Campbell AGPS Base Station Installation Manual
  1. Manuals
  2. Brands
  3. Campbell Manuals
  4. Safety Equipment
  5. AGPS Base Station
  6. Installation manual

Campbell AGPS Base Station Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Advisor Guide Pedestrian Signal
(AGPS) Installation Manual
906-0003
Revision D ● January 20, 2014
This Installation Guide provides guidance to those involved in the installation of the application.
This guide assumes that you have some knowledge of the [operating system] and the [system].

Advertisement

Table of Contents
loading

Related Manuals for Campbell AGPS Base Station

Summary of Contents for Campbell AGPS Base Station

  • Page 1 Advisor Guide Pedestrian Signal (AGPS) Installation Manual 906-0003 Revision D ● January 20, 2014 This Installation Guide provides guidance to those involved in the installation of the application. This guide assumes that you have some knowledge of the [operating system] and the [system].
  • Page 2 Campbell Company. The information furnished herein is believed to be accurate and reliable. However, no responsibility is assumed by Campbell Company for its use, or for any infringements of patents or other rights of third parties resulting from its use.
  • Page 3 10-01-2012 C (CAL TRANs) Released ptate 10-17-2012 Released Zsapp 12-21-2012 Released tbrennan 12-02-213 Released tbrennan 1-13-20013 AGPS Base Station 400A Base Station Document Name: 906-0003 AGPS Installation Manual Rev D.docx © Company 2014. All rights reserved. Page 3 of 15...

  • Page 4: Table Of Contents

    Campbell Company 906-0003 AGPS Installation Manual Rev D.docx Advisor Guide Pedestrian Signal [Version D] Table of Contents Introduction ......................5 ......................5 URPOSE OF THIS DOCUMENT ..........................5 DENTIFICATION ........................ 5 EFERENCE INFORMATION ......................... 5 OINTS OF ONTACT Installation Plan ...................... 6 .............................

  • Page 5: Introduction

     Reference information See AGPS Owner’s Manual for operational information   See AGPS Troubleshooting Manual Reference Campbell Company Intersection Worksheet for location information  Points of Contact  Customer Support, Queries, and Troubleshooting information Tony Brennan, Manufacturing Engineer 1.208.345.7459 tony@pedsafety.com...

  • Page 6: Installation Plan

    (See Owner’s Manual) Location Identify the location of the AGPS Base Station using the Intersection Worksheet provided with the installation packet. Pedestrian Stations are identified with the Campbell Company Work Order number and Station Identification number.

  • Page 7: Tasks

    Test and Adjust Fax checklist to Campbell Company Install Utility Application The AGPS Utility application provided by Campbell Company is required before installation: USB Configuration Utility Install the computer based configuration utility onto a portable computer. An electronic copy of the utility is available at www.pedsafety.com...

  • Page 8: Installation Procedure

    The tactile arrow is field selectable (left or right) requiring two security screws and a security driver. Campbell Company provides this hardware packet only when specified at the time of purchase. Contact Campbell Company Technical Support if a security bit is needed for tactile arrow modification.
  • Page 9 Campbell Company 906-0003 AGPS Installation Manual Rev D.docx Advisor Guide Pedestrian Signal [Version D] Mount the Pedestrian Station 1. Route the four conductor cable from the 1 1/8” hole through the pole into the pedestrian signal head for connection to the SPI.
  • Page 10 The tactile arrow is field selectable (left or right) requiring two security screws and a security driver. Campbell Company provides this hardware packet only when specified at the time of purchase. Contact Campbell Company Technical Support if a security bit is needed for tactile arrow modification.
  • Page 11 Campbell Company 906-0003 AGPS Installation Manual Rev D.docx Advisor Guide Pedestrian Signal [Version D] 3. Locate a tapped hole in close proximity to the 120 VAC three position barrier terminals (this may vary among manufactures) 4. Insert the ¼” - 20 x 1” FHP through the SPI housing and into the tap holes. Align the SPI horizontally such that the 120 VAC wires sag below the housing and attach to the three position barrier terminal;...
  • Page 12 Campbell Company 906-0003 AGPS Installation Manual Rev D.docx Advisor Guide Pedestrian Signal [Version D] 5. Attach the four conductor wires from the Base Station to the to the four position 12VDC barrier terminal on the SPI. (See Figure 3) Terminal 1: S1 DW ...

  • Page 13: Post Installation

    Campbell Company 906-0003 AGPS Installation Manual Rev D.docx Advisor Guide Pedestrian Signal [Version D] Post Installation Operational Check 1. The AGPS comes fully configured at the factory. When first powered up, an audible locator tone will be present. 2. Depress the push button and verify the red LED turns on with an audible message “Wait”.

  • Page 14: System Requirements

    Campbell Company 906-0003 AGPS Installation Manual Rev D.docx Advisor Guide Pedestrian Signal [Version D] System Requirements Software Requirements The following software is required to install this application: USB Configuration Utility A computer based USB configuration utility down load onto a portable computer. A USB connection is required for base station communications.

  • Page 15: Appendix A: Acronyms, Abbreviations & Definitions

    (EP) Intersection Map of street names and station locations provided with Intersection installation packet. Pedestrian Stations are identified with Campbell Worksheet Company Work order # and Station Identification number Signal Power...

This manual is also suitable for:

400a base station

Table of Contents