Download
Share
Print this page
Cessna Swapping GIA 1 Manual
  1. Manuals
  2. Brands
  3. Cessna Manuals
  4. Aircrafts
  5. Swapping GIA 1
  6. Manual

Cessna Swapping GIA 1 Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Swapping GIA 1 & GIA 2 (GIA 63W) on Citation M2
Caution: Before starting the software or configuration loading process, certain
items may be required to be recorded first, to prevent loss of
information or settings. See Section 1 for details.
Caution: Make certain that all SD cards are available before starting. These are
usually located in a blue pouch onboard the aircraft (usually in AFM).
Caution: Follow all steps in a given section for specific loadings. Failure to do so
will result in probable rework.
Caution: Ensure that power is available through a GPU so that power is not
interrupted during the loading process.
Note:
This document is to supplement, not replace, the Cessna Citation M2
MM, and Garmin G3000 LMM.
Note:
Reference latest revision of the Garmin G3000 LMM 190-01668-00.
Introduction
Section 1
Section 2
Section 3
Section 4
Section 5
Appendix A
Version 1.0
Garmin G3000 Software Version 10
Table of Contents
G3000 System Familiarization
References Prior to Certain Software and Configuration Loading
Software and Configuration Loading
Reinstalling Options
Final Verification / Return to Service
Troubleshooting
Configuration ID / CRC Numbers
1

Advertisement

loading

Related Manuals for Cessna Swapping GIA 1

Summary of Contents for Cessna Swapping GIA 1

  • Page 1 Swapping GIA 1 & GIA 2 (GIA 63W) on Citation M2 Garmin G3000 Software Version 10 Caution: Before starting the software or configuration loading process, certain items may be required to be recorded first, to prevent loss of information or settings. See Section 1 for details.
  • Page 2 Introduction G3000 System Familiarization When in configuration mode, select GDU controls on left side of GTC 1. Ensure that PFD 1 is selected on the screen. The dual concentric knobs on the lower right bezel will be utilized, and throughout this document will be referred to as the FMS small and large knob. The Enter button will be in the lower right part of the screen.
  • Page 3 Section 1 References Prior to Certain Software and Configuration Loading When swapping GIA 63W from side to side the following steps must be completed first: Note: This is with the G3000 powered up in normal mode. Caution: If any optional radio appears to have an amber X and is grayed out as in this example, then the LRU is not installed, but was previously loaded incorrectly.
  • Page 4 • GDL69 o From the Home screen of either GTC 570, touch the Weather button. Then touch Weather Selection. The option is installed if Sirius XM Settings is displayed. • Becker ADF o ADF controls are seen on the AUDIO & RADIO screen of either GTC 570. •...
  • Page 5 • GSR56 Weather o From the Home screen of either GTC 570, touch the Weather button. Then touch Weather Selection. The option is installed if CONNEXT WEATHER is displayed. Should be if a single or dual GSR 56 is installed. •...
  • Page 6 • TCAS II o From the Home screen of either GTC 570, select the transponder button in the upper right part of the screen. TCAS II option is loaded if there are 5 buttons on the left side of the screen. Otherwise, TCAS I is loaded. Also, there should be an unlock SD card present.
  • Page 7 • CPDLC o The CPDLC button is available on the home screen of either GTC. Also, there should be an unlock SD card present. Radar Trim Settings • Go into the left GTC: o Use Back button and select Aircraft Systems. o Select Maintenance.
  • Page 8 Section 2 Software and Configuration Loading This section will provide the steps necessary to target load the software and configuration into GIA 1 & GIA 2 after swapping. Note: Anytime that software or configurations are being loaded, all three displays, and both touch controllers must be in configuration mode.
  • Page 9 6) Press and hold the #12 softkey on the #2 PFD and push the R PFD circuit breaker  Let go when you see initializing.  PFD 2 should come up in configuration mode. • SYSTEM STATUS should show at the top of the screen. 7) Press and hold the #12 softkey on the MFD and push the MFD circuit breaker in.
  • Page 10 2) Rotate the small knob to drop the menu down, and highlight ‘525 Base Configuration’ in the GROUP field. 3) Press the Enter key. 4) Rotate the small knob to drop the menu down, and highlight ‘Cessna Model 525 Base Configuration’ in the ITEM field. 5) Press the Enter key.
  • Page 11 15) Acknowledge when ‘Upload and Crossfill Complete’ is displayed by pressing the Enter key. 16) Push the UPDT CFG softkey to update the system configuration files. 17) Select YES, and press the Enter key. 18) Acknowledge when ‘Update Config Complete’ is displayed by pressing the Enter key.

  • Page 12: Gdl

    Section 3 Reinstalling Options This section will provide the steps necessary to reload the options that were originally installed. CAUTION: Only load the options determined to be installed in Section 1. • Single GSR56 Option: 1) Rotate the large knob to the left until in the GROUP field. 2) Rotate the small knob to drop the menu down, and highlight ‘Options’...
  • Page 13  System  Manifest  GDL 59  GDL 59 Router  GDL 59 Router File System 7) Select the LOAD softkey at the bottom of the display. 8) Monitor the configuration load to verify the green PASS message next to each item.

  • Page 14: Gdr

     GIA63W 1 Config 7) Select the LOAD softkey at the bottom of the display. 8) Monitor the configuration load to verify the green PASS message next to each item. 9) Press the Enter key when all the loading is complete to acknowledge the upload is complete window.

  • Page 15: Cabin Briefing H

    7) Select the LOAD softkey at the bottom of the display. 8) Monitor the configuration load to verify the green PASS message next to each item. 9) Press the Enter key when all the loading is complete to acknowledge the upload is complete window.

  • Page 16: Dme

    • DME 2 Option: 1) Rotate the large knob to the left until in the GROUP field. 2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the GROUP field. 3) Press the Enter key. 4) Rotate the small knob to drop the menu down, and highlight ‘DME 2 Option’ in the ITEM field.

  • Page 17: Taws Class A P

    13) Select the LOAD softkey at the bottom of the display. 14) Monitor the configuration load to verify the green PASS message next to each item. 15) Press the Enter key when all the loading is complete to acknowledge the upload is complete window.
  • Page 18 6) PFD 1 should be on the system upload page. 7) Activate the cursor by pushing down on the FMS knob. 8) Rotate the small knob to drop the menu down, and highlight ‘TCASII Enablement’ in the GROUP field. 9) Press the Enter key. 10) Rotate the small knob to drop the menu down, and highlight ‘GTS TCAS II Enablement’...

  • Page 19: Doppler & Turbulence T

    16) Pull L PFD circuit breaker and remove the 010-00330-C7 Windshear Unlock card from the upper slot of PFD 1. • Doppler & Turbulence: 1) Pull the L PFD circuit breaker (if not already done). 2) Remove the 010-01121-10 software loader card from the upper slot of PFD 1 if installed.
  • Page 20 9) Press the Enter key. 10) Rotate the small knob to drop the menu down, and highlight ‘FK677A-VHF DataLink (CPDLC/Link 2000+)’ in the ITEM field. 11) Press the Enter key. 12) All boxes should be checked. 13) Select the LOAD softkey at the bottom of the display. 14) Monitor the configuration load to verify the green PASS message next to each item.
  • Page 21 Section 4 Final Verification / Return to Service Note: This is with the G3000 powered up in normal mode. • Select Home on the left GTC controller. o Select Utilities. o Select Setup. o Select Avionics Status. o Select the Airframe tab on the left side. o Verify that the configuration ID (CRC Number) matches the number determined in Appendix A based on the options installed in the aircraft.
  • Page 22 Section 5 Troubleshooting This section will provide corrective actions for issues seen after the software is loaded. Substitute LRU name for ***. • *** DB Error or *** DB Mismatch o Ensure that the supplemental SD cards are installed in the lower slots of the displays.

  • Page 23: Table Of Contents

    Appendix A Configuration ID / CRC Numbers This section will provide details on determining the correct configuration ID or CRC number for a particular M2 aircraft based on the installed options. Through the rest of this section the number will be referred to as a CRC number for simplification. Note: Radar trims that are not at zero for both pitch and roll will cause the number to be different.
  • Page 24 Option CRC Number Option CRC Number Option CRC Number 8D808EC9 ACKM 002A20B9 705A67B6 ACEF 461C7003 ACKMNPRST BFB15610 CFNP D6F7CAC3 ACEFK 461D07AD ACKMNPST 56B80596 CFNPT 03F4DB35 ACEFKN DC136899 ACKMP 66C783C6 CFNPTV 7F37E14C ACEFKNPR ABAA1C20 ACKMPS 93C49438 CFNRS 0650C8A2 ACEFKNPV C5F4177B ACKMPST COC1A4AA CFNRV 5496BE47...

This manual is also suitable for:

Swapping gia 2