Detailed Descriptions Of Installer Menu Items - LG 65EV960H Commercial Mode Setup Manual

Installer Menu (Cont.)

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE
Specifies entry sequence to the Installer Menu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Energy saving feature. Determines the number of hours, in the
range 1 to 7, of inactivity allowed, either at the TV control panel
or from the remote, before the TV automatically turns itself OFF. If
set to 0, Power Management is disabled.
002 - AC ON (AC Power Switchable)
Set to 2 or 3 to enable the Instant ON feature (see additional
information below). Set to 0 (default) for standard TV turn ON/OFF
operation.
The Instant ON feature allows the TV to turn ON when AC power
is applied, but with video and audio muted (Muted ON). The TV
retains its ON status while appearing to be OFF. Pressing the
POWER button toggles off/on the video and audio mutes, so that
the TV appears to turn ON instantly.
•
If this item is set to 2, the TV will reboot and, if applicable (i.e.,
item 119 DATA CHANNEL set from 1 to 135 or 253), check
for and download any available updates from the Pro:Centric
server at every turn OFF. This setting is not recommended if the
TV will be configured with a resident application.
•
If this item is set to 3, the TV will not reboot to check for and
download updates at turn OFF, with the following exception:
the first time the TV is turned OFF after this item is set to 3,
the TV will reboot and initiate an update event (Data Channel
Auto Search and/or check for and download of updates—see
also paragraph below). This setting is recommended if the TV
will be configured with a resident application. In this mode, the
standard check for and download of updates is under application
control. Refer to your site-specific documentation for further
information on configuring the TV with a resident application.
When this item is set to 2 or 3, the TV also will reboot and initiate
an update event once every 24 hours. During the update event,
the TV, as applicable, performs a Data Channel Auto Search (item
119 set to 255) and/or checks for and downloads any available
updates from the Pro:Centric server (item 119 set from 1 to 135 or
253). The time at which this event occurs depends on the setting
of item 121 UPDATE TIME HR. See item 119 and 121 descriptions
for further information. Once the update cycle is complete, the TV
completes the reboot and resumes its Muted ON state.
Note: Instant ON is not supported when the TV is in MPI-EXT
Mode.
003 - BAND/AFC (Tuning Band)
Selects the RF band used by the NTSC tuner:
34
0 = Broadcast 1 = Cable (default)
2 = HRC 3 = IRC
Determine the RF band used by the RF distribution system, and
then select the appropriate value for this item before tuning
channels or running Auto Tuning (Channel Search). See also item
102 ATSC BAND.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial Major
Start Channel number when the TV is turned ON. This feature is
useful for an in-house information channel, since the TV would
always select that channel when it is turned ON. If set to 255,
the last channel tuned before the TV was turned OFF will be the
channel tuned when the TV is turned ON again.
0 = Aux
1 – 125 = Major Ch. #
126 = Map to Major CH 3
For a digital (ATSC) Start Channel, always remember to set item
104 to the Minor Start Channel number. If setting this item to 0
(Aux), make sure to also set item 046 STRT AUX SRCE to the
appropriate value.
Note: 126 and 127 are mapped only in SONIFI PPV Mode.
Note: The IP Start Channel shown above can only be set in the
Cloud Configuration Tool, which is typically used to configure TV
CPUs for FTG Mode. The same applies for the additional Major
Channel number range of 128 – 135 in Physical tuning and
128 – 999 in Virtual tuning mode. When the TV is in FTG Mode,
the appropriate values will be visible in the (read-only) Installer
Menu. For an IP Start Channel, item 004 will show value 253, the
IP address, and the port number. For an RF Start Channel, item
004 will show the channel's Major and Minor numbers.
Note: If the TV is being configured for Application Tuning Mode
operation with Pro:Centric Direct, the Start Channel is set in the
Pro:Centric Direct Admin Client, and Installer Menu item 004 is
automatically updated accordingly. When the TV is in Application
Tuning Mode, the appropriate values will be visible in the (read-only)
Installer Menu. For an IP Start Channel, item 004 will show value
253, the IP address, and the port number. For an RF Start Channel,
item 004 will show the channel's Major and Minor numbers.
005 - CHAN LOCK (Channel Lock)
Channel Lock is ideal if the system must always be on the same
channel. If set to 1, Channel Lock is enabled and it is not possible
to change channels with Channel Up/Down or number keys. If set
to 0 (default), Channel Lock is disabled.
Generally, this feature is used in connection with item 004 STRT
CHANNEL where the Start Channel may, for example, be set to
3 or 4. If the Start Channel is 3, then the TV will remain locked on
channel 3.
127 = Map to Major CH 4
253 = IP Start Channel
255 = Last Channel
206-4322