EWM alpha Q 330 Progress puls HP MM TKM Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.3.6
5.3.7
5.3.8
5.3.9
5.3.10
5.3.11
5.3.12
5.3.13
5.3.14
5.4 TIG welding .................................................................................................................................. 77
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.5 MMA welding ................................................................................................................................ 84
5.5.1
5.5.2
5.5.3
5.6 Access control .............................................................................................................................. 88
5.7 Remote control ............................................................................................................................. 88
5.8 Power-saving mode (Standby) ..................................................................................................... 88
5.9 Interfaces for automation ............................................................................................................. 89
5.9.1
5.9.2
5.9.3
5.9.4
5.10 PC interface ................................................................................................................................. 91
5.11 Special parameters (advanced settings) ...................................................................................... 92
5.11.1
4
MIG/MAG operating point ............................................................................................. 46
5.3.6.1 Operating point setting via welding current, material thickness or wire
feed speed ..................................................................................................... 46
5.3.6.2 Arc length correction setting .......................................................................... 47
5.3.6.3 Accessory components for operating point setting ....................................... 47
5.3.6.4 coldArc / coldArc puls .................................................................................... 48
5.3.6.5 forceArc / forceArc puls ................................................................................. 49
5.3.6.6 rootArc/rootArc puls ....................................................................................... 50
5.3.6.7 pipeSolution ................................................................................................... 50
MIG/MAG functional sequences / operating modes ..................................................... 51
5.3.7.1 Explanation of signs and functions ................................................................ 51
MIG/MAG program sequence ("Program steps" mode) ............................................... 64
5.3.8.1 Selection of the program sequence parameter ............................................. 64
5.3.8.2 MIG/MAG overview of parameters ................................................................ 65
5.3.8.3 Example, tack welding (non-latched) ............................................................ 66
5.3.8.4 Example, aluminium tack welding (non-latched special) .............................. 66
5.3.8.5 Example, aluminium welding (latched special) ............................................. 67
5.3.8.6 Example, visible seams (latched super pulse) .............................................. 68
Conventional MIG/MAG Welding (GMAW non synergic) ............................................. 69
5.3.9.1 Setting the operating point (welding output).................................................. 69
Main program A mode .................................................................................................. 70
5.3.10.1 Selecting parameters (program A) ................................................................ 72
MIG/MAG automatic cut-out ......................................................................................... 72
Standard MIG/MAG torch ............................................................................................. 73
MIG/MAG special-torches............................................................................................. 73
5.3.13.1 Program and up/down operation ................................................................... 73
5.3.13.2 Switching between Push/Pull and intermediate drive ................................... 74
Expert menu (MIG/MAG) .............................................................................................. 75
5.3.14.1 Selection ........................................................................................................ 75
Welding torch and workpiece line connection .............................................................. 77
Welding task selection .................................................................................................. 78
5.4.2.1 Welding current setting .................................................................................. 78
TIG arc ignition ............................................................................................................. 79
5.4.3.1 Liftarc ............................................................................................................. 79
Function sequences/operating modes .......................................................................... 79
5.4.4.1 Explanation of signs and functions ................................................................ 79
5.4.4.2 TIG automatic cut-out .................................................................................... 82
TIG program sequence ("Program steps" mode) ......................................................... 83
Connecting the electrode holder and workpiece lead .................................................. 84
Welding task selection .................................................................................................. 85
5.5.2.1 Welding current setting .................................................................................. 85
5.5.2.2 Arcforce ......................................................................................................... 86
5.5.2.3 Hotstart .......................................................................................................... 86
5.5.2.4 Antistick ......................................................................................................... 86
Parameter overview ...................................................................................................... 87
Automation interface ..................................................................................................... 89
Remote control connection socket, 19-pole ................................................................. 90
RINT X12 robot interface .............................................................................................. 91
BUSINT X11 Industrial bus interface ............................................................................ 91
Selecting, changing and saving parameters................................................................. 92
5.11.1.1 Reset to factory settings ................................................................................ 94
5.11.1.2 Special parameters in detail .......................................................................... 95
099-005402-EW501
24.11.2016