LogTag Recorders TRID30-7 Product User Manual
Temperature recorder with display and 30 day statistics memory
Hide thumbs
Also See for TRID30-7:
- User manual (7 pages) ,
- Quick start manual (2 pages) ,
- Quick start manual (2 pages)
Related Manuals for LogTag Recorders TRID30-7
Summary of Contents for LogTag Recorders TRID30-7
- Page 1 LogTag Recorders Ltd TRID30-7 Temperature Recorder with Display and 30 Day Statistics Memory Product User Guide Document Release Version: 1.3 Published 1 September 2016 ® Copyright © LogTag Recorders , 2004-2016...
-
Page 2: Table Of Contents
-Update Time/date starting feature. -Added optional display of days collected while recording. 16/06/2016 Stefan Lenz Trial with new display layout 1/9/2016 Stefan Lenz General Update ® Page 2 of 16 TRID30-7 Product User Guide, Revision 1.3, copyright © 2004-2016, LogTag Recorders . All rights reserved. -
Page 3: Safety Information
… the device is stored and operated according to LogTag ® Recorders ’ recommendations. Disclaimer The TRID30-7 monitors temperature exposure and not the quality of the goods it accompanies. Its purpose is to signal if product quality evaluation/testing is required. Typographical Conventions Text refers to buttons on the TRID30-7. -
Page 4: Introduction
Configuring the TRID30-7 Features Before a TRID30-7 recorder can be used, it must be configured with the parameters required for starting and recording temperature The TRID30-7 temperature recorder features the familiar LogTag case ®... -
Page 5: Standard Configuration Options
Begin recording after a delay. midnight, then it turns off and the marker for the previous day is If you configure the TRID30-7 to start after a delay period, the shown to indicate the alarm was registered against what is recorder will not immediately record temperature readings after now the previous day. -
Page 6: Advanced Configuration Options
/CLEAR/STOP Enter the desired options and click to accept the new values. This returns you to the standard configuration dialogue. ® Page 6 of 16 TRID30-7 Product User Guide, Revision 1.3, copyright © 2004-2016, LogTag Recorders . All rights reserved. -
Page 7: Display Overview
CURRE NT This 4 character, 7-segment display shows the last recorded represents the last recorded temperature. temperature while the TRID30-7 is recording . Once the recorder has The word is shown in Review mode, when the temperature on stopped, nothing will be displayed. -
Page 8: Real Time Clock
Accept the minutes value by pressing . The hours value now flashes. ® Page 8 of 16 TRID30-7 Product User Guide, Revision 1.3, copyright © 2004-2016, LogTag Recorders . All rights reserved. -
Page 9: Starting The Recorder
STOPPED Automatic date/time start If the button is released earlier than 6 seconds or later than 6 seconds, If you configured the TRID30-7 for a date/time start, it will start the display shows again, and the recorder does not start. -
Page 10: During Recording
Marking a reading with an inspection mark During Recording When you press the button, the next reading taken by the TRID30-7 During normal operation the display shows the most recently recorded will be identified in the downloaded data with an inspection mark. -
Page 11: Power Save
CURRENT RECORDING PAUSED Figure 7: TRID30-7 stopped, showing ‘27’ days of data has been collected. Note, this is not always the number of days the recorder has collected Paused readings are specially marked in the graph and data listings. data. Depending on the sampling interval the recorder can hold more ®... -
Page 12: Reviewing Day Statistics On The Trid30-7
Yesterday, no temperature values were recorded below the lower that yesterday's data is being displayed. alarm threshold, and no alarm event was generated . ® Page 12 of 16 TRID30-7 Product User Guide, Revision 1.3, copyright © 2004-2016, LogTag Recorders . All rights reserved. -
Page 13: Stopping The Trid30-7
RECORDING PAUSED Manually You can configure a TRID30-7 so it can be stopped with the button. This feature is useful when you take the START /CLEAR/STOP recorder out of a shipment and don’t want to falsify the statistics with... -
Page 14: Resetting The Recorder
Analyzer by clicking Hibernate on the LogTag menu. The disply shows SLEEP for a few seconds, before turning itself off. ® Page 14 of 16 TRID30-7 Product User Guide, Revision 1.3, copyright © 2004-2016, LogTag Recorders . All rights reserved. -
Page 15: Technical Specifications
Values above 199.9°F cannot be shown on the display. The values will, however, be ® recorded and shown in the LogTag Analyzer software ® Page 15 of 16 TRID30-7 Product User Guide, Revision 1.3, copyright © 2004-2016, LogTag Recorders . All rights reserved. -
Page 16: Appendix 1 - Battery Replacement
Re-configure the recorder with LogTag Analyzer. Please recycle or dispose of the old battery according to your local environmental regulations. ® Page 16 of 16 TRID30-7 Product User Guide, Revision 1.3, copyright © 2004-2016, LogTag Recorders . All rights reserved.