Sealey SA1003 Manual

Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAfeTy
1.1. OperATiOnAl SAfeTy
WArninG! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
WArninG! disconnect from air supply before changing accessories or servicing.
‰
Maintain the sander in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable clean and tidy work area and ensure there is adequate lighting.
9
Before each use check abrasive pads for condition. If worn or damaged replace immediately.
9
ensure the abrasive pad rating is the same as, or, greater than the RPM rating of the sander.
9
Ensure there are no flammable or combustible materials near the work area.
9
WArninG! Always wear approved eye or face and hand protection when operating the sander.
‰
Use face, dust, or respiratory protection in accordance with CoSHH regulations.
9
depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
9
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the sander. never hold a workpiece by hand.
9
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
9
Avoid unintentional starting.
9
WArninG! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
9
secure.
Prolonged exposure to vibration from this sander poses a health risk. It is the owner's responsibility to correctly assess the potential
9
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
dO nOT use the sander for a task it is not designed to perform.
8
dO nOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WArninG! dO nOT sand any materials containing asbestos.
‰
dO nOT carry the sander by the hose, or yank the hose from the air supply.
8
dO nOT force, or apply heavy pressure to the sander, let the sander do the work.
8
dO nOT place air line attachments close to your face and dO nOT point at other persons or animals.
8
dO nOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
dO nOT use sander where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or
8
cleaning rags etc.
dO nOT carry the sander with your finger on the power lever.
8
dO nOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
© Jack Sealey limited
Ø50mm mini Air SAnder
Model no:
Wear protective Wear ear
gloves protection
Original Language Version
SA1003
Wear a mask
SA1003 Issue 2 (3) 18/12/19