Related Manuals for SignWarehouse enduraPRESS CS15AR TS
Summary of Contents for SignWarehouse enduraPRESS CS15AR TS
- Page 1 CS15AR TS USER MANUAL REV 04/06/2021 www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us...
-
Page 2: Table Of Contents
Specifications Operation Instructions Read Before Use Control Panel Operations Temperature display calibration Installing The Twins Shuttle Tables Heat Transfer Application Guidelines Troubleshooting Tips Wiring Schematic www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us... -
Page 3: Specifications
Control Panel: LCD Control Panel Time Range: 0~999sec. Temp. Range: 0~480°F Packaging: Double-walled Corrugated Paper Carton (This product is shipped in two boxes) Gross Weight: 127lbs (58kg) www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us... -
Page 4: Operation Instructions Read Before Use
7. Do not set the temperature any higher than 480F as it may cause over heat and stop working. 8. The heat press carries a ground line by default, please make sure the socket gets a ground line protector. www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us... -
Page 5: Control Panel Operations
Long hold the CLEAR button to clear start to cool down if heat press is your counter on the panel. inactive To reheat the press, hit any button www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us... -
Page 6: Temperature Display Calibration
Say 30 (i.e. heating platen 260°F, and the press will cool down 30°F hotter than the gauge read- to 230°F. out) www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us... -
Page 7: Installing The Twins Shuttle Tables
4)Tighten the screws holding the twin shuttle tables in FIG 2: Place the shuttle. Slightly tighten the screws the CS15AR base. in the middle FIG 3: Place the lower platens and tighten. www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us... -
Page 8: Heat Transfer Application Guidelines
** The EnduraPRESS CS15, CS15-AR, CS16, and CS16-AR are not recommended for use with two-step laser transfer papers. For these demanding applications, we recommend the EnduraPRESS SA12 or SD20. www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us... -
Page 9: Troubleshooting Tips
Pressure: If the temperature is correct, adjust the pressure. Some films require more pressure to bond the adhesive to the fabric. There should be some resistance when you close the press. If you have verified all of these and the film doesn’t stick, contact SIGNWarehouse customer service or Technical Support for further assistance. -
Page 10: Wiring Schematic
Thank you for choosing our products, you are entitled to one year free warranty service for our products. All exceeds warranty period we will still provide technical supports and maintenance guidance. www.signwarehouse.com • SignWarehouse, Inc. • 2614 Texoma Drive, Denison, TX 75020 • support@signwarehouse.com • signwarehouse.com/pages/contact-us...
Need help?
Do you have a question about the enduraPRESS CS15AR TS and is the answer not in the manual?
Questions and answers