Advertisement
Table of Contents
Steel Induction Patio Heater
Item No.:50237
Model No.HYPH4601-12
Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Read the owner's manual thoroughly before installing or servicing this
result causing property damage, personal injury or loss of life.
Save these instructions for future use. If
you are assembling this unit for someone
else, give this manual to him or her and
read and save for the future.
Owner's Manual
DANGER
If you smell gas:
1. Shut off gas to the appliance.
3. If odor continues, keep away from
the appliance and immediately call
WARNING
Do not store or use gasoline or other
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
WARNING
For outdoor use only.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bond HYPH4601-12
Summary of Contents for Bond HYPH4601-12
- Page 1 Steel Induction Patio Heater Item No.:50237 Model No.HYPH4601-12 DANGER If you smell gas: 1. Shut off gas to the appliance. 3. If odor continues, keep away from the appliance and immediately call WARNING Do not store or use gasoline or other vicinity of this or any other appliance.
-
Page 2: Safety Information
Once you have a flame started, hold down the control knob for 1 minute. • Do not add water into the unit. • Do not operate unit if any part has been under water. Call a service technician to replace any Bond Manufacturing Company | Page 2... - Page 3 Bond Manufacturing Co. Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate the appliance. For assistance with repair or replacement of the burner or any other parts, calls Bond Manufacturing at 1.866.771.2663.
- Page 4 SUBJECT TO RADIANT HEAT AND COULD BE 91.44 cm 91.44 cm SERIOUSLY DAMAGED. Combustible materials should not be within 24 inches of the top of the unit, or within 36 inches around the entire unit. Bond Manufacturing Company | Page 4...
- Page 5 HARDWARE Item Description M5 x 12 Screw M6 x 12 Screw M8 x 16 Screw M6 Lock Nut Anchoring Nut Anchoring Arm Wrench Before beginning assembly of this product be sure all parts are present. Compare parts with package contents list and hardware contents list. If any part appears to be missing or damaged do not begin assembly of this product and call customer service immediately.
- Page 6 CONTENTS CONTENTS Item Description Upper Reflector Glass Tube Ring Burner Tank Housing Glass Tube Mesh Guard Body Supporter Battery (AA) Upper Supporter Wheel Assembly Bond Manufacturing Company | Page 6...
- Page 7 ASSEMBLY INSTRUCTIONS 1. Flip the tank housing (D) upside down and attach the wheel assembly (J) to the base of the tank housing (D) using 2 M8 x 16 screws (CC). 2. Attach the anchoring arms (FF) onto the base of the tank housing (D) using 6 silver M6 x 12 screws (BB) and 6 M6 nuts (DD).
- Page 8 (C). Attach the glass tube ring (B) to the top of the burner (C) using the 3 screws removed at the beginning of this step. Be sure to fully tighten. Bond Manufacturing Company | Page 8...
- Page 9 7. Place the glass tube (E) into the top of the glass tube ring (B). 8. Remove the 3 preassembled screws from the upper supporters (I). Place the upper reflector (A) onto the top of the upper supporters (I). Replace the 3 screws removed at the beginning of this step to secure the upper combination (A) to the upper supporters (I).
- Page 10 CYLINDER VALVE coupling nut clockwise. Make sure it is BLACK COUPLING NUT BLEED-OFF fastened securely and tighten connections turn clockwise to connect VALVE by hand only. turn clockwise REGULATOR to reseal Bond Manufacturing Company | Page 10...
-
Page 11: Operation
OPERATION • The glass tube may break if it is wet while in use; never use the heater while it’s raining outside. • Do not splash any liquid on the heater while it is in use. • Keep children away from the unit while in use; the glass tube may be extremely hot while in use. Do not touch. - Page 12 2. Turn the propane gas tank valve on the gas tank to close the gas supply and disconnect the propane gas tank WARNING: If the lighting instructions are not followed directly a fire or explosion may occur resulting in property damage, personal injury or death. Bond Manufacturing Company | Page 12...
-
Page 13: Maintenance
MAINTENANCE • Before performing any maintenance always disconnect propane gas tank. • Keep the heating item free and clear from combustible materials. • Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. • Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner is completely cooled down. -
Page 14: Warranty
• Use and installation other than what is listed in this manual. Please contact the manufacturer for replacement parts. CONTACT If you have any questions or concerns, please contact Bond Manufacturing Company at the below resources: Toll Free Phone 1-866-771-BOND (2663) | Monday - Friday, 8am - 4:30pm PST Email customer.service@bondmfg.com...
Need help?
Do you have a question about the HYPH4601-12 and is the answer not in the manual?
Questions and answers
how do I get a new igniter and thermel couple for my heater unit
how do i get a new igniter and thermal couple for my heater unit
You can obtain a new igniter and thermocouple for the Bond HYPH4601-12 heater unit by contacting Bond Manufacturing Company. You can reach them by calling their toll-free phone number 1-866-771-2663 (Monday - Friday, 8am - 4:30pm PST) or by emailing customer.service@bondmfg.com.
This answer is automatically generated
@Mr. Anderson
Thanks for the info, I will contact the Company. Would you happen to know how to replace the igniter and thermocoupling once received? The manual does not address this.
@Mr. Anderson Thanks for the info, I will contact the Company. Would you happen to know how to replace the igniter and thermocoupling once received? The manual does not address this.