Resetting Flow Limiting Device (Natural Gas) - Coleman Revolution Use & Care Manual

NATURAL GAS HOOK-UPS AND WARNINGS
FOR NATURAL GAS MODELS ONLY
All Coleman® Natural Gas Barbecues come equipped with a 10' Natural Gas hose with a quick connect socket
connection. This will allow you to attach your barbecue to your residential gas line.
To Connect
1. Push back the sleeve on the quick connect socket, insert the plug and release the sleeve.
2. Push the two pieces together until the sleeve snaps forward, to lock the plug in the socket.
To Disconnect
1. Push sleeve back and pull the plug out.
Testing For Gas Leaks
Before attempting to operate this barbecue:
• Always confirm that all burner control knobs are in the "OFF" position.
• Always connect the gas supply hose first, open lid and then open the gas shutoff valve.
Always use a brush or spray bottle to apply a 50/50 solution of liquid soap and water to all connection
o
points, to test for gas leaks. Never use a match or open flame
for that purpose.
Always look for bubbles to appear, as the appearance of
o
bubbles will indicate a gas leak.
Always turn off the gas immediately and tighten the
o
connection, if you find that a leak has been detected.
Before lighting the barbecue , always repeat this procedure
o
until no further gas leaks are found.
If a leak cannot be stopped, do not attempt to light the
o
barbecue. Always contact a certified Natural Gas technician
for assistance or the Coleman® Customer Care Agent 1-800-
275-4617.
NEW Natural Gas Barbecue
If you are experiencing poor natural gas barbecue performance,
including but not limited to low flame, low heat or poor heat
distribution, please review the following information:
• Always consult the Rating Label on the back of the barbecue to confirm that it has already been configured to
burn natural gas.
• If experiencing performance issues with a brand new barbecue hooked up to an older natural gas home
connection, it is possible that the natural gas supply line is not able to supply up to the essential 85,000 BTU's
required (depending on the model). Please contact Coleman® Customer Care for requirements and then
consult with your certified natural gas technician.
• All gas supply plumbing must be carried out by a qualified service agency. The Supply connection shall be
carried out in accordance with provincial authorities having jurisdiction, and in accordance with CAN/CGA
1-B149.1 & 2 installation code requirements.
• A shut off valve must be installed between the barbecue and the main supply. For natural gas, use a 3/8"
natural gas supply line capable of an input of up to 85,000 BTU's (depending on the model).
• When conducting pressure test always isolate the barbecue from the gas supply piping system by
disconnecting the barbecue and closing its individual manual shutoff valve. The gas supply piping system
should be tested at pressures which exceed 1/2 psi (3.5kPa).
• All gas supply plumbing must be able to supply 7" water column to the barbecue WITH ALL BURNERS IN
OPERATION.
Resetting Flow Limiting Device (Natural Gas Models)
If you are experiencing low heat performance issues, you may have activated the flow limiting feature in
your home's natural gas connection. To reset the flow limiting device, follow these steps:
1. Open barbecue lid.
2. Ensure that the control knobs are in the "OFF" position.
3. Ensure that the Natural Gas Supply valve is in the "OFF" position at the Home Connection.
4. Disconnect the Natural Gas Supply hose by separating the Quick Connect Assembly at the Home
connection.
5. Turn all control knobs to the "MAX" (
6. Reconnect the Natural Gas Supply hose by securing the Quick Connect assembly connection.
7. Using your hands only, check all connections to confirm that positive seal has been made.
8. Turn the knobs to the "OFF" position.
9. Slowly turn ON the Natural Gas Supply valve to the "ON" position.
10. Wait 30 seconds for the gas pressure to stabilize (60 seconds in cold weather).
11. Turn on the ignition burner control knob, to the "MAX" (
12. Press the electronic ignition button, or use the match and match holder to ignite the selected
burner (Barbecue lighter).
13. Repeat steps if not successful on first try.
) position.
) position and wait 3 to 5 seconds.
6
Natural gas hose
connection point
Natural Gas Home Supply /
Safety shut off valve
Natural Gas Hose
Quick Connector
Ensure that the Quick Connector is fully
connected to the natural gas hose
Side burner
valve gas jet