Advertisement
6.2.5.
to remove attachment, reverse procedures 6.1. and 6.2. using pressure on tag A.
Fig.3
7. sa21/s - air ratchet wreNch
the air ratchet wrench has a hardened steel anvil with trigger operated power control, it is suitable for use in the engine bay where there is
limited space for hand operated ratchets.
warNiNG! ensure that you read, understand and apply the safety instructions in section 1 before use. additionally the
‰
following safety instructions are specific to this tool.
Do Not use any additional force upon the wrench in order to remove or tighten a nut.
8
7.1.
Only use sockets specifically designed for use with a ratchet wrench.
7.2.
operation
7.3.
connect the wrench to the air supply as in section 4.
7.4.
Place the socket over the subject nut and depress the trigger to operate the wrench.
7.5.
to change ratchet direction turn the switch on the tool head. f = forward r = reverse.
7.6.
The flow of air (torque) may be regulated by turning the screw above the trigger.
8. sa67 - air Die GriNDer
one-handed straight type die grinder with aluminium body and trigger with safety catch. chuck accepts grinding bits with Ø6mm
shanks.
warNiNG! ensure that you read, understand and apply the safety instructions in section 1 before use. additionally the
‰
following safety instructions are specific to this tool.
warNiNG! Do Not grind any materials containing asbestos.
‰
warNiNG! Before each use check grinding bit is secure, and the bit is not worn or damaged, if damaged, replace immediately.
‰
Always use the correct grinding bit suitable for the material being ground. ensure the maximum speed specification of the bit is higher
9
than that indicated on the machine data plate.
Avoid subjecting grinding bit to excessive strain, hold grinder firmly and always ease grinding bit against workpiece (a harsh impact may
9
break the bit). maintain a controlled progression.
Do Not turn the die grinder on whilst the grinding bit is in contact with the workpiece.
8
Do Not use die grinder where there are flammable liquids, solids or gases such as paint solvents, including waste wiping or cleaning
8
rags etc. as generated sparks may be dangerous.
Do Not touch the workpiece close to the ground surface as it will be very hot. Allow to cool. the workpiece may also be very sharp.
8
8.1.
operation
8.2.
check that grinding bits are not damaged in any way such as cracks, deformations or splinters etc. damaged bits must not be used.
8.3.
use wrenches provided to loosen collet locking collar. insert grinding bit and re-lock collar.
8.4.
connect the air die grinder to the air supply as in section 4.
8.5.
to start, hold firmly and push the trigger locking lever forward whilst depressing trigger.
8.6.
the bit must be running at its maximum speed before attempting to grind the workpiece.
8.7.
slowly and smoothly bring the grinding stone toward the workpiece (avoid jerky movements).
8.8.
exert adequate pressure on the die grinder to grind according to the type and size of the material you are working with. Avoid subjecting
bit to excessive strain or harsh impacts.
9. MaiNteNaNce
warNiNG! disconnect the tool from the air supply before changing accessories, servicing or performing maintenance.
‰
9.1.
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9.2.
if the air supply does not have an oiler, lubricate the air tool daily with a few drops of sealey air tool oil dripped into the air inlet to prolong its
life.
9.3.
clean the tool after use.
9.4.
loss of power or erratic action may be due to the following:
a) excessive drain on the air line. moisture or restriction in the air pipe. incorrect size or type of hose connectors. to remedy check the
air supply and follow instructions in section 4.
b) Grit or gum deposits in the wrench may also reduce performance. if your model has an air strainer (located in the area of the air
inlet), remove the strainer and clean it. flush the wrench out with gum solvent oil or an equal mixture of sAe no 10 oil and paraffin.
Allow to dry before use.
9.5.
for a full service contact your local sealey service agent.
9.6.
When not in use, disconnect from air supply, clean tool and store in a safe, dry, childproof location.
impact wrench only - check and top up the gearbox oil by removing grub screw located on the right side, above the grip.
9.7.
© Jack sealey limited
Fig.4
s
Original Language Version
sA2004Kit.V2 | issue 1 17/11/16
Advertisement
