Maretron TSM800C User Manual

8" vessel monitoring and control touchscreen
Hide thumbs Also See for TSM800C:

Advertisement

Quick Links

TSM800C
8" Vessel Monitoring and Control
Touchscreen
User's Manual
Revision 1.0
Copyright © 2014 Maretron, LLP All Rights Reserved
Maretron, LLP
rd
9014 N. 23
Ave #10
Phoenix, AZ 85021-7850
http://www.maretron.com
Maretron Manual Part #: M003053
Revision 1.0
Page i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TSM800C and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Maretron TSM800C

  • Page 1 TSM800C 8” Vessel Monitoring and Control Touchscreen User’s Manual Revision 1.0 Copyright © 2014 Maretron, LLP All Rights Reserved Maretron, LLP 9014 N. 23 Ave #10 Phoenix, AZ 85021-7850 http://www.maretron.com Maretron Manual Part #: M003053 Revision 1.0 Page i...
  • Page 2 TSM800C User's Manual Revision History Rev. Description Original document Page ii Revision 1.0...
  • Page 3: Table Of Contents

    Manually Entering LAN Connection Information ............15 Operating the TSM800C ......................18 Turning the TSM800C On ....................18 Turning the TSM800C Off ....................18 Adjusting the Screen Brightness on the TSM800C ............18 Using the TSM800C ......................18 Maintenance ..........................19 Troubleshooting ........................... 20 Mechanical Drawings ........................
  • Page 4 Table of Figures Figure 1 – TSM800C Network Diagram ....................1 Figure 2 – TSM800C Cutout Dimensions (units in mm [inches]) ............7 Figure 3 – TSM800C VESA Arm Mounting Retention Screw Holes ............8 Figure 4 – TSM800C Bottom Panel ...................... 9 Figure 5 –...
  • Page 5: General

    The TSM800C is ruggedized for marine use and includes a solid state disk drive to withstand the pounding associated with waves. And since the TSM800C only dissipates 20 watts, there is no need for internal cooling fans that are noisy and wear out causing electronics to overheat and fail.
  • Page 6: Firmware Revision

     2 isolated NMEA 2000 ® ® connectors for direct connection to single or dual NMEA 2000 networks Quick Install Installing the Maretron TSM800C display involves the following five steps. Please refer to the individual sections for additional details. Page 2 Revision 1.0...
  • Page 7  Unpacking the Box (Section 2.1)  Choosing a Mounting Location (Section 2.2)  Mounting the TSM800C (Section 2.3)  Connecting the TSM800C (Section 2.4)  Configuring the TSM800C (Section 2.6) Revision 1.0 Page 3...
  • Page 8: Installation

    Choosing a Mounting Location The TSM800C front panel is splash proof (IEC IP66 rating – protected against the effects of powerful water jets), while the rear of the TSM800C is drip proof (IEC IP22 rating – protected against the Page 4...
  • Page 9: Mounting The Tsm800C

    15°). The TSM800C may be mounted either in an indoor or outdoor location. Adequate ventilation is a necessary prerequisite for the life of the product. The air inlet and outlet openings must definitely be kept clear; coverings which restrict ventilation are not permissible.
  • Page 10: Ergonomics

    The classification is only valid for approved mounting brackets provided by Maretron. The unit shall be mounted stand-alone without any devices or loose parts placed at or nearby the unit. Any other type of mounting might require test and re-classification.
  • Page 11: Figure 2 - Tsm800C Cutout Dimensions (Units In Mm [Inches])

    TSM800C. Take care that the panel section that is cut out is smaller than the overall size of the front panel of the TSM800C but just large enough for the rear panel of the TSM800C to fit through, according to the dimensions in Figure 2 above.
  • Page 12: Arm Mounting

    2.3.3 Arm Mounting The TSM800C is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 75mm interface pad. To mount the TSM800C on an arm, please follow the steps below. NOTE When purchasing a mounting arm please ensure that it is VESA compliant and that the arm has a 75 mm interface pad.
  • Page 13: Connecting The Tsm800C

    Connecting the TSM800C Most I/O interface connections of the TSM800C are found on the bottom panel. The I/O interface panel located on the bottom of the TSM800C has the following I/O interface connectors:  2 x 24V DC Power input connector ...
  • Page 14: Lan Connection

    LAN cable with an RJ-45 connector, please follow the instructions below. Step 1: Locate an RJ-45 connector on the bottom panel of the TSM800C. Step 2: Align the connector. Align the RJ-45 connector on the LAN cable with the RJ-45 connector on the bottom panel of the TSM800C.
  • Page 15: Usb Device Connection

    TSM800C. Install the included waterproof USB bulkhead connector in a position where it is easily accessible and plug into one of the USB connectors on the TSM800C per the instructions below. This will make the USB connection easily accessible once the TSM800C is installed.
  • Page 16: Power Connection

    Figure 7 – USB Device Connection 2.4.3 Power Connection The TSM800C must be connected to a power source (over current protection should be provided and should be sized in accordance with ABYC E-11, AC and DC ELECTRICAL SYSTEMS ON BOATS).
  • Page 17: Grounding Screw

    Maretron NMEA 2000 cable (or an NMEA 2000 compatible cable) by connecting the female end of the cable to the TSM800C (note the key on the male connector and keyway on the female connector). Be sure the cable is connected securely and that the collar on the cable connector is tightened firmly.
  • Page 18: Power Sequencing

    When the TSM800C is connected to an appropriate power source, you can use the power switch located on the front panel to turn the TSM800C on or off. If the TSM800C is turned on, then the switches found on the front panel will be brightly illuminated. If the power switch is pushed to power down the TSM800C, the front panel switches will be dim.
  • Page 19: Manually Entering Lan Connection Information

    Assigning a unique name to the TSM800C is necessary in order to help you determine the source of alerts generated by a TSM800C or other Maretron device capable of generating alerts.
  • Page 20: Figure 12 - N2Kview Window With Tabs Displayed

    If your local area network uses a DHCP server, no configuration is necessary, and the TSM800C should be able to successfully connect to the local area network. If your local area network does not use DHCP, you must manually enter the LAN connection information into the TSM800C.
  • Page 21: Figure 13 - Configuration Dialog, Network Tab

    Figure 13 – Configuration Dialog, Network Tab Uncheck the “DHCP” box to indicate that your LAN does not use DHCP. Optionally, in the “Hostname” field, enter a hostname for the TSM800C. This is used by the network router. In the “IP Address” field, enter the IP address you wish to assign to the TSM800C.
  • Page 22: Operating The Tsm800C

    3 Operating the TSM800C Turning the TSM800C On To turn on the TSM800C, press the power button, located underneath the screen on the front of the TSM800C for at least one second. The power button backlights will change from dim to bright once the power-on process begins.
  • Page 23: Maintenance

     Ensure that the unit is mounted securely and cannot be moved relative to the mounting surface. If the unit is loose, tighten the mounting screws.  Check the security of the power and network cables connected to the TSM800C and tighten if necessary.
  • Page 24: Troubleshooting

    TSM800C will expose the sensitive electronic components to adverse environmental conditions that may render the unit inoperative. Please do not open the TSM800C, as this will automatically void the warranty. If service is required, please return the unit to an authorized Maretron service location.
  • Page 25: Mechanical Drawings

    6 Mechanical Drawings TSM800C 166mm 6.54” 236mm 9.29” 236mm 51mm 9.29” 2.01” 45mm 1.77” Revision 1.0 Page 21...
  • Page 26: Technical Specifications

    LCD Color 262K Viewing Angle 70° H, 60° V Buzzer 85dB USB Ports Two USB 2.0 Ethernet Ports One RJ-45 GbE For connection to Maretron IPG100 or router Compass Safe Distance 45cm Standard 25cm Steering Approvals Parameter Comment IEC 60945 GL –...
  • Page 27 Mechanical Parameter Value Comment 2.01” x 9.29” x 6.54” Overall Dimensions (DxWxH) (51mm x 236mm x 166mm) Weight 4.2 lbs (1.9kg) Front Panel Material Glass Front Panel Controls Power, Brightness +/- Mounting 4 x M4 VESA mounting Max 8mm deep 75mm x 75mm Built-in console Mounting 4 x M5 x 15mm screws...
  • Page 28: Technical Support

    TSM800C User's Manual 8 Technical Support If you require technical support for Maretron products, you can reach us in any of the following ways: Telephone: 1-866-550-9100 Fax: 1-602-861-1777 E-mail: support@maretron.com World Wide Web: http://www.maretron.com Mail: Maretron, LLP Attn: Technical Support 9014 N.
  • Page 29: Maretron (1 Year) Limited Warranty

    Maretron (1 Year) Limited Warranty Maretron warrants the TSM800C to be free from defects in materials and workmanship for one (1) year from the date of original purchase. If within the applicable period any such products shall be proved to Maretron’s satisfaction to fail to meet the above limited warranty, such products shall be repaired or replaced at Maretron’s option.
  • Page 30 TSM800C User's Manual Warranty Return Procedure: To apply for warranty claims, contact Maretron or one of its dealers to describe the problem and determine the appropriate course of action. If a return is necessary, place the product in its original packaging together with proof of purchase and send to an Authorized Maretron Service Location.

Table of Contents