Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for extronics iTAG X30
Summary of Contents for extronics iTAG X30
- Page 1 Operating Manual iTAG X30...
- Page 2 (See DDM for the latest Version) For warranty information, refer to Terms and Conditions at http://www.extronics.com ©2020 Extronics Limited. This document is Copyright Extronics limited. Extronics reserve the right to change this manual and its contents without notice, the latest version applies.
-
Page 3: Table Of Contents
Tag usage instructions ..................9 Before using the tag ..................9 Configuring and updating the tags ..............9 4.2.1 Activating the iTAG X30 ................ 11 To Activate a tag:....................11 To activate multiple tags: ................... 12 4.2.2 How to Configure .................. 13 4.2.3... - Page 4 EU Declaration of Conformity ..............21 Manufacturer ..................... 24 Radio Equipment – FCC Warning Statement ............ 25...
-
Page 5: Introduction
The iTAG X30 worker location tag with hybrid technology, allows for accurately locating workers in Hazardous and Non-Hazardous areas, anytime anywhere. The iTAG X30 tag provides, audible, visual and tactile alerts and works with Stanley healthcare MobileView software to provide real-time alerting and reporting, for worker location solutions. -
Page 6: Safety Information
Warning! The iTAG X30 should only be cleaned with a damp cloth. Warning! Do not open the iTAG X30. There are no user-serviceable parts inside. Warning! Any repairs or replacement of parts MUST be performed by the manufacturer or its nominated sub-contractor or agent. -
Page 7: Marking Information
2.3 Marking Information Where: • YYYY is the Notified Body for production • XXXXXX: is the serial number • ZZZZ is a code to identify model variants Exact layout of markings may differ from that shown. -
Page 8: Tag Features
3 Tag Features Emergency Call Button The iTAG X30 features a call button which can be activated in the case of an emergency, which triggers an event in MobileView to show the location of the worker in need of assistance. -
Page 9: Mounting
Mounting The iTAG X30 comes complete with a stainless-steel clip which can be used to clip to PPE or used with a lanyard. Simple configuration The iTAG X30 Firmware contains 7 pre-defined configurations, which can be activated quickly and easily using the TED and Tag Manager BD. - Page 10 Click detect:...
-
Page 11: Activating The Itag X30
4.2.2 Activating the iTAG X30 On delivery from the factory, tags must be activated before configuring and use. A single tag or multiple tags can be activated simultaneously. To Activate a tag: Confirm the tag is detected. See Detecting Tags... -
Page 12: To Activate Multiple Tags
• From the Detected Tags list, right click on the tag and select Activate. The tag colour indicator changes to green (Activated Tag). The tag LED will flash to indicate communication. • To activate multiple tags: Confirm the tags are detected. See Detected Tags 1. -
Page 13: How To Configure
4. Click Finish. 4.2.3 How to Configure The iTAG X30 must be initially configured using the TMBD application (Tag manager BD application, which is part of the Hardware manager application) The TMBD application allows you to activate and configure the following tag parameters according to sites infrastructure and use case. - Page 14 WPA-PSK:...
-
Page 15: Available Configurations
4.2.4 Available configurations The tag firmware contains 7 pre-defined configurations. These configurations define the tag type and beacon rate behaviour. Each configuration has a unique ID number called a “Static Configuration” which cannot be edited. Only 1 configuration can be selected and used per tag. -
Page 16: Setting The Configuration
If a new version of tag firmware is available, you will be notified. 4.3 LED and Audio Indications The iTAG X30 has multi-colour LED’s on the top of the tag and on the front of the tag, Green Flashing – Tag is active... -
Page 17: Mounting The Tag
*Battery life depends on configuration and use case. 4.5.1 Battery levels and charging The iTAG X30 has the following 3 battery levels that are shown in MobileView: • High – Indicate the tag has more than 75% • Medium – Indicates the tag has between 75% and 30% •... -
Page 18: Battery Capacity
C. When connecting to a USB power supply, ensure the supply is rated less than 100W. 4.6 Transport All iTAG X30 devices must be transported and stored such that they are not subjected to any excessive mechanical or temperature stresses. -
Page 19: Authorized Persons
4.7 Authorized Persons Only persons trained for the purpose are authorized to handle the iTAG X30; they must be familiar with the unit and must be aware of the regulation and provisions required for explosion protection as well as the relevant accident prevention regulations. -
Page 20: Variants
X124873 iTAG X30 Protective cover for call button Pack of 50 X124874 PVC Kiss Cut Blank Photo ID Card for iTAG X30 Pack of 10 X124876 PVC Kiss Cut Blank Photo ID Card for iTAG X30 Pack of 50 X124875... - Page 21 5.1 EU Declaration of Conformity...
- Page 24 6 Manufacturer The iTAG X30 is manufactured by: Extronics Ltd, 1 Dalton Way, Midpoint 18, Middlewich Cheshire CW10 0HU Tel. +44(0)845 2775000 Fax. +44(0)845 2774000 E-mail: info@extronics.com Web: www.extronics.com Under licence by: Omni-ID Inc. 333 West Commercial Street Suite 333 – 1500 East Rochester N.Y.
- Page 25 7 Radio Equipment – FCC and ISED Warning Statement FCC & ISED Warning statement: This device complies with Industry Canada’s licence-exempt RSSs and Part 15 of the FCC Rules. • Operation is subject to the following two conditions: o This device may not cause interference; and o This device must accept any interference, including interference that may cause undesired operation of the device.
Need help?
Do you have a question about the iTAG X30 and is the answer not in the manual?
Questions and answers