Advertisement
4. operaTioN
‰
warNiNG! ensure that you read, understand and apply the safety instructions in section 1.
‰
warNiNG! excess pressure can cause damage to paintwork and will put the polisher motor under strain. Polishers with burnt out
motors will be rejected as a warranty claim. Normally the weight of the polisher is sufficient.
‰
warNiNG! do not use the polisher with abrasive or rubbing compounds.
4.1.
Before each use, check that the bonnet is clean and free of abrasive particles and is undamaged and that the pad rotates freely.
4.2.
Apply a small amount of polish/wax evenly over the surface of the bonnet. do not apply polish directly to the vehicle surface.
4.3.
Hold the polisher firmly by the handles and place the polishing face onto the panel to be polished.
4.4.
start the polisher using the red on/off switch on the handle ensuring that the pad is still in contact with the vehicle panel.
4.5.
move the polisher with broad sweeping strokes over the surface in a criss cross pattern. do not apply pressure to the polisher when in
use. Work in logical areas and re-apply the polish/wax at intervals during the polish application process. do not allow the foam pad to
become saturated with polish/wax as this will make polishing more difficult and will reduce pad life.
4.6.
Polish/wax should be applied to difficult-to-reach areas by hand.
4.7.
switch off the polisher before lifting it from the panel when polish application is completed.
4.8.
remove the application bonnet and replace it with the wool bonnet.
4.9.
Buff the polish/wax in the same order it was applied. Do not put pressure on the polisher but allow its weight and action to do the job.
4.10.
Badly oxidised paint may require several applications. Do not use abrasive compounds.
4.11
if the polish/wax is difficult to buff too much has been applied. this may also cause the bonnet to come off the pad.
‰
warNiNG! Do not immerse the polisher in water.
5. maiNTeNaNce
5.1
Always store the polisher on its side so that the foam pad does not become compressed and/or distorted.
5.2
remove the bonnet when not in use to allow the foam pad to dry out.
5.3
clean the bonnet regularly by hand washing with soap and water. Do NoT immerse the foam pad in water. Washing the bonnet is
sufficient.
5.4
if the foam pad requires replacement return the unit to your local sealey as this is not a user servicable part.
parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
imporTaNT: no liability is accepted for incorrect use of this product.
warraNTy: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
01284 757500
01284 703534
er150P | issue 4 10/03/17
www.sealey.co.uk
sales@sealey.co.uk
Advertisement
