Setup Instructions - Banzai AQUA SPORTS WATER PARK 90350 Manual

INTRODUCTION
Keep cool and play hard with this all-in-one backyard water park! The Aqua Sports
Water Park™ has 5 different activities that are sure to make a splash! Play hard in the
volleyball court, challenge your friends to a game of basketball, have a rematch with
water polo, then cool off by sliding down the giant water slide and getting drenched in
the Aqua Sports falls! With the included continuous airflow blower, all of this fun
inflates in under 3 minutes. Heavy-Duty Dura-Tech™ construction ensures lasting
strength and durability. With all this fun, you'll never want to leave your backyard!

SETUP INSTRUCTIONS

PLACEMENTS: Use on flat lawn only, not pavement or other hard surfaces. Lawn
should be free of rocks, bumps, depressions, sticks, etc. The product should be set up in a
location that has a minimum distance of 10 ft (305 cm) from any free standing structures
or obstructions, including: houses, garages, fences, trees, playground equipment, and
large rocks.
10 ft (305 cm)
WARNING:
Overfilling will cause damage to your ball.
This product is intended to be used as a toy
and not as a personal flotation device.
10 ft (305 cm)
safety area
10 ft (305 cm)
Inflate this product with AIR.
NOTE: For easy air inflation, use
a manual air pump designed
specifically for plastic inflatables.
1. Unfold the constant air inflatable in a desired position on a smooth and level surface.
2. Lay out the water hose assembly and match the number on each sprayer to the correct position on the arch of the
inflatable. Once the numbers are matched, attach the sprayers to the arch and corresponding position using the
Velcro patches provided. Secure the water tubing using the Velcro hooks & loops located on top of the arch, and
along the side of the inflatable. (Fig A1-A3)
3. Attach the long intake tube at the back of the inflatable to the mouth of the blower motor using the attached Velcro
strap. To ensure a secure fit, wrap the strap around the mouth of the blower and tightly attach the self-sticking strap.
(Fig A4-A6)
4. Use the drawstrings to tie shut the short air release tube along the back of the constant air inflatable.(Fig A7)
5. Position the blower in a straight line perpendicular and level to the back of the inflatable. The blower should be
placed on a stable surface
and remain upright after
the inflatable is inflated.
The blower is a
high-volume fan capable of
moving a lot of air very
quickly. Place the blower in
an area where it will not
suck in dirt or leaves. Keep
blower away from children,
water and moving vehicles.
Set up inflatable far away
from any structures or
obstructions. Once positioned, secure the blower with the blower ground stakes provided.(Fig A8)
6. Do not set up over concrete, asphalt, packed earth, or any other hard surfaces. A fall onto a hard surface can result
in serious injury.
7. Locate the loops around the bottom of the inflatable and anchor them to the turf, sand soil or rock soil with the water
slide ground stakes provided. (Fig A9)
8. Ground stakes must be completely inserted into the ground so that no part of the stake is protruding above the
ground surface. This will help prevent tripping or injuries resulting from a fall.
9. Plug the blower into a properly grounded outlet and turn it on. The inflatable should inflate in under 3 minutes. Do not
allow children to use the inflatable until it is fully inflated.
10. Close the water valve at the bottom of the pool. (Fig A10)
11. Fill the pool with at least 8 in (20 cm) of water before playing. Thoroughly wet all slide surfaces, platforms and
climbing walls before use to ensure optimal play performance.
12. Do not fill the product tub to more than the maximum fill line marked inside the pool wall.
13. After inflation, the blower should run continuously while children are playing.
FOR INFLATABLE BASKETBALL / WATER POLO / VOLLEYBALL:
14. Roll out the ball. Inspect for holes, tears or other damage. (Fig A11)
15. Inflate this product with AIR. (Fig A12)
NOTE: For easy air inflation, use a manual air pump designed specifically for plastic inflatables.
BY MOUTH: Remove the air valve plug and squeeze the base of the valve causing the inner flap to open for inflation.
BY PUMP: Remove the air valve plug and insert air pump nozzle into the valve. The air pump nozzle should be
inserted deep enough to open the inner valve flap.
Do not over inflate the item. Once the item is completely inflated, then insert the air valve plug to seal it shut.
NOTE: Fill inflatable with air until it is firm and solid. If there is any straining at the seams, the item is over inflated. If
any seam begins to strain, immediately stop inflation and release air to reduce the pressure until all signs of stress
on the inflatable are gone. DO NOT use the inflatable if there is straining at the seams. Use of an over-inflated item
may result in serious injury, paralysis or death.
Inspect this product for rips, tears or punctures. Do not use if
damaged.
16. Lay out the volleyball net and attach it to the pillar of the inflatable
using Velcro patches provided. (Fig A13)
Fig. A9 Fig. A10
SETUP
Fig. A1 Fig. A2
Fig. A4 Fig. A5
Fig. A7 Fig. A8
Fig. A11 Fig. A12 Fig. A13
OR OR
Fig. A3
Fig. A6
3
90350 Banzai