Advertisement
Air hammer medium stroke:
speed: .......................................................................... 4500rpm
stroke: .............................................................................. 43mm
chisel shank:............................................................ .401" round
Vibration: ........................................................................ 9.4m/s²
uncertainty: .................................................................... 1.5m/s²
noise power: ...................................................................... 96dB
noise pressure: .................................................................. 85dB
4. preparatioN For use
4.1.
recommended hook-up is shown in fig.1.
warNiNG! ensure that the air supply is clean and does not exceed 90 psi while operating these tools. too much air pressure and/or
‰
unclean air will cause excessive wear and may be dangerous, causing damage and/or personal injury.
4.2.
ensure that the tool trigger is not depressed before connecting to the air supply.
4.3.
You will require an air pressure of 90psi, and an air flow of 4cfm per tool.
4.4.
drain the air tank daily. Water in the air line will damage the tools and invalidate your warranty.
4.5.
clean the compressor air inlet filter weekly.
4.6.
line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum hose bore should be 1/4"
and fittings must have the same inside dimensions.
4.7.
Keep hoses away from heat, oil and sharp edges. check hoses for wear and make certain that all connections are secure.
4.8.
couplings - vibration may cause failure of a quick change coupling that is connected directly to the air tools.
4.8.1.
to overcome this, connect a leader hose (sealey model number AH2r) to the tools.
4.8.2.
A quick change coupling may then be used to connect the leader hose to the air line recoil hose. see figs.1 & 2.
5. sa2 - air iMpact wreNch
tough professional air impact wrench with fully polished alloy housing and rubber bumper. through type forward/reverse control. 4 position
adjustable air/torque selection. fitted with standard 1/2" square drive. fitted with rocking-dog type clutch and hardened impact anvil. suitable for
general garage use.
warNiNG! ensure that you read, understand and apply the safety instructions in section 1 before use. additionally the
‰
following safety instructions are specific to this tool.
5.1.
use only impact sockets, since these are specifically designed for use with an impact wrench. standard sockets may shatter.
Do Not use any additional force upon the wrench in order to tighten or remove a nut.
8
5.2.
take care not to over-tighten fixings.
5.3.
operation
5.3.1.
connect the wrench to the air supply as in section 4.
5.3.2.
fit a socket onto the square drive and then place the socket over the nut. squeeze the trigger to operate the wrench.
5.3.3.
to change direction push the button at the top of the handle, direction "f" for forward and "r" for reverse.
5.3.4.
The flow of air (torque) may be regulated by adjusting flow valve at the base of the handle, push in the adjuster and turn clockwise until
correct setting (1 to 4) is reached, then let adjuster click out to lock.
6.
sa12/s - air haMMer
the air hammer is designed primarily for use on vehicle bodywork. We do not recommend any other use.
warNiNG! ensure that you read, understand and apply the safety instructions in section 1 before use. additionally the
‰
following safety instructions are specific to this tool.
6.1.
ensure chisels are correctly rated for the job. Do Not use damaged or suspect chisels.
Do Not switch the hammer on whilst the chisel is in contact with the workpiece.
8
Do Not use hammer where there is flammable liquid, solids or gas such as paint solvent, including waste wiping or cleaning rags etc.
8
warNiNG! Do Not chisel any materials containing asbestos.
‰
6.2.
operation
6.2.1.
insert the chisel shank into the gun cylinder (fig.3).
6.2.2.
Place the retainer ring over the chisel (fig.3) and lower onto the hammer's cylinder thread. screw the retainer spring on to the cylinder
using a clockwise motion and using pressure on tag B until the spring is fully located (fig.4) and the chisel is retained by the spring retaining
tag (B).
6.2.3.
connect the hammer to the air supply as in section 4.
6.2.4.
to operate the hammer, squeeze the trigger, taking care that the chisel end is not in contact with the work-piece. the air regulator can be
adjusted by means of the knob at the base of the handle, use this as a means of throttle control.
© Jack sealey limited
sockets:
sizes: ................................. 9, 10, 11, 13, 14, 17, 19, 22, 24, 27
extension bar: .................................................................. 75mm
Adaptor: .................................................3/8"sq. (m) x 1/2"sq. (f)
Original Language Version
Fig.1
sA2004Kit.V2 | issue 1 17/11/16
Fig.2
Advertisement
