Download Print this page

ManoMano 01SHPR0806RS-V1 Quick Start Manual

Advertisement

Quick Links

01SHPR0806RS-V1
Please retain product label and instructions for future reference
Dimensions
Length = 1779mm
Width = 2357mm
Height = 2231mm
Before
assembly make sure
you have a suitable
base ready to erect
your building
MADE IN GREAT BRITAIN
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be a ected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are delivered pre-treated with a water based timber treatment
however this only helps to protect during transit of your garden item. To
validate your guarantee and for better protection against weathering it is
ESSENTIAL that you treat the garden building with a wood preserver within 3
months of assembly. This will need to be re-applied annually to ensure longevity
of your building. Care must be taken when constructing the garden building
that it is not touching the ground and is on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be
slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also
recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71
level, we cannot accept responsibility for your safety whilst erecting or using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
01OVLR0806RS-V1
01636880514
x2
This building should be erected by
two adults
For ease of assembly, you must pilot
drill all screw holes and ensure all
screw heads are countersunk.
2mm Drill bit
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every e ort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
For Assistance Please
Contact Customer Care on
01636 880514
1
Plain Side x1
4
Floor x2
Fixing Kit
7
Ridge bar 2285mm Qty 1
8
Roof eave 1185mm Qty 4
9
Diamond Finial Qty 2
10
Corner trims 1740mm Qty 4
11
Fascias 1027mm Qty 4
12
Floor Joining blocks 400mm Qty 5
13
14
Pad bolt Qty
T-hinge Qty 3
1
18/10/2011
3
2
Door panel x1
Roof Sheet x2
5
6
Gables x2
Door x1
15
L brace Qty 2
16
Padbolt Block
17
120mm
Qty 1
Felt
18
Capping
Felt

Advertisement

loading

Summary of Contents for ManoMano 01SHPR0806RS-V1

  • Page 1 18/10/2011 01SHPR0806RS-V1 01OVLR0806RS-V1 Please retain product label and instructions for future reference 01636880514 Dimensions Length = 1779mm Width = 2357mm Height = 2231mm Plain Side x1 Door panel x1 Roof Sheet x2 Before assembly make sure you have a suitable...
  • Page 2 Nail Bag Step 3 Secure the plain gable to the 50mm Screw x35 plain panel with screws as shown in the diagram. Making sure to NOT SCREW the 40mm Screw x40 panels to the floor until the roof is on the 30mm Screw x90 building.
  • Page 3 Step 5 Step 7 Using 3x40mm screws per hinge fix the door to the door Secure the ridge bar panel making sure to screw using 2x L brackets into the framing and allow as shown in the gaps for the door to open and diagram, using close.
  • Page 4 Step 9 Step 10 Cut the felt into 2 sheets and apply to the roof along secure the floor to the base the outside edges, as using 4x40mm screws per shown, tacking the felt at panel, securing all 4 panels 100mm Intervals.
  • Page 5: After Treatment

    Step 11 Secure the corner trims as shown in the diagram on the front and back using 3x40mm screws per strip. 12 x 40mm screws Step 12 Secure the facias using 3x40mm screws per facia ensuring that the edges butt up in the middle.

This manual is also suitable for:

01ovlr0806rs-v1