D-Link DVG-7111S User Manual

D-Link DVG-7111S User Manual

Voip telephone adapter
Hide thumbs Also See for DVG-7111S:

Advertisement

Quick Links

DVG-7111S
VoIP Telephone Adapter
User's Manual
Version 1.0
(21 Feb. 2014)

Advertisement

Table of Contents
loading

Summary of Contents for D-Link DVG-7111S

  • Page 1 DVG-7111S VoIP Telephone Adapter User’s Manual Version 1.0 (21 Feb. 2014)
  • Page 2 Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
  • Page 3: Table Of Contents

    Contents 1. Introduction ................................ 4 1-1 Product Overview ............................4 1-2 Hardware Description ..........................5 2. Getting Started ..............................7 3. VoIP TA Web Configuration ..........................14 3-1 SETUP ..............................17 3-1-1 Internet Setup ..........................17 3-1-2 VoIP Setup ............................. 21 3-1-3 LAN Settings ..........................
  • Page 4: Introduction

    VoIP TA allows you to use voice and fax services over IP in order to reduce the cost of all long distance calls. The DVG-7111S can be configured a fixed IP address or it can have one dynamically assigned by DHCP or PPPoE. It adopts either the G.711, G.726, G.729A or G.723.1 voice compression format to save network bandwidth while providing real-time, toll quality voice transmission and reception.
  • Page 5: Hardware Description

    Line Indicator: Line LED light on means FXO/PSTN line is in use (off-hook). Note: When starting up DVG-7111S, all indicators will light up. After about 40 seconds, the Reg. indicator will blink in green. If the Prov./Alm indicator continues to blink, it means DVG-7111S is currently communicating with ISP and has yet to obtain an IP address or fail to register to VoIP Service Provider.
  • Page 6 DVG-7111S User’s Manual Telephone Interface Description Rear Panel Line: Connect to your original telephone line on the wall jack with RJ-11 cable. Phone Port: Connect to your phones using standard phone cabling (RJ-11). WAN: Connect to your broadband modem using an Ethernet cable.
  • Page 7: Getting Started

    DVG-7111S User’s Manual SETUP 2. Getting Started To access the web-based configuration utility, open a web browser such as Internet Explorer and enter the IP address of the DVG-7111S. Open your Web browser and type http://192.168.8.254 into the URL address box.
  • Page 8 DVG-7111S User’s Manual SETUP Click Setup Wizard. Click Next D-Link Systems, Inc.
  • Page 9 DVG-7111S User’s Manual SETUP The username of ADMIN and USER have been defined and locked by default. It is highly recommended to create a login password to keep your router secure. Click Next. D-Link Systems, Inc.
  • Page 10 DVG-7111S User’s Manual SETUP Enter a NTP server or use the default server. Click Next. D-Link Systems, Inc.
  • Page 11 DVG-7111S User’s Manual SETUP Select your Internet connection type: DHCP – Most Cable ISPs or if you are connecting the DVG-7111S behind a router. Static IP – Select if your ISP supplied you with your IP settings. PPPoE – Most DSL ISPs.
  • Page 12 DVG-7111S User’s Manual SETUP Register to the SIP Proxy Server by clicking Enable support of SIP Proxy Server. Enter Proxy Server IP/Domain and Port. Outbound Proxy Support is optional. To register, please click on the Outbound Proxy Support box and enter Outbound Proxy IP/Domain and Port in it.
  • Page 13 DVG-7111S User’s Manual SETUP Setup is finished. Check the summary of your settings. To make new settings effective, you must click on the Restart button to reboot the DVG-7111S. Click Restart D-Link Systems, Inc.
  • Page 14: Voip Ta Web Configuration

    DVG-7111S User’s Manual SETUP 3. VoIP TA Web Configuration During configuration, please follow the Setup Hint for some specific procedure in case the VoIP TA fails to make the changes active. Situation 1: (example: Internet Setup) Setup Hint: Select DHCP WAN Setup.
  • Page 15 DVG-7111S User’s Manual SETUP Situation 2: (example: VoIP Service Provider) Setup Hint: Click “Edit” to start configuration. Click “Apply” after settings. Go to “MAINTAINACE”-> “Backup and Restore” save settings and reboot the system. D-Link Systems, Inc.
  • Page 16 DVG-7111S User’s Manual SETUP Situation 3: (example: Enable IP Filtering) Setup Hint: Click “Enable IP Filtering” check box to open the main screen. Click “Add” to enter an entry. After Adding an entry, you have to click “Apply”. Don’t forget to click “Apply” which in the filed of “Enable IP Filtering”.
  • Page 17: Setup

    DVG-7111S User’s Manual SETUP 3-1 SETUP 3-1-1 Internet Setup WAN (Wide Area Network) Settings are used to connect to your ISP (Internet Service Provider). The WAN settings are provided to you by your ISP and oftentimes referred to as "public settings". Please select the appropriate option for your specific ISP.
  • Page 18 DVG-7111S User’s Manual SETUP SETUP → Internet Setup SETUP → Internet Setup DHCP: Select this option if your ISP (Internet Service Provider) provides you an IP address automatically. Cable modem providers typically use dynamic assignment of IP Address. The Host Name field and Vendor Class ID are optional but may be required by some Internet Service Providers.
  • Page 19 DVG-7111S User’s Manual SETUP SETUP → Internet Setup PPPoE: Select this option if your ISP requires you to use a PPPoE (Point-to-Point Protocol over Ethernet) connection. Enter the PPPoE Account, PPPoE Password and re-enter Password to confirm. SETUP → Internet Setup PPTP: Point-to-Point Tunneling Protocol (PPTP) is a WAN connection.
  • Page 20 DVG-7111S User’s Manual SETUP SETUP → Internet Setup WAN Link Speed: Select WAN port link speed. SETUP → Internet Setup VoIP Connection Interface: Select a WAN interface for DVG-N5412SP VoIP traffic. SETUP → Internet Setup Factory Default MAC Address: The original MAC address of the VoIP Router.
  • Page 21: Voip Setup

    DVG-7111S User’s Manual SETUP VLAN is optional. It works with the Router or Switch that supports VLAN tag. By adding VLAN tag in packets may improve efficiency of voice traffic performance and security. Enable VLAN Tagging: It is to tag the packets for VLAN Router or Switch identifying.
  • Page 22 DVG-7111S User’s Manual SETUP SETUP → VoIP Setup Enable Support of SIP Proxy Server / Soft Switch: Check the box to register the VoIP TA with SIP proxy server or soft switch. ITSP Name: Enter the name of VoIP Service Provider.
  • Page 23 DVG-7111S User’s Manual SETUP SETUP → VoIP Setup Proxy Server IP/Domain: Enter the IP address or URL (Uniform Resource Locator) of SIP proxy server or soft switch. Proxy Server Port: Enter the SIP proxy server’s listening port for the SIP in this field. Leave this field to the default if your VoIP Service Provider did not give you a server port number for SIP.
  • Page 24 DVG-7111S User’s Manual SETUP Note: Proxy Server Realm, SIP Domain and Use Domain to Register are the parameters provided by VoIP Service Provider. If you fail to make a call, please contact your VoIP Service Provider. Bind Proxy Interval for NAT: Check the box to keep the binding exist by sending packets when the VoIP TA is behind a NAT and SIP proxy server is not able to keep the binding.
  • Page 25 DVG-7111S User’s Manual SETUP SETUP → VoIP Setup Outbound Proxy Support: Check the box to send all SIP packets to the destined outbound proxy server. An outbound proxy server handles SIP call signaling as a standard SIP proxy server would do.
  • Page 26 DVG-7111S User’s Manual SETUP For example (Example in Taiwan), If Server 1 is local VoIP Service Provider you can refer to Digit Map page for general settings. If Server 2 is global VoIP Service Provider (VoIP STUN, free to dial to some cities free charge) you can set individual dialing plan for VoIP STUN in Number Translation field.
  • Page 27: Lan Settings

    DVG-7111S User’s Manual SETUP 3-1-3 LAN Settings SETUP → LAN Setup Interface Mode: Select the VoIP TA serving as a Router with NAT or Bridge between WAN port and LAN port without NAT. Note: It is still accessible if LAN Interface Mode is Bridge.
  • Page 28 DVG-7111S User’s Manual SETUP Lease Time: Enter the length of time for the IP lease. Domain Name Server Assignment: Select Auto or Manual to get the IP address of Domain Name Server assigned by ISP or manually. Domain Name Server IP: Enter the primary and secondary IP address of Domain Name Server if Domain Name Server Assignment is Manual.
  • Page 29: Time And Date

    DVG-7111S User’s Manual SETUP 3-1-4 Time and Date SETUP → Time and Date Automatically synchronize with Internet time servers: The VoIP TA should automatically sync up with time servers. First NTP time server: Select the desired domain name of a NTP server as first priority.
  • Page 30: Advanced

    DVG-7111S User’s Manual ADVANCED 3-2 ADVANCED 3-2-1 VoIP 3-2-1-1 Caller Filter This function allows you to accept or reject any incoming call from the IP address listed in the filter rule. The call from the IP address of SIP proxy server is always accepted, despite Deny is selected or the IP address of SIP proxy server is not in the filter rule of Allow.
  • Page 31 DVG-7111S User’s Manual ADVANCED 3-2-1-2 Caller ID ADVANCED → VoIP → Caller ID FXS Caller ID Generation: Select DTMF, FSK or FSK+Type II Caller ID to enable the caller ID display function on FXS port. When enabled, the caller’s phone number will be displayed on your phone set when the call comes through.
  • Page 32 DVG-7111S User’s Manual ADVANCED Detection Level: Select the level for FXO detecting the caller ID. FSK Caller ID Type: Either Bellcore or ETSI can be selected. D-Link Systems, Inc.
  • Page 33 DVG-7111S User’s Manual ADVANCED 3-2-1-3 Calling Features ADVANCED → VoIP → Calling Features Do Not Disturb: Check the box to reject (busy tone played) incoming calls. Unconditional Forward: Check the box to forward incoming calls to the assigned “Forwarding Number” automatically. If configured forwarding to FXO it only makes FXO hook off, but not making FXO dial out.
  • Page 34 DVG-7111S User’s Manual ADVANCED ADVANCED → VoIP → Calling Features Enable Call Feature Code: Check the box to enable/disable some call feature codes through a phone set. Call pickup: Allow one to pick up someone else’s telephone call. Call Back on Busy: Your phone will ring back the last number that called you.
  • Page 35 DVG-7111S User’s Manual ADVANCED Calling Feature Instructions: Call Hold: The call will be held after the FLASH button is pressed on the phone set. The VoIP TA will play a hold music (provided by your VoIP Service Provider) to the remote end.
  • Page 36 DVG-7111S User’s Manual ADVANCED 3-2-1-4 Codec ADVANCED → VoIP → Codec Preferred Codec Type: Select a preferred codec type for all calls. Since different voice codecs have different compression ratios, the sound quality and occupied bandwidths are also different. The factual codec may determine by the called party.
  • Page 37 DVG-7111S User’s Manual ADVANCED Packet Interval: Select the frame size of voice package from different codec. It defines the time interval for the VoIP TA to send a RTP packet or voice packet to the receiving side. The smaller the value, the greater the bandwidth takes, and larger values might cause voice delay.
  • Page 38 DVG-7111S User’s Manual ADVANCED ADVANCED → VoIP → CPT / Cadence CPT # 1: Define the call process tones for the VoIP TA generates. ADVANCED → VoIP → CPT / Cadence FXS Ring Cadence Settings: Specify the ring cadence for the FXS port. In this field, you specify the on and off pulses for the ring.
  • Page 39 DVG-7111S User’s Manual ADVANCED 3-2-1-6 Digit Map Digit Map supports multiple dial plans which help users to arrange least cost route. Each Proxy Server has individual dial plan which combines the original feature of Digit Map and Speed Dial. You can use “?”...
  • Page 40 DVG-7111S User’s Manual ADVANCED ADVANCED → VoIP → Digit Map → VoIP Route Profile There are 10 VoIP route profiles. Each VoIP route profile provides four routes to select. Server 1, Server 2, Server 3, Phone Book and None can be selected for each route.
  • Page 41 DVG-7111S User’s Manual ADVANCED Digit Map Table appears like: As you dial the phone numbers starting with 09, like 0912345678, the call will only go through Server 1 (local VSP). If Sever1 is failed, the call will be diverted to PSTN.
  • Page 42 DVG-7111S User’s Manual ADVANCED Digit Map Table appears like: As you dial the phone numbers staring with 03, like 0312345678, the number will be changed to 0045312345678, followed the number translation of Server 2, and the call will go through Server 2 (free VSP) at first.
  • Page 43 DVG-7111S User’s Manual ADVANCED Example 3 – Multiple Route, The number translation of Server 1 is blank, and the number translation of Server 2 appears like: The number translation of Server 3 appears like: The VoIP Route Profile appears like:...
  • Page 44 DVG-7111S User’s Manual ADVANCED Digit Map Table appears like: As you dial the phone numbers staring with 00244, like 00244123456789, the number will be changed to 0123456789 followed the number translation of Server3, and the call will go through Server 3 (UK VSP) at the first.
  • Page 45 DVG-7111S User’s Manual ADVANCED For example, Scan Code: 091 VoIP Dial-out: 0912345678 PSTN Dial-out: leave it as blank User Dial Length: 2 Route: Auto VoIP Route Profile: Route # 1 Pick up the handset and dial 091, and the system will do the things as follow: 1.
  • Page 46 DVG-7111S User’s Manual ADVANCED For example, Scan Code: 4% VoIP Dial-out: 00244% PSTN Dial-out: leave it as blank User Dial Length: 11 Route: Auto VoIP Route Profile: Route # 3 Pick up the handset and dial 4323456789. The system will do the things as follow: 1.
  • Page 47 DVG-7111S User’s Manual ADVANCED Method 3- Substitution: It helps you dial to destination that you can not dial by phone. Destination like: anny@sip.com.uk. Fill the number into the Scan Code column and enter the desired name into the VoIP Dial-out column.
  • Page 48 DVG-7111S User’s Manual ADVANCED 3-2-1-7 DTMF & PULSE ADVANCED → VoIP → DTMF & PULSE Dial Wait Timeout: Enter the timeout duration after the user picks up the phone set. Inter Digits Timeout: Enter the timeout duration between the intervals of each key pressed. When exceeding the set timeout duration without entering further digits, the numbers entered will be dialed out.
  • Page 49 DVG-7111S User’s Manual ADVANCED Info. Note: Out-of-Band DTMF transport method varies from VoIP networks, please contact your VoIP provider for the preferred method. FXS Pulse Detection: It allows FXS detect PULSE dial method sends from a phone set. Enable Hook Flash Event: Select Auto, RFC2833, or SIP info for the signaling method of Hook Flash Event.
  • Page 50 DVG-7111S User’s Manual ADVANCED ADVANCED → VoIP → FAX Switch FAX On CED Detection: DVG will send FAX Re-Invite immediately as it detect FAX CED tone, that will save handshaking time between FAX machines. Restrict T.38: DVG will reject T.38 Re-invite in case the FAX type contains without T.38.
  • Page 51 DVG-7111S User’s Manual ADVANCED 3-2-1-9 Hot Line ADVANCED → VoIP → Hot Line Hot Line: Check to direct the call automatically to a pre-configured destination without any action when the FXS is off-hook. (ie. as the user picks up the phone). When the FXS is under Hot Line mode, no other phone numbers can be dialed.
  • Page 52 DVG-7111S User’s Manual ADVANCED FXO Line VoIP call in options: Set FXO dial-out mode when the VoIP call indicates the FXO extension number. Caller Indicate Dial-Out: When someone makes a call to this FXO port from Internet, it will dial to PSTN with the number assigned in SIP packet.
  • Page 53 DVG-7111S User’s Manual ADVANCED 3-2-1-10 Line ADVANCED → VoIP → Line Enable: Tick the check box to enable a line. If some lines are not used, disable them (Pause Function) to avoid unnecessary waiting when an incoming call is diverting to the line.
  • Page 54 DVG-7111S User’s Manual ADVANCED Flash Time: Set the time frame that FXO generates a FLASH signal. Enable Polarity Reversal: This option forces VoIP TA to detect the reversal of polarity on FXO port as the primary signal to drop a call. Some telephone switches or PBX reverse the line polarity to inform the remote end to drop an ongoing call.
  • Page 55 DVG-7111S User’s Manual ADVANCED ADVANCED → VoIP → Line Ring (Early Media) Time Limit[10 - 600secs]: Enter the timeout to cancel a call if no one answers the phone. Enable End of Digit Tone: Check the box to activate the function of playing a “Beep-Beep” tone to notify the user that the call is in progress.
  • Page 56 DVG-7111S User’s Manual ADVANCED ROH Duration: It is the maximum time for FXS play ROH, then FXS will stop play ROH and keep silence. FXS Ring Voltage: It is to set the Ring Voltage of FXS. FXS Ring Frequency : It is to set the Ring Frequency of FXS.
  • Page 57 DVG-7111S User’s Manual ADVANCED 3-2-1-11 Phone Book Phone Book: It is used for peer-to-peer communication. Some peer information needs to be added to this section prior to making peer-to-peer calls. You need to enter the phone number and the IP address of the remote peer.
  • Page 58 9002 and 9003, and so forth. SIP Transport Protocol: DVG-7111S supports UDP and TCP for SIP signaling. Most of SIP Server support UDP, if you prefer TCP please make sure whether remote party supports TCP or not.
  • Page 59 DVG-7111S User’s Manual ADVANCED ADVANCED → VoIP → SIP Advanced Session Expiration: This field will set the time that the VoIP TA will allow a SIP session to remain die (without traffic) before dropping it. Session Refresh Request: Select UPDATE or re-INVITE to send refresh requests to the Server.
  • Page 60 DVG-7111S User’s Manual ADVANCED ADVANCED → VoIP → SIP Advanced Anonymous Caller ID (CLIR): Check the box to lock the delivery of the Caller ID to the called party. CLIR At Transit In W/O Caller ID: Check the box to use “anonymous” as Caller ID for PSTN incoming calls when the Caller ID of PSTN incoming call is not detected.
  • Page 61 INVITE. Different format of INVITE header might cause the call not to be connected. Please consult with your VoIP Service Provider before enabling it. Callee Quick Media: DVG-7111S will send RTP to remote party immediately as user answer an inbound call.
  • Page 62 DVG-7111S User’s Manual ADVANCED 3-2-1-13 PSTN Control ADVANCED → VoIP → PSTN Control Trunk Dial Out Verify/ Trunk Dial Out Replace: VoIP TA will check (verify) the dial out prefix from dial out numbers and change (replace) the prefix to transit out through FXO port.
  • Page 63: Access Control

    DVG-7111S User’s Manual ADVANCED 3-2-2 Access Control 3-2-2-1 MAC Filtering Use MAC Filters to deny computers within the local area network from accessing the Internet. You can either manually add a MAC address that are connected to the VoIP TA.
  • Page 64: Firewall And Dmz

    DVG-7111S User’s Manual ADVANCED 3-2-3 Firewall and DMZ 3-2-3-1 DMZ DMZ (Demilitarized Zone) allows the server on the LAN site to be directly exposed to the Internet for accessing data and to forward all incoming ports to the DMZ Host. Adding a client to the DMZ may expose that computer to a variety of security risks;...
  • Page 65 DVG-7111S User’s Manual ADVANCED 3-2-3-2 DoS Prevention ADVANCED → Firewall and DMZ → DoS Prevention Enable DoS Prevention: Check the box to prevent DoS attacks from WAN or LAN. There are various types of DoS attacking. Leave settings in this field to the default if you are not familiar with it.
  • Page 66 DVG-7111S User’s Manual ADVANCED 3-2-3-3 IP Filtering Use IP Filters to deny particular LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for a specific IP address. The screen will display well-known ports that are defined.
  • Page 67 DVG-7111S User’s Manual ADVANCED 3-2-3-4 Port Filtering Port filtering enables you to control all data that can be transmitted over routers. When the port used at the source end is within the defined scope, it will be filtered without transmission.
  • Page 68 DVG-7111S User’s Manual ADVANCED 3-2-3-5 Virtual Server Enable users on Internet to access the WWW, FTP and other services from your NAT. It is also known as port forwarding. When remote users are accessing Web or FTP servers through WAN IP address, it will be routed to the server with LAN IP address.
  • Page 69: Advanced Network

    DVG-7111S User’s Manual ADVANCED 3-2-4 Advanced Network 3-2-4-1 QOS WAN QoS ADVANCED → Advanced Network → QoS Enable WAN QoS: Check the box to guaranty the voice quality. The system reserves the bandwidth for voice packets, and the data transmission is distributed to less bandwidth.
  • Page 70 DVG-7111S User’s Manual MAINTENANCE 3-2-4-2 NAT Traversal If your VoIP TA is set up behind an Internet sharing device, you can select either the NAT or STUN protocol. ADVANCED → Advanced Network → NAT Traversal Enable NAT Public IP: Check the box to use the IP address of the Internet sharing device if the VoIP TA is set up behind an Internet sharing device.
  • Page 71 DVG-7111S User’s Manual MAINTENANCE 3-2-4-3 STUN Inquiry Use “STUN Inquiry” to detect your IP sharing device’s NAT type and communication between a STUN server and client. ADVANCED → Advanced Network → STUN Inquiry NAT Type: It shows the NAT type of your router.
  • Page 72 DVG-7111S User’s Manual MAINTENANCE 3-2-4-5 UPnP ADVANCED → Advanced Network → UPnP Enable UPnP: Check the box to enable the VoIP TA’s IP traffic to pass through an Internet sharing device. This function only works when the Internet sharing device supports UPnP and has it enabled.
  • Page 73: Maintenance

    DVG-7111S User’s Manual MAINTENANCE 3-3 MAINTENANCE 3-3-1 Device Management MAINTENANCE → Device Management Note: There are two operating levels when entering the Web UI. Logging-in as the ADMIN allows you to change all settings. A Web UI USER only has access to some settings.
  • Page 74: Backup And Restore

    DVG-7111S User’s Manual MAINTENANCE 3-3-2 Backup and Restore Save and Reboot MAINTENANCE → Backup and Restore Save All Settings: Click the Save All Settings check box and reboot the system after completing changes. The new settings will take effect after the VoIP TA is restarted.
  • Page 75 DVG-7111S User’s Manual MAINTENANCE Update Settings MAINTENANCE → Backup and Restore To restore a system settings file, click on Browse to search the local hard drive for the file to be used. Once you locate the file, click Upload Settings to overwrite the current settings with the settings saved to the file.
  • Page 76: Firmware Update

    DVG-7111S User’s Manual MAINTENANCE 3-3-3 Firmware Update The VoIP TA supports a software upgrade function from a remote server. Please consult your VoIP Service Provider for information about the following details. MAINTENANCE → Firmware Update Upgrade Server: Select the upgrade type: TFTP, FTP, or HTTP.
  • Page 77: Dynamic Dns

    DVG-7111S User’s Manual MAINTENANCE 3-3-4 Dynamic DNS ADVANCED → Dynamic DNS Enable Dynamic DNS: Check the box to enable DDNS function. It is only necessary when the VoIP TA is set up behind an Internet sharing device that uses a dynamic IP address and does not support DDNS.
  • Page 78: Log Settings

    DVG-7111S User’s Manual MAINTENANCE 3-3-5 Log Settings MAINTENANCE → Log Settings Enable: Check the box to send event notification messages across IP networks to the Server. Server Address: Enter the System Log Server’s IP address. Port: Enter the System Log Server’s listening port. Leave this field to the default if your VoIP Service Provider did not provide you a server port number for System Log Server.
  • Page 79: Diagnostics

    DVG-7111S User’s Manual MAINTENANCE 3-3-6 Diagnostics Use “Ping” to verify if a remote peer is reachable. Enter a remote IP address and click “Test” to ping the remote host. The result would be shown on Result Table MAINTENANCE → Diagnostics...
  • Page 80: Provision

    DVG-7111S User’s Manual MAINTENANCE 3-3-7 Provision Provisioning is a function that automatically updates your VoIP TA’s configuration by using a TFTP, FTP, or HTTP server located on the Internet. If you have access to such service, you will need to know the URL or IP address of the Provisioning Server.
  • Page 81: Cdr

    DVG-7111S User’s Manual MAINTENANCE 3-3-8 CDR The user can set up a CDR Server to record call details for every phone call with TCP protocol. The present CDR provides the call event such as HOOK ON, HOOK OFF, DIALED NUMBER, DATE…recording in a text file and which can be imported to prepare an analysis report.
  • Page 82: Status

    DVG-7111S User’s Manual STATUS 3-4 STATUS 3-4-1 Device Info STATUS → Device Info For System Information, it shows Model Name, Time and Date and Firmware Version. For WAN Port Information, it shows IP address, subnet mask, default gateway and DNS server. If you use PPPoE to obtain IP, you will know if the IP is obtained through this method.
  • Page 83: Voip Status

    DVG-7111S User’s Manual STATUS STATUS → Device Info For DHCP Server, it shows DHCP is enabled or not, IP Pool Range, Lease Time and DNS. For Hardware, it shows the hardware platform and driver version. 3-4-2 VoIP Status STATUS → VoIP Status For Port Status, it includes if each port registers to Proxy successfully, the last dialed number, how many calls each port has made since the VoIP TA is start, etc.
  • Page 84: Lan Client

    DVG-7111S User’s Manual STATUS 3-4-3 LAN Client The DHCP Clients table displayed LAN device that has already been assigned an address from DVG-7111S. You can check if the DHCP client has obtain an IP address. STATUS → LAN Client D-Link Systems, Inc.
  • Page 85: Statistics

    DVG-7111S User’s Manual STATUS 3-4-4 Statistics STATUS → Statistics Display the information of the last call made. Press Refresh button to get the latest RTP Packet Summary. 3-4-5 Logout If setting or parameter has been changed, remember to save the changes before you logout the configuration menu.
  • Page 86: Configuring The Voip Ta Through Ivr

    DVG-7111S User’s Manual VoIP Router Configuration-IVR 4. Configuring the VoIP TA through IVR VoIP transmits voice data (packets) via the Internet, hence the condition and status of the network environment is relatively important to the telecommunications quality. If any one of the parties involved in VoIP communications has insufficient bandwidth or frequent packet loss, the telecommunication quality will be poor.
  • Page 87: Ivr Functions Table

    DVG-7111S User’s Manual VoIP Router Configuration-IVR a new IP address) enter 192*168*1*2 (new IP address). Save Settings When all setting procedures are completed, dial 509 (Save Settings) from phone keypad. Wait for about three seconds, you should hear a voice prompt “1 (one).” You can now hang up the phone and please reboot the VoIP TA to enable the new settings.
  • Page 88: Ip Configuration Settings-Set The Ip Configuration Of The Wan Port

    DVG-7111S User’s Manual VoIP Router Configuration-IVR 4-2 IP Configuration Settings—Set the IP Configuration of the WAN Port Static IP Settings Note: Complete static IP settings should include a static IP (option 1 under 114), IP address (111), Subnet Mask (112), and Default Gateway (113). Please contact your Internet Service Provider (ISP) if you have any question.
  • Page 89 DVG-7111S User’s Manual VoIP Router Configuration-IVR Select a PPPoE After entering IVR mode, dial 114. When voice prompt plays “Enter value,” dial 3 (to select PPPoE). PPPoE Account Settings After entering IVR mode, dial 121. When voice prompt plays “Enter value”, enter the account number followed by”#”.
  • Page 90: Pppoe Character Conversion Table

    (high-lighted) of each pair of the column (“Input Key”) represents the codes to be entered for the corresponding numbers, alphabets or symbols. For example, to enter “D-Link” according to the table below, enter: 148322495451 Numbers...
  • Page 91: Dialing Principles

    DVG-7111S User’s Manual Appendix 5. Dialing Principles 5-1 Dialing Options Dial the phone number which you want to call and press # to call out immediately. Note that if the “# (pound)” not dialed, the number will be called out after 4 seconds by default. The period between number dialed and call out is named “Inter Digits Timeout”.
  • Page 92: Routing

    DVG-7111S User’s Manual Appendix 5-3 Routing To achieve maximum flexibility, the number dialed will be looked up in several tables defined by VoIP TA. If no match is found from Digit Map Table, it will then look up the number from another table and to the registered VoIP Service Provdier.
  • Page 93 DVG-7111S User’s Manual Appendix Start Enter a phone number (D#) Is (D#) defined Change the number to in Digit Map Global Number. table? Is (D#) or Global Number defined in Phone Book table? Is (D#) or Global Number defined in Server 1?
  • Page 94: Appendix

    DVG-7111S User’s Manual Appendix Appendix Product Features  One 10/100Mbps auto-negotiation, auto-crossover RJ-45 Ethernet port  Support static IP, PPPoE and DHCP address assignment and dynamic DNS (DDNS)  QoS: IP TOS (Type of Services) and DiffServ (Differentiated Services) for both SIP signaling and RTP ...
  • Page 95 DVG-7111S User’s Manual Appendix Registration status Ping tests STUN/UPnP status Hardware / software information  Firmware Upgrade through HTTP, TFTP, FTP and proprietary image server  Configuration Backup/Restore  Reset button (with restore factory default function)  Front Panel LED : voice ports, WAN, LAN, Register, Power, Alarm ...

Table of Contents