CognitiveTPG A798II Setup Manual page 2

3
Choose a location for the printer.
4
Connect the following cables based on your configuration, using a-b below.
Connector
When using USB (step "b" below),
Interface
Panel
use caution to ensure the USB
cable is connected to the USB
connector on the back left of
the printer and not into the
cash drawer connector that is
on the back right of the printer.
a
Cash drawer (if your installation includes this feature, page 15).
b
9-pin or 25 pin Serial or USB cable (serial: page 16; USB: page 17).
c
Connect the power cable (page 18).
d
Route cables as shown for your setup configuration (page 19).
5
Run a diagnostic test (page 19).
Open
Cover
Power
Supply
Connector
RS-232C
USB Cash
Communication
Connector Drawer
Connector
Connector
Push and hold
Paper Feed Button
while closing Cover
6
Configure the printer if necessary (page 20).
*** A798II - Diagnostics Form ***
Model number : A798-780X-TD00
Serial number : 0000000000
Loader Firmware
P/N : PN#: 189-799L111
Date : Nov 10 2015
Flash Firmware
Revision : V1.46
CRC : 9701
P/N : 189-798A146B
H/W parameters
Flash Memory Size : 8 Mbytes
Flash Logos/Fonts : 1600 kbytes
Flash User Storage : 576 kbytes
Flash Perm'nt Fonts : 2240 kbytes
Flash Journal Size : 640 kbytes
SRAM Size : 512 kbytes
Head settting : H
Motor ID : 1
Paper Type Setting : Type 0, Monochrome
Color Density Adj : n/a
Print Density, Mono : 100%
Max Speed : 180 mm/sec
Paper Width : 80 mm
Max Power : Level 1
Knife : Enabled
Partial Cut : 135 steps
Paper Low Sensor : Enabled
No Paper Low Extension
Comm. Interface
Interface : USB
RX Bu er Size : 4096
USB Driver Type : Printer Class
Interface : RS232
RX Bu er Size : 4096
Parameters
Baud Rate : 115200
Data Bits : 8
Stop Bit : 1
Parity : NONE
Flow Control : DTR/DSR
Reception Errors : Ignore
Resident Code Pages : 437, 720, 737, 775, 850
852, 857, 858, 860, 862...
***To Enter Printer Con g Menu***
Press Feed Button Within the
Next Two Seconds
DECLARATION OF CONFORMITY
Model: A798-XXXX-XXXX
Model: A799-XXXX-XXXX (X = any alphanumeric character)
CognitiveTPG, LLC, 950 Danby Road, Ithaca, New York, 14850
This declaration of conformity is issued under the sole responsibility of the Manufacturer: CognitiveTPG, LLC
Information Technology Equipment – Thermal Printer
The object of the declaration described above is in conformity with Directive 2011/65/EU of the European Parliament and
of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic
equipment. With the exception of models A798-XXXP-XXXX and A799-XXXP-XXXX
Applicable EU Directives:
2004/108/EC (electromagnetic compatibility directive)
2006/95/EC (low voltage directive for product safety)
Harmonized Standards:
EN 50581:2012 Technical documentation for the assessment of electrical and electronic products with respect to the
restriction of hazardous substances
EN 55024:2010 Information Technology Equipment Immunity Characteristics
EN 55022:2010/AC:2011 EMC, Class B, Limits and Methods of Measurement of Interference
Characteristics of IT Equipment
EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011
IEC 60950-1 (ed.2);am1- Product Safety Standard.
Signed for and on behalf of CognitiveTPG, LLC
Ithaca, NY, March 20, 2013
Jeffrey C Phoenix, Regulatory Compliance Engineer, CognitiveTPG, LLC
- Set Firmware Features - > 8 clicks
When the printer is configured for USB, this
location will show either: "USB Driver Type:
Printer Class", or "USB Driver: Comm Class".
Print Test and Configuration Menu Sample.
Samples will vary depending on the printer model.
Ref #: 189-1300058 Rev K