Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maretron TSM1330C
Summary of Contents for Maretron TSM1330C
- Page 1 TSM1330C 13.3” Vessel Monitoring and Control Touchscreen User’s Manual Revision 1.0 Copyright © 2014 Maretron, LLP All Rights Reserved Maretron, LLP 9014 N. 23 Ave #10 Phoenix, AZ 85021-7850 http://www.maretron.com Maretron Manual Part #: M003054 Revision 1.0 Page i...
- Page 2 TSM1330C User's Manual Revision History Rev. Description Original document Page ii Revision 1.0...
-
Page 3: Table Of Contents
Manually Entering LAN Connection Information ............15 Operating the TSM1330C ......................18 Turning the TSM1330C On ....................18 Turning the TSM1330C Off ....................18 Adjusting the Screen Brightness on the TSM1330C ............18 Using the TSM1330C ....................... 18 Maintenance ..........................19 Troubleshooting ........................... 20 Mechanical Drawings ........................ - Page 4 Table of Figures Figure 1 – TSM1330C Network Diagram ....................1 Figure 2 – TSM1330C Cutout Dimensions (units in mm [inches]) ............7 Figure 3 – TSM1330C VESA Arm Mounting Retention Screw Holes ............ 8 Figure 4 – TSM1330C Interface Connector Panel ................9 Figure 5 –...
-
Page 5: General
The TSM1330C is ruggedized for marine use and includes a solid state disk drive to withstand the pounding associated with waves. And since the TSM1330C only dissipates 20 watts, there is no need for internal cooling fans that are noisy and wear out causing electronics to overheat and fail. -
Page 6: Firmware Revision
TSM1330C User's Manual instructions for installation, configuration, and usage of the Maretron TSM1330C in order to ensure optimal performance. Firmware Revision ® This manual corresponds to the TSM1330C running N2KView Version 4.0.2. TSM1330C Features NOTE Although the TSM1330C looks similar to the former TSM1330 product, there are ®... - Page 7 Unpacking the Box (Section 2.1) Choosing a Mounting Location (Section 2.2) Mounting the TSM1330C (Section 2.3) Connecting the TSM1330C (Section 2.4) Configuring the TSM1330C (Section 2.6) Revision 1.0 Page 3...
-
Page 8: Installation
Choosing a Mounting Location The TSM1330C front panel is splash proof (IEC IP66 rating – protected against the effects of powerful water jets), while the rear of the TSM1330C is drip proof (IEC IP22 rating – protected Page 4 Revision 1.0... -
Page 9: Mounting The Tsm1330C
15°). The TSM1330C may be mounted either in an indoor or outdoor location. Adequate ventilation is a necessary prerequisite for the life of the product. The air inlet and outlet openings must definitely be kept clear;... -
Page 10: Ergonomics
The classification is only valid for approved mounting brackets provided by Maretron. The unit shall be mounted stand-alone without any devices or loose parts placed at or nearby the unit. Any other type of mounting might require test and re-classification. - Page 11 Step 2: Cut out a section from the panel that corresponds to the rear panel dimensions of the TSM1330C. Take care that the panel section that is cut out is smaller than the overall size of the front panel of the TSM1330C but just large enough for the rear panel of the TSM1330C to fit through, according to the dimensions in Figure 2 above.
-
Page 12: Arm Mounting
TSM1330C User's Manual 2.3.3 Arm Mounting The TSM1330C is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 75mm interface pad. To mount the TSM1330C on an arm, please follow the steps below. NOTE When purchasing a mounting arm please ensure that it is VESA compliant and that the arm has a 75 mm interface pad. -
Page 13: Connecting The Tsm1330C
Connecting the TSM1330C Most I/O interface connections of the TSM1330C are found on the bottom panel. The I/O interface panel located on the bottom of the TSM1330C has the following I/O interface connectors: 2 x 24V DC Power input connector ... -
Page 14: Lan Connection
LAN cable with an RJ-45 connector, please follow the instructions below. Step 1: Locate an RJ-45 connector on the bottom panel of the TSM1330C. Step 2: Align the connector. Align the RJ-45 connector on the LAN cable with the RJ-45 connector on the bottom panel of the TSM1330C. -
Page 15: Usb Device Connection
TSM1330C. Install the included waterproof USB bulkhead connector in a position where it is easily accessible and plug into one of the USB connectors on the TSM1330C per the instructions below. This will make the USB connection easily accessible once the TSM1330C is installed. -
Page 16: Power Connection
Figure 7 – USB Device Connection 2.4.3 Power Connection The TSM1330C must be connected to a power source (over current protection should be provided and should be sized in accordance with ABYC E-11, AC and DC ELECTRICAL SYSTEMS ON BOATS). The TSM1330C provides two sets of independent, galvanically isolated power connections and can run off the power supplied by either connection, allowing for redundant power connection. -
Page 17: Grounding Screw
Maretron NMEA 2000 cable (or an NMEA 2000 compatible cable) by connecting the female end of the cable to the TSM1330C (note the key on the male connector and keyway on the female connector). Be sure the cable is connected securely and that the collar on the cable connector is tightened firmly. -
Page 18: Power Sequencing
When the TSM1330C is connected to an appropriate power source, you can use the power switch located on the front panel to turn the TSM1330C on or off. If the TSM1330C is turned on, then the switches found on the front panel will be illuminated. If the power switch is pushed to power down the TSM1330C, the front panel switches will be dark. -
Page 19: Manually Entering Lan Connection Information
Assigning a unique name to the TSM1330C is necessary in order to help you determine the source of alerts generated by a TSM1330C or other Maretron device capable of generating alerts. - Page 20 If your local area network uses a DHCP server, no configuration is necessary, and the TSM1330C should be able to successfully connect to the local area network. If your local area network does not use DHCP, you must manually enter the LAN connection information into the TSM1330C.
- Page 21 Figure 13 – Configuration Dialog, Network Tab Uncheck the “Use DHCP” box to indicate that your LAN does not use DHCP. Optionally, in the “Hostname” field, enter a hostname for the TSM1330C. This is used by the network router. In the “IP Address” field, enter the IP address you wish to assign to the TSM1330C.
-
Page 22: Operating The Tsm1330C
3 Operating the TSM1330C Turning the TSM1330C On To turn on the TSM1330C, press the power button, located underneath the screen on the front of the TSM1330C for at least one second. The power button backlights will change from dim to bright once the power-on process begins. -
Page 23: Maintenance
Ensure that the unit is mounted securely and cannot be moved relative to the mounting surface. If the unit is loose, tighten the mounting screws. Check the security of the power and network cables connected to the TSM1330C and tighten if necessary. -
Page 24: Troubleshooting
TSM1330C will expose the sensitive electronic components to adverse environmental conditions that may render the unit inoperative. Please do not open the TSM1330C, as this will automatically void the warranty. If service is required, please return the unit to an authorized Maretron service location. -
Page 25: Mechanical Drawings
6 Mechanical Drawings TSM1330C 248.5mm 9.78” 355mm 13.98” 58mm 2.28” 52mm 2.05” Revision 1.0 Page 21... -
Page 26: Technical Specifications
LCD Color 262K Viewing Angle 70° H, 60° V Buzzer 85dB USB Ports Two USB 2.0 Ethernet Ports One RJ-45 GbE For connection to Maretron IPG100 or router Compass Safe Distance 45cm Standard 25cm Steering Approvals Parameter Comment IEC 60945 GL –... - Page 27 Mechanical Parameter Value Comment 2.28” x 13.98” x 9.78” Overall Dimensions (DxWxH) (58mm x 355mm x 248.5mm) Weight 9.7 lbs (4.4kg) Front Panel Material Glass Front Panel Controls Power, Brightness +/- Mounting 4 x M4 VESA Mounting Max 8mm deep 75mm x 75mm Built-in Console 4 x M5 x 15mm screws...
-
Page 28: Technical Support
TSM1330C User's Manual 8 Technical Support If you require technical support for Maretron products, you can reach us in any of the following ways: Telephone: 1-866-550-9100 Fax: 1-602-861-1777 E-mail: support@maretron.com World Wide Web: http://www.maretron.com Mail: Maretron, LLP Attn: Technical Support 9014 N. -
Page 29: Maretron (1 Year) Limited Warranty
Maretron (1 Year) Limited Warranty Maretron warrants the TSM1330C to be free from defects in materials and workmanship for one (1) year from the date of original purchase. If within the applicable period any such products shall be proved to Maretron’s satisfaction to fail to meet the above limited warranty, such products shall be repaired or replaced at Maretron’s option. - Page 30 TSM1330C User's Manual Warranty Return Procedure: To apply for warranty claims, contact Maretron or one of its dealers to describe the problem and determine the appropriate course of action. If a return is necessary, place the product in its original packaging together with proof of purchase and send to an Authorized Maretron Service Location.
Need help?
Do you have a question about the TSM1330C and is the answer not in the manual?
Questions and answers