette has been included in the replacement kit; use it instead of the EISA Configuration Utility on the Dell Server Assistant CD. Follow these steps to save the settings: a.
  • Page 3 4. If you are adding a secondary microprocessor, remove the terminator card from the second microprocessor connector (see Figure 2). NOTE: If you are not adding a secondary microprocessor, do not remove the terminator card. Go to step 5. Dell PowerEdge 2200 Systems Microprocessor Replacement...
  • Page 4 5. If you are upgrading an existing microprocessor, remove the micro- Dell PowerEdge 2200 Systems Microprocessor Replacement terminator card microprocessor retention bracket Figure 2. Removing a Terminator Card a. Remove the terminator-card retention bracket cover that holds the termi- nator card in place. Using the thumb and forefinger of each hand, pinch the vertical tabs at each end of the cover, and then lift the cover straight b.
  • Page 5 Lift the microprocessor module straight up and out of the micro- processor retention bracket on the system board. primary microprocessor- module retention screws (2) secondary microprocessor- module retention screws (2) system board assembly microprocessor-module retention latches (2) Dell PowerEdge 2200 Systems Microprocessor Replacement...
  • Page 6 7. Reinstall the two screws securing the microprocessor-module heat sink 8. Change the microprocessor speed jumper setting to correspond to the Dell PowerEdge 2200 Systems Microprocessor Replacement a. Make sure the new microprocessor-module retention latches are in a protracted position so that the retention latches will snap into position when the microprocessor module is installed.
  • Page 7 13. Run the system diagnostics to verify that the new microprocessor is operating correctly. See Chapter 2, “Using the Dell Server Assistant CD,” in the Dell Power- Edge 2200 Systems User’s Guide for information on running the diagnostics from the Dell Server Assistant CD. The Diagnostics and Troubleshooting Guide provides additional information on running the Dell Diagnostics and troubleshooting any problems that may occur.
  • Page 8: System Board Jumpers

    To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s) indicated (see Figure 6). See Table 1 for jumper descriptions. Figure 6. System Board Jumpers Dell PowerEdge 2200 Systems Microprocessor Replacement ystem Board Jumpers primary...
  • Page 9 333 MHz. Jumper installed only if microprocessor’s internal speed is 300 MHz. Jumper installed only if microprocessor’s internal speed is 266 MHz. Jumper installed only if microprocessor’s internal speed is 233 MHz. Dell PowerEdge 2200 Systems Microprocessor Replacement...