Megapix LPR DWC-MB45iALPRT Quick Start Manual

Quick Start Guide
Outdoor Camera Waterproof Outdoor Camera Waterproof
Installation Guide Installation Guide
DWC-MB45iALPRT
Attach additional moisture absorbers(card type) Attach additional moisture absorbers(card type)
Attach accessory moisture absorbers (card type)and close the cover. Attach accessory moisture absorbers (card type)and close the cover.
The accessory moisture absorber is provided in a sealed package. The accessory moisture absorber is provided in a sealed package.
It can be used to prevent the moisture(dew formation) that can occur as a result of water It can be used to prevent the moisture(dew formation) that can occur as a result of water
entering the set during the product installation procedure(cover separation). entering the set during the product installation procedure(cover separation).
1. Remove the packaging for the moisture absorber provided as an accessory. 1. Remove the packaging for the moisture absorber provided as an accessory.
2. Assemble the front cover with moisture absorber into the body. 2. Assemble the front cover with moisture absorber into the body.
Default Login Information: admin | admin
3. How to attach the absorber(s). 3. How to attach the absorber(s).
When logging into the camera for the first time, you will be prompted
to set up a new password. You can set the new password using the
: Refer to the picture at the bottom. : Refer to the picture at the bottom.
DW® IP Finder™ software or directly from the camera's browser menu.
Do not install it in a humid environment. Do not install it in a humid environment.
WHAT'S IN THE BOX
(Dome moisture or dew formation can be caused.) (Dome moisture or dew formation can be caused.)
Screws and
Quick Setup and
1 Plastic Anchors Do not leave it without the cover for more than 10 minutes. Do not leave it without the cover for more than 10 minutes.
Installation Guide
– 4pcs
If the package is removed from the accessory moisture absorber, If the package is removed from the accessory moisture absorber,
Mounting
1 Star Wrench
Template
- do not get close to water. - do not get close to water.
Waterproof Cap
The whole process of [Cover Seperation - Attach Moisture Absorber - Close Cover] The whole process of [Cover Seperation - Attach Moisture Absorber - Close Cover]
Test Video Cable 1
and Gasket
Moisture
Absorber
1 set
and Guide
(Recommended)
NOTE:
Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
'Search by Product' search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click 'Search'. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual for
Absorber attachment point Absorber attachment point
complete and proper installation and usage.
Tel: +1 (866) 446-3595 / (813) 888-9555
digital-watchdog.com
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
STEP 1 – PREPARING TO MOUNT THE CAMERA
1. The mounting surface must bear five times the weight of
your camera.
2. Do not let the cables get caught in improper places or the electric line
cover to be damaged. This may cause a breakdown or fire.
3. CAUTION: These servicing instructions are for use by qualified service
personnel only. To reduce the risk of electric shock do not perform any
servicing other than that contained in the operating instructions unless
you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply
Unit marked "Class 2" or "LPS" or "PS2" and rated 12 Vdc, 0.75A min.
Outdoor Camera Waterproof
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with the Installation Guide
output evaluated as a Limited Power Source as defined in UL60950-1
or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as defined
Attach additional moisture absorbers(card type)
in IEC TR 62102. As such, associated Ethernet wiring shall be limited to
Attach accessory moisture absorbers (card type)and close the cover.
inside the building.
The accessory moisture absorber is provided in a sealed package.
7. Install the moisture packet in the base of the camera's lens.
It can be used to prevent the moisture(dew formation) that can occur as a result of water
a. Remove the moisture absorber from the packaging.
entering the set during the product installation procedure(cover separation).
b. Cut the card and folder along the dotted line.
1. Remove the packaging for the moisture absorber provided as an accessory.
c. Place the moisture absorber behind the camera's lens module. See
2. Assemble the front cover with moisture absorber into the body.
1 set
drawing for more information.
3. How to attach the absorber(s).
NOTE: The camera will generate enough heat to dry moisture
: Refer to the picture at the bottom.
during operation. In most cases it will not need the
1
moisture absorber for more than the first day. In cases
where the camera can experience a moisture issue,
users must keep the moisture absorber in the camera.
1 set The moisture absorber has an approximately 6-month
life cycle, varying depending on the environment.
WARNING: It is highly recommended that you install the moisture
absorber when mounting the camera. The moisture
absorber prevents moisture from being captured
inside the camera's housing, which may cause image
performance issues and damage the camera.
Please cut the absorber along the Please cut the card type absorber along Please cut the card type absorber along
dotted line, overlap and attach them
a dotted line, overlap and attach them a dotted line, overlap and attach them
according to the direction of the arrow.
according to the direction of the arrow. according to the direction of the arrow.
8. Using the mounting template sheet or the camera itself, mark and
drill the necessary holes in the wall or ceiling.
STEP 2 – POWERING THE CAMERA
Pass the wires through and make all the necessary connections. See STEP 4.
1. When using a PoE Switch or PoE Injector, connect the camera using an
Ethernet cable for both data and power.
2. When not using a PoE Switch or PoE Injector, connect the camera to the
switch using an Ethernet cable for data transmission and use a power
adapter to power the camera.
STEP 3 – INSTALLING THE CAMERA
1. Once all cables are connected, secure the camera
to the mounting surface using the included screws.
2. To use the camera's waterproof wiring:
a. Install the LAN cable into
b. will be assembled to
b
c. Thread tightly to
c
NOTE: To ensure moisture seal, make sure the o-ring is in place
between
a
outdoor rated sealer is recommended.
NOTE: When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
3. Loosen the pan and tilt screws at the base of the camera's bracket to
adjust the camera's view and position.
Resetting the camera: To reset the camera, use the tip of a
paper clip or a pencil and press the reset button. Pressing the
Do not install it in a humid environment.
button for five (5) seconds will initiate a camera-wide reset of
(Dome moisture or dew formation can be caused.)
all the settings, including network settings.
Do not leave it without the cover for more than 10 minutes.
If the package is removed from the accessory moisture absorber,
LPR INSTALLATION GUIDELINES
- do not get close to water.
• The LPR camera should be mounted at a height between 3~8 ft., and
The whole process of [Cover Seperation - Attach Moisture Absorber - Close Cover]
a distance no greater than 80 ft. from the target area. Exceeding
the distance recommendations may result in a poor quality image
of moving license plates.
• Ensure that the camera angle is no more than 20° degrees
(horizontally) 30° degrees (vertically) from the target area.
• It is recommended to position a license plate or vehicle to reflect
the IR light of the camera while adjusting the camera's focus of the
target area.
• After mounting the camera, you can press the Zoom Lens Button
(located on the underside of the camera) to sequentially zoom and
Please cut the card type absorber along
a dotted line, overlap and attach them auto-focus the camera. Alternatively, the camera's web GUI or
according to the direction of the arrow. management software can be utilized as well. The longer the Zoom
Lens button (T-W jog button) is pressed down, the further the lens
Absorber attachment point
module will zoom.
• Please note that the cameras ship with focus in Manual mode. To
change the camera's focus to Auto, enter the camera's web GUI and
use the +/- zoom buttons on the left of the camera image.
c
b
a
.
a
with a 1/4 turn.
a
.
b
and . In extreme environments use of an
b
Quick Start Guide
Power requirements Power consumption
DC12V, PoE
DC12V Max 9W
(IEEE 802.3af class 3).
PoE Max 10.5W
Adapter not Included.
Reset button
SD card
input
Zoom lens
button
Test video
output
THE CAPTURED IMAGE SHOULD BE FILLED WITH THE FULL WIDTH OF THE VEHICLES
THE CAMERA SHOULD BE MOUNTED AT AN ANGLE NO GREATER THAN 30 DEGREES
>11.5ft
< 30°
CAMERA ANGLE NO GREATER THAN 20 DEGREES FOR SIDE MOUNT INSTALLATIONS
< 20°