Hunter Set & Save 44155c Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Hunter Manuals
  4. Thermostat
  5. 44155C
  6. Installation and operation manual

Hunter Set & Save 44155c Installation And Operation Manual

Hide thumbs Also See for Set & Save 44155c:
Table of Contents

Advertisement

Quick Links

Form# 42708-01
20120210
©2012 Hunter Fan Co.
Set & $ave
Set & $ave
Set & $ave
Programmable Thermostat
operation manual
1
installation and
Models
44155
44157
c

Advertisement

Table of Contents
loading

Related Manuals for Hunter Set & Save 44155c

Summary of Contents for Hunter Set & Save 44155c

  • Page 1 Set & $ave Set & $ave Set & $ave Programmable Thermostat installation and operation manual Models 44155 44157 Form# 42708-01 20120210 ©2012 Hunter Fan Co.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Important Information........5 Tools ..............6 Uninstalling the Existing Unit ......7 Installing the Thermostat ....... 12 Installing the Wall Plate ......... 13 Connecting the Wires ........16 Attaching the Thermostat ......18 Settings ............22 Methods of Operation ........27 Manual Operation ..........
  • Page 4 Programmable Thermostat Programmable Thermostat Model 44155C Model 44155C Congratulations! Thank you for choosing a Hunter programmable thermostat. Your new Hunter thermostat will provide years of reliable service and year-round energy savings. Please read this manual before beginning installation and save this booklet for complete...

  • Page 5: Important Information

    IMPORTANT INFORMATION This thermostat is designed to work on the following heating and cooling systems: Gas – Standing Pilot Gas – Electronic Ignition Gas – Fired Boilers Gas – Milivolt Systems Oil – Fired Boilers Oil – Fired Furnace Electric Furnace Electric Air Conditioning Single Stage Heat Pump - No auxilary This thermostat is not designed for multi-stage heat...

  • Page 6: Tools

    TOOLS This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your new thermostat, you will need the following supplies: Flat-head screwdriver ..................Small Phillips-head screwdriver ..................Hammer ..................Electric drill and 3/16” bit ..................Two 1.5 Volt (AA) size alkaline batteries ..................

  • Page 7: Uninstalling The Existing Unit

    UNINSTALLING THE EXISTING UNIT NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ensure proper reconnection.
  • Page 9 1. Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. 2. Remove the existing thermostat cover to access the wires from the wall. (Some thermostats may have multiple covers, screws or other locking devices that must be removed or disengaged.)
  • Page 10 if your existing label the wire thermostat is marked... with this sticker: RH / R / VR / 4 24 Volt RC / VC 24 Volt cool air conditioning Y / C* / M / O compressor W / H / B heating G / F heat pump...
  • Page 11 4. Using the provided stickers, label each wire according to the chart. • If the terminals are not labeled, contact a qualified HVAC technician. • Note: Wire colors do not always comply with standards, so wire color should be ignored. Refer to the existing terminal designation for proper identification.

  • Page 12: Installing The Thermostat

    INSTALLING THE THERMOSTAT...

  • Page 13: Installing The Wall Plate

    3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes, visually level the wall plate and mark the wall for two holes.
  • Page 15 4. Remove the wall plate and drill two 3/16” holes where marked. 5. Tap the plastic anchors into the holes until they are flush with the wall. 6. Reposition the wall plate on the wall, pulling the wires through the opening. Insert the mounting screws through the wall plate and into the anchors.

  • Page 16: Connecting The Wires

    CONNECTING THE WIRES G RCRH Y/0 W/B Y1 Terminal Shield...
  • Page 17 1. Loosen, but do not remove, the terminal screws. Note: A jumper wire has been provided, connecting the RC and RH terminals for systems that do not provide both an RH and RC wire. If you have both an RH and RC wire, remove this jumper.

  • Page 18: Attaching The Thermostat

    ATTACHING THE THERMOSTAT Thermostat Cover HEAT ENABLE RECOVERY DISABLE System Switch SYSTEM TYPE FAN OPTION W/B Y/O RH RC G RH Y/O W/B Y1...
  • Page 19 SYSTEM switch Lift the thermostat cover and set the switch to AUTO. and the HE/HG switch 1. Locate the on the back of the thermostat. Set the switch to (default) for gas furnace and oil burners. Set the switch to for electric furnaces.
  • Page 21 4. Place the top of the thermostat over the two tabs on the wall plate. Press the thermostat onto the wall plate and press to snap the bottom tab into place. Note: Do not force the thermostat onto the wall plate, as the terminal pins may be damaged.

  • Page 22: Settings

    SETTINGS reset...
  • Page 23 The default setting of the thermostat is Fahrenheit (F NOTICE: CHANGING THIS SETTING WILL RESET THE THERMOSTAT TO FACTORY DEFAULT PROGRAMS. (If no button is pressed for 5 seconds, the unit will return to the Normal Display mode.) To change to Celcius (C 1.
  • Page 24 day/time...
  • Page 25 The default for this thermostat setting is in a 12 hour format. You can change the format to Day/Time 24 hour format by pressing and then Program. The AM/PM indicator will be off when the thermostat is in 24 hour mode. Setting day and time: Day/Time 1.
  • Page 26 HEAT...

  • Page 27: Methods Of Operation

    METHODS OF OPERATION This thermostat gives you the ability to program up to 4 custom temperature settings per day or utilize pre-programmed settings. For manual operation instructions, see pages 28-31. To utilize the pre-programmed settings, see pages 32-33. To create custom programs, see pages 34-37.

  • Page 28: Manual Operation

    MANUAL OPERATION HEAT...
  • Page 29 Many people prefer to operate their thermostats manually, adjusting settings as needed. You can either temporarily override the settings for the current program, or permanently override all settings and adjust temperatures manually. If you want to only override the current program: Down 1.
  • Page 30 HOLD system heat cool hold /return...
  • Page 31 If you want to permanently override all settings and adjust the thermostat manually: Hold/Return 1. Press until the Hold icon appears. Down 2. Press and hold for one second to enter Manual Override mode. (Release the button when the display flashes.) Down 3.

  • Page 32: Default Programs

    DEFAULT PROGRAMS 10 pm Program 4 Heat : 60 F (16 Cool : 82 F (28 Program 3 Heat : 68 F (20 Cool : 78 F (26 6 am Program 1 Heat : 68 F (20 Cool : 78 F (26 4 pm 8 am...
  • Page 33 By using the pre-programmed settings, this thermostat can save you money by optimizing energy usage in heating and cooling. After setting the time and temperature scale, no additional action is needed to utilize the pre- programmed settings. Refer to the Default Programs Chart for detailed information about the pre-programmed settings.

  • Page 34: Creating Custom Programs

    CREATING CUSTOM PROGRAMS system program heat cool hold /return...
  • Page 35 • Program times can be set in 10 minute increments. • Program temperature can be set in increments of 1 F (1 • After 15 seconds of inactivity during programming, the thermostat will return to Normal Display mode. • When setting the program time, note the AM/ PM indicator.
  • Page 36 M T W TH F HEAT COOL system program heat cool hold /return...
  • Page 37 Down 3. Press to change the hour. Press Program to save the hour and adjust the minute setting. Down 4. Press to change the minute. Press Program to save the minute setting and adjust the temperature. Down 5. Press to set the temperature. Program Press again to move to the next...

  • Page 38: Icons And Features

    ICONS AND FEATURES FILTER filter...
  • Page 39 ® 1. INDIGLO Night-Light - will backlight the display for easy viewing in the dark. Press any button to illuminate the light. (If no button is pressed after 5 seconds, the backlight will turn off.) Note: If the thermostat shows a Low Battery Warning, the backlight will not operate.
  • Page 40 HEAT COOL system heat cool reset...
  • Page 41 3. Span setting mode – allows you to adjust the system ON/OFF cycle rate. The default setting is 2 (the system cycles ON or OFF when the temperature is within 1 F (0.5 above and below the set temperature.) The span setting can be adjusted if your system is cycling too fast or too slowly.
  • Page 42 COOL STAGE 1 STAGE 2...
  • Page 43 4. Low battery warning – indicates two stages of battery power shortage. When the batteries are detected as weak, the icon will flash until new AA alkaline batteries are installed. If the batteries become too weak for normal operation, the thermostat enters the second battery power shortage mode.
  • Page 44 hold /return...
  • Page 45 5. Auto recovery – allows heating and cooling systems to gradually recover from an energy-saving setpoint temperature to a comfort setpoint temperature. Auto recovery calculates the time needed to adjust the temperature to the next program setting. When the thermostat is in Auto Recovery mode, the display will flash alternating messages of RECO and the time.
  • Page 47 6. Error mode – indicates an unexpected battery problem. The screen will flash an ERR message and shut your system off until the batteries are replaced with new AA alkaline batteries. You must Reset and reprogram the thermostat after replacing the batteries if the thermostat has entered Error mode.
  • Page 48 1. Temperature Range 99 o F 30 o F 45 o F 95 o F (37 o C) (7 o C) Out of Range Out of Range Program Range "LO" "HI" Display Range < 30 o F > 99 o F 2.

  • Page 49: Troubleshooting

    TROUBLESHOOTING 1. My display will not come on. • Check batteries and battery connections. • Reset the thermostat..................2. The auto fan feature will not operate properly. • Remove the thermostat from the wall plate and set the HG/ HE switch to the correct position.
  • Page 50 5. My heating or cooling will not turn on or off. 5 a. Check the Heat/Cool function switch to ensure it is set to the desired position. 5 b. Wait. There may be as much as a 4-minute delay before the system turns on or off to protect the compressor.
  • Page 51 7. My system continues to operate when the thermostat is in the off position. 7 a. Replace unit..................8. The LCD screen permanently reads HI, LO, or ERR. 8 a. Replace unit..................9. How do I just operate my thermostat manually? 9 a.
  • Page 52 Can I just call someone? Sure. Our Technical Support Group is available from 8 am to 5 pm CST. They may be reached toll-free at 1-888-830-1326. Click Here to Read More..Mobile friendly optimized manual: Hunter 44155c / 44157 Thermstat Installation and Operation Manual...

This manual is also suitable for:

Set & save 44157

Table of Contents