Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Regner RA-MINI PLAST Series
Summary of Contents for Regner RA-MINI PLAST Series
- Page 1 RA-MINI PLAST IN-LINE ACTUATOR SERIES User Manual www.regner.es...
- Page 2 Specifications are subject to change without notice. It is the responsibility of the user to determine the suitability of REGNER® products for a specific application. No part of this publication may be reproduced without written permission from Regner Engineering SLU.
-
Page 3: Table Of Contents
RA-MINI PLAST IN-LINE ACTUATOR SERIES 00. Contents 01. Preface ..............4 02. Safety ..............4 03. Declaration of Conformity ........5 04. Warranty ............... 6 05. Specifications ............6 06. Installation ............9 07. Maintenance ............10 08. Troubleshooting............ 11 09. -
Page 4: Preface
• Only properly qualified personnel can perform me- chanical and electrical installation of the actuator. • Do not mount, dismount or perform maintenance Thank you for choosing a REGNER® electric linear work while the actuator is in operation. actuator. REGNER® actuators are high-tech products, •... -
Page 5: Declaration Of Conformity
RA-MINI PLAST IN-LINE ACTUATOR SERIES 03. Declaration of 02.02. Symbols Used Conformity Important safety information is described under the following two symbols: REGNER ENGINEERING, S.L.U. Ripollès, 4.17181 Aiguaviva We, manufacturer of electric linear actuators, declare that our WARNING! RA-MINI Electric Linear Actuator Series Failure to follow these instructions can result in serious personal injury. -
Page 6: Warranty
RA-MINI PLAST45.30.89.350.D4 Customer Ref.: XXXXX 04.01. Warranty Exclusions Batch No: XXXXXX REGNER® is entitled to deny any warranty if: • The actuator has not been used correctly or its 01. RA-MINI PLAST 45.30.87.350.D4 usage specifications (load, temperature, duty cycle, • RA-MINI PLAST: actuator type voltage, current, etc.) have not been respected. - Page 7 RA-MINI PLAST IN-LINE ACTUATOR SERIES 05.02. Components 05.03. Specifications General Specifications 10, 30 or 50 mm Stroke 70 N at 3.5 mm/s Max. load 14.7 mm/s Max. speed (no load) 0.1 mm Backlash 12 VDC Power supply 114 mA Max. current 200 mA Starting current 116 mA...
- Page 8 RA-MINI PLAST IN-LINE ACTUATOR SERIES can resume its normal function and move freely in Preset Configurations either direction. High-speed Standard High-force reducer reducer reducer 05.07. Position feedback (opt.) (100:1) (210:1) (298:1) 20 N at 45 N at 70 N at Max. peak The position feedback potentiometer is feeded with a 9.0 mm/s 3.5 mm/s 3.6 mm/s...
-
Page 9: Installation
• Mounting pins must have the correct dimensions and limited free play. To install a REGNER® actuator, simply slip a pin • Any bolts and nuts used for the installation must through the hole on each end. Mounting pins must be made of high-quality steel. -
Page 10: Maintenance
RA-MINI PLAST IN-LINE ACTUATOR SERIES 07. Maintenance 06.02. Electrical Installation • Voltage must be switched off when the rod The actuator is a closed unit and does not require reaches the ends of the stroke or if an excessive internal maintenance. In fact, the actuator is not to load occurs mid-stroke to prevent damage to the be opened by unauthorized personnel. -
Page 11: Troubleshooting
09. Application Policy B. Run the actuator with REGNER® products can be used in a wide range of no load. applications in health care, household or industrial C. Please con- equipment, for example. REGNER® cannot know and tact REGNER®. - Page 12 RA-MINI PLAST IN-LINE ACTUATOR SERIES...
- Page 13 Ripollès, 4 | 17181 Aiguaviva (Girona) SPAIN | Tel. +34 972 476 911 | Fax +34 972 475 803 info@regner.es | www.regner.es...
Need help?
Do you have a question about the RA-MINI PLAST Series and is the answer not in the manual?
Questions and answers