Protecting The Environment - DeWalt D25481 Original Instructions Manual

symbol Mode
Rotary Drilling
Rotary
hammering
hammering only
To select an operating mode:
1. Depress the mode selector release button
2. Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
nOTE: The arrow on the mode selector dial
at a mode symbol at all times. There are no operable positions
in between. It may be necessary to briefly run the motor after
having changed from 'hammering only' to 'rotary' modes in
order to align the gears.
Performing an Application (Fig. A, E)

WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
1. Choose and install the appropriate chuck, adapter, and/or
bit onto to the tool. Refer to Bit and Bit Holder.
2. Using the mode selector dial
appropriate to desired application. Refer to
Operation Modes.
3. Adjust the side handle 2 as necessary.
4. Place the bit/chisel on the desired location.
5. Depress the trigger switch
6. To stop the hammer, release the switch.
Recommendations for Tool Operation
• When drilling, always apply pressure in a straight line with
the bit, but do not push hard enough to stall the motor or
deflect the bit. A smooth even flow of material indicates the
proper drilling rate.
• Your hammer can be used for dry diamond drilling into
masonry up to 100 mm. For diamond drilling above this
diameter in masonry and regular large diameter diamond
drilling in masonry and concrete, we advise the use of
a dedicated diamond core drill. Follow the core bit or
manufacturer's recommendations for using the accessory.
nOTE: Always use core bits with integral centredrill systems
and ensure the RPM (speed) of the hammer does not
exceed the maximum rated RPM of the diamond core.
- Insert the centredrill into its holder in the centre of the
core bit.
- Remove and unplug the machine.
- Remove the centredrill from its holder.
Plug the machine in and insert the core bit into
-
the workpiece.
Application
Dry diamond coring
Drilling into concrete and masonry
Light chipping
5 .
4 must be pointing
4 , select the mode
.
1

WARNING:
• Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir inflammable liquids
labelled accordingly.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Various types of SDS-Max bits and chisels are available as
an option. Accessories and attachments used must be regularly
lubricated around the SDS-Max fitment.
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
English
WALT recommended
e
7