Advertisement
Locate the drill in a suitable working area, keep area clean and tidy and free from unrelated
3
materials. Ensure there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
3 Avoid unintentional starting.
DO NOT use drill for a task it is not designed to perform.
7
DO NOT allow untrained persons to operate the drill.
7
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate the drill if damaged.
7
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential
7
hazard. Keep flammable material away from the drill when operating. Flammable waste, such as
wipes or cleaning rags, must be placed in a closed metal container and disposed of correctly.
DO NOT exceed the rated capacity of the drill.
7
DO NOT operate the drill if any parts are missing as this may cause failure or possible personal
7
injury.
DO NOT leave the drill operating unattended.
7
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or
7
intoxicating medication.
DO NOT pull the cable from the power supply.
7
When not in use switch the drill off, remove plug from the power supply and do not leave
3
until the tool has come to a complete stop.
2. DESCRIPTION
The GDM bench and floor drills are suitable for light industrial, agricultural and woodworking
applications. The drills are fitted with flip-up safety guards and "No Volt Release" switches, which
prevent accidental restart after a mains power interruption. A rack and pinion feed shaft with preset
depth control for repetitive work is also included. All models have Morse Taper Spindles to
accept taper shank bits. M o r t i c e a t t a c h m e n t s and work clamps are also available for
these drills, contact your local Sealey dealer for information.
3. TECHNICAL SPECIFICATIONS
MODEL No:
Drilling Capacity (Chuck Size):
Spindle Nose Taper:
Swing:
Spindle centre to column:
Spindle travel:
Number of speeds:
Speed range:
Maximum Distance Spindle to Table:
Maximum Distance Spindle to Base:
Working Table Surface size:
Working Base Surface size:
Overall Base Size:
Column diameter:
Collar diameter:
Overall Height:
Motor Power:
Input Power:
Weight:
Optional Keyless Chuck 16mm:
4. CONTENT
4.1. Content
Check parts against the list below. If any items are damaged or missing contact your supplier.
3 Head Assembly
3 Chuck and Key
3 Column with Flange
3 Adjusting Handle with Set Screw (table)
3 Pivoted Clamp Bolts (2 - table arm & bracket)
3 Safety Guard
3 Set Screws (2)
3 Wedge
3 Arbor
GDM150B
GDM180B
16mm
20mm
MT2
MT3
436mm
520mm
178mm
220mm
80mm
80mm
16
16
120-3000rpm
120-3000rpm
480mm
495mm
670mm
685mm
Ø310mm
Ø355mm
205 x 205mm
245 x 240mm
440 x 260mm
520 x 320mm
80mm
80mm
60mm
75mm
1070mm
1085mm
450W - 230V
550W - 230V
650W - 230V
750W - 230V
68kg
80kg
GDMX/KC
GDMX/KC
3 Base
3 Table Arm, Bracket and Worm
3 Feed Handles and Knobs (3)
3 Table
3 Bolts and Washers (4)
3 Rack and Rack Ring
3 Screw (upper pulley cover)
3 Hex. Keys (2)
Original Language Version
GDM200F
16mm
MT2
436mm
178mm
80mm
16
120-3000rpm
800mm
1230mm
Ø310mm
205 x 205mm
460 x 275mm
80mm
60mm
1630mm
450W - 230V
650W - 230V
74kg
GDMX/KC
GDM150B, GDM180B, GDM200F
GDM150B
GDM180B
GDM200F
Issue: 4 - 08/03/12
Advertisement
