Advertisement
‰
warNiNG! Keep all guards and holding screws in place, tight and in good working order.
9
check regularly for damaged parts. A guard or any other part that is damaged must be repaired/replaced before the polisher is next
used.
9
use the polisher in a suitable work area and keep the area clean and tidy and free from unrelated materials. ensure that there is
adequate lighting.
9
Keep the polisher clean for best and safest performance.
9
Before each use check all attachments for condition. if worn or damaged replace immediately.
9
ensure that there are no flammable materials near the work area.
‰
warNiNG! Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
9
maintain correct balance and footing. ensure that the floor is not slippery and wear non-slip shoes.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Avoid unintentional starting.
8
Do NoT use the polisher for any purpose other than that for which it is designed.
8
Do NoT operate the polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Do NoT switch the polisher on until the head is in contact with the panel and switch the unit off before removing the head from the
panel.
8
Do NoT use the polisher with abrasive cleaners or rubbing compounds as excessive paint removal may result.
8
Do NoT get the polisher wet or use in damp or wet locations or areas where there is condensation.
8
Do NoT allow untrained persons to operate the polisher.
8
Do NoT operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do NoT use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
8
Do NoT leave the polisher operating unattended.
8
Do NoT carry the polisher with your finger on the power switch.
8
Do NoT pull the cord from the power supply.
9
use a qualified person to maintain the polisher.
9
When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
warNiNG! – risk of hand arm vibration injury.
this tool may cause Hand Arm Vibration syndrome if its use is not managed adequately.
this tool is subject to the vibration testing section of the machinery directive 2006/42/ec.
this tool is to be operated in accordance with these instructions.
measured vibration emission value (a)...........................17.03 m/s²
uncertainty value (k):......................................................6.8 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend
that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each
tool.
nB: stated Vibration emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
such factors include; the operator, the task and the inserted tool or consumable.
nB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
the state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be
modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPe) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and
dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the
correct use and maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on
the Hsc website www.hse.gov.uk - Hand-Arm Vibration at Work
2. iNTroDucTioN
random orbital polisher with Ø150mm 3 ply foam pad and two polishing bonnets. smooth operation provides even buffing/polishing with no hot
spots. impact resistant ABs housing with twin grips. supplied with 4mtr cable and Bs approved plug. Gs/tuV and ce approved.
3. specificaTioN
model no ................................................................... er150P
input ........................................................................230V 50Hz
Power ................................................................................ 60W
speed ......................................................................... 3800rpm
Pad size ........................................................................150mm
cable length ..................................................................... 4mtr
noise Power ............................................................... 61.9dB.A
noise Pressure ........................................................... 72.9dB.A
replacement Backing Pad ..................................... er150P.BP
replacement Bonnet terry cloth ........................... er150P.tB
replacement Bonnet synthetic Wool ....................er150P.WB
© Jack sealey limited
Original Language Version
er150P | issue 4 10/03/17
Advertisement
