Subscribe to Our Youtube Channel
Related Manuals for Lyngdorf MP-40
Summary of Contents for Lyngdorf MP-40
- Page 1 MODEL MP-40 SURROUND SOUND PROCESSOR LYNGDORF MP-40 EXTERNAL CONTROL EXTERNAL CONTROL MANUAL MANUAL 2020...
-
Page 2: Table Of Contents
Controlling Voicings ....................18 Controlling Lipsync ....................18 Getting Zone 2 Audio Status ..................19 Controlling Feedback Level ..................19 Controlling OSD and OSD Menu ................20 IR CODES ......................... 22 RS232 pinout diagram ....................23 Lyngdorf MP-40 – External Control Manual... -
Page 3: Introduction
For control from a PC, use Telnet, Putty, or similar programs to open the TCP connection. If you do not know the IP address of the MP-40 on your local network, the MP-40 supports Apple´s Bonjour Discovery service, which must be on the computer you want to set up the MP-40 with. -
Page 4: Control Via Serial Port
Control Via Serial Port The serial port on the MP-40 is wired as a DTE, so for communication with a PC or similar, you will need a null modem adapter and gender changer. The port settings should always be 8 data bits, no parity, one stop bit and no hardware handshake. -
Page 5: Control Protocol
Feedback level 2: Each command is also echoed back with the ‘#’ in front of the command instead of ‘!’ character. For example, command “!VOL?<CR>” would return “#VOL?<CR>!VOL(XXX)<CR>”. Lyngdorf MP-40 – External Control Manual... -
Page 6: Commands
X = 1 !DTSDIALOGDN DTS Dialog Control Down !DTSDIALOGUP DTS Dialog Control Up !ENTER Enter button !EXIT Exit button !INFO Info button !INTERFACE? !INTERFACE(IP) Returns the active interface for this section, !INTERFACE(IP) or !INTERFACE(SERIAL) Lyngdorf MP-40 – External Control Manual... - Page 7 X is current Request RoomPerfect position RoomPerfect position (0=bypass, 1- 4=focus1 – focus4, 9=global) !RPFOC(X) X is RoomPerfect Set RoomPerfect position position to select (0=bypass, 1- 4=focus1 – focus4, 9=global) !RPFOC+ Next Roomperfect position button Lyngdorf MP-40 – External Control Manual...
- Page 8 SRC button on the P200 remote !SRCOFF- Decrease Source volume offset !SRCOFF? !SRCOFF(X) X is the source Request source volume offset for current volume offset for source the currently selected source. Between -100 (=- 10dB) and 100 (=+10dB) Lyngdorf MP-40 – External Control Manual...
- Page 9 Return LFE channel level trim (10 = 1dB) (-10dB) and 100 (+10dB) !TRIMLFE(X) X is between -100 Sets LFE channel level trim (10 = 1dB) (-10dB) and 100 (+10dB) !TRIMLFE+ Increases LFE channel level trim (10 = 1dB) Lyngdorf MP-40 – External Control Manual...
- Page 10 X is the source to Set zone B source select. For a list of sources use ZSRCS? !ZSRC(X)? !ZSRC(X)”Name” X is the number of Request info about zone B source x the requested source and “Name” Lyngdorf MP-40 – External Control Manual...
- Page 11 -999 to 240 (= - Set zone B volume 99.9 to +24.0 dB) !ZVOL+ Increase zone B volume !ZVOL+(X) -999 to 240 (= - Increase zone B volume by x 99.9 to +24.0 dB) Lyngdorf MP-40 – External Control Manual...
-
Page 12: Control Protocol Usage
Commands !ZVOL+<CR>, !ZVOL-<CR>, !ZVOL+(X)<CR>, !ZVOL-(X)<CR>, !ZVOL(X)<CR>, !ZVOL?<CR>, !ZMUTEON<CR>, !ZMUTEOFF<CR> and !ZMUTE<CR> are used to control zone 2 volume the same way as the main zone volume. Lyngdorf MP-40 – External Control Manual... - Page 13 It is never possible to set the volume above the maximum volume level setting with control interface commands, but it is very easy to accidentally reach the maximum volume level. Lyngdorf MP-40 – External Control Manual...
-
Page 14: Controlling Sources
0 and the index of the last source. This response is also sent automatically, when the source changes, if feedback level is 1 or higher. If main zone is off, the MP-40 will reply with the previous selected source. Zone 2: Sources on zone 2 are a subset of the sources set up for main zone. - Page 15 This response is also sent automatically, when the zone 2 source changes, if feedback level is 1 or higher. If zone 2 is turned off, the MP-40 will reply with the previous selected source. Commands !ZSRC+<CR> and !ZSRC-<CR> are used to select next or previous source.
- Page 16 Controlling Processing Modes The MP-40 processor has controls for selecting processing modes, also called audio modes. Command !AUDMODEL?<CR> can be used to get a list of processing modes; how many are there and what they are named. For example, a response for command !AUDMODEL?<CR>...
-
Page 17: Controlling Focus Positions
!RPFOCS?<CR>. The installer might add or remove focus positions at any time, so it is recommended to update the list of selectable focus positions at least in every boot-up. Lyngdorf MP-40 – External Control Manual... -
Page 18: Controlling Voicings
Commands !LIPSYNC+<CR> and !LIPSYNC-<CR> are used to adjust the lipsync trim value by 5ms or -5ms, respectively. Command !LIPSYNC(X)<CR> is used to set the lipsync trim directly. The valid value range for this command needs to be fetched from the MP-40 (see below). -
Page 19: Getting Zone 2 Audio Status
1 or higher. Controlling Feedback Level It is possible to set the feedback level from the external control interface with command !VERB(X)<CR>, where X is the wanted feedback level 0, 1 or 2. Lyngdorf MP-40 – External Control Manual... -
Page 20: Controlling Osd And Osd Menu
On Screen Menu when using a dedicated control interface. Direct controlling of HDMI outputs It is possible to control the HDMI outputs of the MP-40 controller directly using special control interface commands. The controlling allows routing of any HDMI input directly to either one of the HDMI outputs in bypass mode. - Page 21 Spdif 4 (Opt.) Spdif 5 (AES) Spdif 6 (Coax) Spdif 7 (Coax) Spdif 8 (Coax) Internal Player Audio Return Channel STREAM TYPES No. Stream type None vTuner Spotify AirPlay UPnP Storage Roon ready Unknown Lyngdorf MP-40 – External Control Manual...
-
Page 22: Ir Codes
0x37CA, 0x718E Input 2 0x37CA, 0x728D Input 3 0x37CA, 0x738C Input 4 0x37CA, 0x748B Input 5 0x37CA, 0x758A Input 6 0x37CA, 0x7689 Input 7 0x37CA, 0x7788 Input 8 0x37CA, 0x7887 Input 9 0x37CA, 0x7986 Lyngdorf MP-40 – External Control Manual... -
Page 23: Rs232 Pinout Diagram
RS232 pinout diagram Lyngdorf MP-40 – External Control Manual... - Page 24 Lyngdorf MP-40 – External Control Manual SL AUDIO A/S • ULVEVEJ 28 • 7800 SKIVE • DENMARK • WWW.LYNGDORF.COM...
Need help?
Do you have a question about the MP-40 and is the answer not in the manual?
Questions and answers