Advertisement
WiFi B- -SAM SETUP 1
AUX:
IP TYPE:
IP:
MAC ADDR:
SUBNET MASK:
SERVER
STATUS:
< BACK
AUX: The auxiliary sensor can be renamed to something meaningful, such as WATER or GENERATOR. Use the Temp +/- - buttons to move
between letters, and the Time +/- - button to choose letters.
IP TYPE: Choose DHCP (default) or STATIC for the Internet addressing type.
IP: Shows the current IP address of the SAM. If IP TYPE is STATIC then this item can be change. Use the Temp +/- - buttons to move
between letters, and the Time +/- - button to choose letters. If IP TYPE is DHCP, the IP address cannot be changed.
MAC ADDR: Shows the MAC Address of the SAM's network module.
SUBNET MASK: If IP TYPE is STATIC, this can be changed to a different subnet number. Use the Temp +/- - buttons to move between
letters, and the Time +/- - button to choose letters. If IP TYPE is DHCP, the SUBNET MASK cannot be changed.
DEFAULT GATEWAY: If IP TYPE is STATIC, this can be changed to point to a different gateway. Use the Temp +/- - buttons to move
between letters, and the Time +/- - button to choose letters. If IP TYPE is DHCP, the DEFAULT GATEWAY cannot be changed.
DNS SERVER: If IP TYPE is STATIC, this can be changed to point to a different DNS server. Use the Temp +/- - buttons to move between
letters, and the Time +/- - button to choose letters. If IP TYPE is DHCP, the DNS SERVER cannot be changed.
PORT: This can be changed to use a different port through the homeowner's network. The default is port 49152.
SERVER STATUS: Shows status of the SAM connection to Bryant's servers. If the screen shows NON CONNECTED, please check
network settings or network cable.
Pressing the right side button (for NEXT >) will display the following screen:
WiFi B- -SAM WIRELESS 1
SSID:
HOME
CHANNEL:
SIGNAL STRENGTH:
J J J j j j j j j
L
SERVER STATUS:
< BACK
SSID: Enter the name of the homeowner's wireless network using the Temp +/- - and Time +/- - buttons.
CHANNEL: This field determines which frequency to use. It can be left on Channel 0 to search automatically, or adjusted to the one being
used by the homeowner's wireless router.
ENCRYPTION: This chooses the type of security used by the homeowner's wireless router. Choose:
S None - - no data encryption
S WEP (Wired Equivalent Privacy) - - use WEP 64 or 128 bit data encryption
S WPA (WiFi Protected Access Pre- -Shared Key ) - - use WPA- -PSK standard encryption
KEY: WEP 64 BIT HEX (10 hex digits)
WEP 64 BIT CHARS (5 ASCII characters)
WEP 128 BIT HEX (26 hex digits)
WEP 128 BIT CHARS (13 ASCII characters)
WPA PSK HEX (8 to 64 hex digits)
WPA PSK CHARS (8 to 63 ASCII characters)
SIGNAL STRENGTH:
CONNECTED means the SAM has connected with the wireless router. NOT CONNECTED will mean either one of the parameters is
incorrect, or the signal strength may be too low.
E2008 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
AUX SENSOR
DHCP
192.168.100.0
00:01:02:03:04:05
255.255.255.000
CONNECTED
NEXT >
0
H
CONNECTED
NEXT >
Displays the current signal strength of the identified wireless router (SSID). Nine bars is full strength.
WiFi B- -SAM SETUP 2
DEFAULT GATEWAY:
DNS SERVER:
PORT:
SERVER
STATUS:
< BACK
WiFi B- -SAM WIRELESS 2
ENCRYPTION:
KEY:
ENTER 10 HEX DIGITS
< BACK
Printed in U.S.A.
Edition Date: 09/08
6
192.168.001.001
061.010.231.015
49152
CONNECTED
NEXT >
WEP 64 BIT HEX
0- -9, A- -F
NEXT >
Catalog No. IIBBRWF---01
Replaces: NEW
Advertisement
