Advertisement
Bullard TI Commander™ Thermal Imager
Congratulations
Congratulations on the purchase of your new Bullard TI
Commander Thermal Imager. The Bullard TI Commander
combines advanced thermal imaging performance and
unsurpassed firefighting features with Bullard's expertise
in high heat, impact resistant thermoplastics. Its
innovative design, extensive feature set, and legendary
durability make the Bullard TI Commander the best choice
for firefighters who demand maximum performance and
flexibility.
The benefits of using thermal imaging technology as a
firefighting tool encompass just about every aspect of a
firefighter's job. Thermal imaging is not, however, a
technology designed to replace current firefighting tactics.
Rather, it is a tool that allows the firefighter to be more
effective and make better decisions. Some of the many
uses for your Bullard Thermal Imager include:
• Search and rescue
• Scene assessment
• Locating the seat of the fire
• Determining the spread of the fire
• Locating hot spots
• Identifying potential flashover situations
• Determining ventilation points
• Determining entry and exit points
• Overhaul
• Hazmat
• Wildland firefighting
• Incident Investigation
• Training
NOTE
To ensure that we are able to reach you
with any product or software updates,
please fill out the warranty card enclosed
with your Bullard TI Commander Thermal
Imager.
WARNING
Read all instructions and warnings before using this
product. Failure to observe this information could result
in death or serious injury.
Table of Contents
Imager Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Use and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . .4
Palm and Top Straps . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Care Instructions/Replacing Display Cover . . . . . . . 6
Service/Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . 8
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bullard TI Commander
Summary of Contents for Bullard TI Commander
- Page 1 Bullard’s expertise in high heat, impact resistant thermoplastics. Its innovative design, extensive feature set, and legendary durability make the Bullard TI Commander the best choice for firefighters who demand maximum performance and flexibility. The benefits of using thermal imaging technology as a firefighting tool encompass just about every aspect of a firefighter’s job.
- Page 2 Bullard TI Commander Thermal Imager Rear Boot Top Strap (12) Polycarbonate Display Cover (9) Image Capture (4) (Optional) Palm Strap (13) LCD Screen Lens Bezel (8) Lens Battery Compartment (7) 2X Digital Zoom (5) Relative Heat Indicator™ (6) (Optional) (Optional)
- Page 3 Power unit (Item 2, Figure 1). Turning the dial clockwise To turn on the Bullard TI Commander, depress the large red (toward the lens) closes the Thermal Throttle, turning it “On/Off” button (Item 1, Figure 1) on the left side of the counterclockwise opens the Thermal Throttle.
- Page 4 The direct charge system will allow the battery of the The amount of drain varies widely based on storage Bullard TI Commander to be charged inside the camera. conditions. For best performance, charge each of the The standard battery charger should be connected to a batteries every two weeks.
- Page 5 The right bracket should then be secured by placing the bracket on the screw and tightening the nut. The strap is correctly attached when the Bullard logo or custom lettering is facing outward. Wrist Strap Adjusting the Palm Strap To adjust the palm strap on the side of the unit, pull open the leather hand guard and readjust the strap.
- Page 6 Care Instructions Cleaning the Lens The Bullard TI lens is protected by both a silicone gasket The design of the Bullard TI Commander requires ongoing, and a plastic lens bezel. The bezel (Item 8, Figure 1) but relatively simple maintenance. For best results,...
- Page 7 4. When the outer shell is obsolete and Bullard no longer stocks distributor for the amount of the estimate. Once Bullard the part, the limited lifetime warranty will be terminated.
- Page 8 TI Commander Startup Custom Graphics Option – customer supplied CMDUPGRADE Upgrades a TIx model to a TI Commander – includes 5 inch display and custom text, logo, or other graphics that appear on display during upgraded direct charge port and cable. Can be equipped with optional startup features.
Need help?
Do you have a question about the TI Commander and is the answer not in the manual?
Questions and answers