Download
Share
Print this page
Otter Pro XT Lodge Installation And Setup Instructions
  1. Manuals
  2. Brands
  3. Otter Manuals
  4. Tent
  5. Pro XT Lodge
  6. Installation and setup instructions

Otter Pro XT Lodge Installation And Setup Instructions

Fits magnum otter ii & pro sled only
Hide thumbs

Advertisement

Quick Links

Download this manual
MODEL NUMBERS:
MODEL NUMBERS:
MODEL NUMBERS:
MODEL NUMBERS:
MODEL NUMBERS:
Complete Pkg Pro XT Thermal Lodge
Complete Pkg
Complete Pkg
Complete Pkg
Complete Pkg
Pro XT Thermal Lodge
Pro XT Thermal Lodge
Pro XT Thermal Lodge
Pro XT Thermal Lodge
P P P P P AR
ARTS LIST
AR
AR
AR
TS LIST
TS LIST
TS LIST
TS LIST
Item # Q t y
Item #
Item #
Item #
Item #
Q t y
Q t y
Q t y
Q t y
Part #
Part #
Part #
Part #
Part #
1
1
201067
2
1
200967
3
1
80172
4
1
80171
5
1
80517
6
1
80518
7
1
80519
8
1
80512
9
2
80470
10
2
80471
11
4
80472
12
2
80474
13
6
80473
14
4
80475
15
2
200861
16
2
200369
17
2
200806
18
1
200379
19
2
200196
20
2
200376
21
8
200384
22
16
400641
23
8
200197
24
8
200195
25
14
200615
26
8
200944
27
4
401017
28
16
400648
29
2
400367
30
2
200787
31
8
200235
32
12
200942
33
16
200941
34
16
200943
35
1
200976
24
25
26
Otter Pro XT Lodge
Installation and Set-Up Instructions
Otter Pro XT Lodge
Fits Magnum Otter II & Pro Sled Only
Parts Identification and Check List
200958
200958
200958
200958
200958
Description
Description
Description
Description
Description
Sled - Dark Gray
Tent - XT Thermal Lodge
Frame Bracket "A"
Frame Bracket "B"
Back Wind Support Bar - 49 1/2"
Center Wind Support Bar - 34 5/8"
Center Wind Support Bar - 44 3/4"
Adjustable Front Wind Support Bar
Main Frame Extension Bar - 31 1/2"
Main Frame Extension Bar - 32 1/2"
Main Frame Extension Bar - 30"
Outer Main Frame Bar - 33"
Outer Main Frame Bar - 29 9/16"
Middle Main Frame Bar - 52"
Seat
Seat Bracket
Seat Base
Seat Rail - 67"
Seat Rail Cap
Seat Rail Bracket
Sleeve
#8 x 3/4" Self Tapping Screw
Black Plug
Black End Cap
5/16 Washer
1/4 x 1/2 Philips Head, Counter Sunk Screw
1/4 x 3/4 Hex Bolt
1/4 Nylon Hex Lock Nut
5/16 x 2 Hex Bolt
5/16 Nylon Hex Lock Nut
1/4" Low Profile Nylon Lock Nut
3/8" Self Tapping Screw
Plastic Protector
Star Washer
Plastic Trim Lock Kit
27
28
29
30
3
6
11
Back &
Center
15
19
31
32
33
34
Page 1
1
4
5
7
Front
12
Front
10
All
14
9
Bottom
16
21
22
20
35
Instructions - 70761
2
8
Back
Center
13
Bottom
17
18
23

Advertisement

loading
Need help?

Need help?

Do you have a question about the Pro XT Lodge and is the answer not in the manual?

Questions and answers

Dan Albers
March 19, 2025

Can the lodge flip over be opened and held halfway to be used as a windblock?

0

Related Manuals for Otter Pro XT Lodge

Summary of Contents for Otter Pro XT Lodge

  • Page 1 Otter Pro XT Lodge Installation and Set-Up Instructions Otter Pro XT Lodge Fits Magnum Otter II & Pro Sled Only Parts Identification and Check List MODEL NUMBERS: MODEL NUMBERS: MODEL NUMBERS: MODEL NUMBERS: MODEL NUMBERS: Complete Pkg Complete Pkg Complete Pkg...
  • Page 2 Tools Required: Ratchet & 7/16” socket 7/16” wrench Short extension for Ratchet or 7//16” deep socket Drill/Driver Phillips Bit Phillips Screwdriver ½” Wrench ½” socket 5/16” Drill Bit 7/16” Drill Bit Installing the seating system before assembling the frame and canvas will make installation easier.
  • Page 3 2. Slide brackets and swivel part way onto the plastic base. Adjust the fit to be snug by pressing in on the brackets. However the brackets still need to be able to slide smoothly back and forth on the plastic base. Tighten the bolts securely once the fit is correct. Press in on slide Tighten all 4 nylock brackets and adjust...
  • Page 4 4. Drill out the four pre-marked holes for the seat rail brackets as shown using a 5/16” drill bit. The sled may be tipped upside down to make drilling the holes easier. Drill four pre-marked holes at these locations. Drill these 2 pre-marked holes with Drill these 2 pre-marked holes with a 5/16 drill bit.
  • Page 5 Install plastic end caps here. Secure with ¾” self tapping screws. 6. After the brackets and end caps are installed the seat rail may be bolted into place with the ¼” bolts, washers and nylock nuts using the previously drilled holes. Install plastic base and seat onto the rail.
  • Page 6 Seat assembly not shown for clarity. 7. Position sled (Item 1) as shown in Diagram 7 with curved front to your left. 8. Drill the 4 marked holes using a 5/16” bit. 9. Drill the 7/16” hole in center of lip approximately 16” from bend in sled. The back wind support bar (Item 5 not shown) is to be propped here.
  • Page 7 11. Assemble Back and Center Main Frame Bars: Insert the outer main frame bar (Item 13) into the middle main frame bar (Item 14). Fasten with self-tapping screw (Item 22), plastic protector (Item 33), and star washer (Item 34). Slide the sleeve (Item 21) over the main frame extension bar (Item 11). (Line up holes with button lock, press lock in as you slide over the bar).
  • Page 8 13. Assemble Front Main Frame Bar: Insert the outer main frame bar (Item 12) into the middle main frame bar (Item 14). Fasten with self-tapping screw (Item 22), plastic protector (Item 33), and star washer (Item 34). Slide the sleeve (Item 21) over the main frame extension bar (Item 10). (Line up holes with button lock, press lock in as you slide over the bar).
  • Page 9 15. Assemble Bottom Main Frame Bar: Insert the outer main frame bar (Item 13) into the middle main frame bar (Item 14). Fasten with self-tapping screw (Item 22), plastic protector (Item 33), and star washer (Item 34). Slide the sleeve (Item 21) over the main frame extension bar (Item 9). (Line up holes with button lock, press lock in as you slide over the bar).
  • Page 10 17. Set up main frame bars by grasping with both hands and pushing upward until button clicks into place. Start with bottom main frame bar and continue to the back main frame bar pushing lengthened bars into appropriate position Ref. Diagram 15. Center Main Diagram 15 Frame Bar...
  • Page 11 19. Slide the tent over the main frame bar Diagram 17 assembly, then fasten the velcro straps on the inside of the tent to each main frame bar. Ref. Diagram 17. Tent Note: Collapsing the center and front main frame poles part way down will make installation easier.
  • Page 12 21. On the front of the fishhouse, start in the corners and work inward, snap the plastic trim seal on the canvas tent (Item 2) to the lip edge of the sled (Item 1). The tent (Item 2) will meet in the middle and should be free to open and close so it can be removed.Ref.
  • Page 13 Otter Outdoors Inc. 411 W Congress St. • Maple Lake, MN 55358 Otter Pro XT Lodge Phone 320-963-6480 • www.otteroutdoors.com October, 2015 Page 12...