OPTEX FA Z Series Instruction Manual

Photoelectric Sensor
Z3 SERIES
• Z3T-2500 □□ • Z3R- Q200 □□
• Z3R- 400 □□ • Z3D- L09 □□
• Z3D- 100 □□
INSTRUCTION MANUAL
● l Please confirm if specifications fulfill your needs.
● l Please read this manual carefully before the use and keep this for
future reference.
Safety Precautions
●It is dangerous to wire or attach/remove the connector
with the power on. Make sure to turn off the power before
operation.
●Make sure to use the product with the protective cover
attached and closed.
●Installing in the following places may result in malfunction:
1. A dusty or steamy place
2. A place generating corrosive gas
3. A place directly receiving scattering water or oil.
4. A place suff ered from heavy vibration or impact.
●The product is not designed for outdoor use.
●Do not use the sensor in transient state after power on
(approx. 100 ms).
●Do not wire with the high voltage cable or the power line.
Failure to do this will cause malfunction by induction or
damage.
●The sensor performance or digital display values may
depend on the individual units or the condition of detected
product.
●This product is not an explosion-proof construction.
Do not use the product under fl ammable, explosive
gas or liquid environment.
● Do not use the product in water.
● Do not disassemble, repair, or convert the product.
Failure to do this may cause failure, fi re, or electric shock.
● Operate within the rated range.
This product cannot be used as a safety device
to protect human body.
DIMENSIONS
Brackets for installation are optional and not included in this kit.
(Not standard accessory and please purchase if needed.)
Output indicator （orange）
Stable indicator （green）
Sensitivity adjuster L/ON , D/ON selector
Cable type : When using brackets of BEF-W100-B (option)
Optical axis
(Sender,Receiver)
Through beam sender ・
2-M3 P0.5
Receiver
Retro Coax. Receiver
Sender
Connector type : When using brackets of BEF-W100-A (option)
11
14
8.2
4.4
Optical axis
(Sender,Receiver)
3
13.7
SPECIFICATION
Cable type
Connector type
Nominal distance
Light Source
Spot size
Supply voltage
Current consumption
Response time
Control output
Operation mode
Sensitivity adjustment
Indicator
Ambient temp. ／ humidity
Storage temp. ／ humidity
protection category/material
*1 Sensing distance showed in above table is typical value in each type.
・
・
・
INPUT AND OUTPUT CIRCUIT DIAGRAM
NPN type
Protection
Protection
PNP type
Protection
Protection
Output indicator （orange）
Stable indicator （green）
Sensitivity adjuster L/ON , D/ON selector
φ 3.8 2m Cable
φ 3.8 2m Cable
出力表示灯 （橙）
BEF-W100-B
2-M3 P0.5
安定表示灯 （緑）
感度調整ボリウム
ライトON/ダークON切替スイッチ
29.3
20
Through beam sender ・
Receiver
2-M3 P0.5
Retro coax, receiver
M8 3/4-pin connector
Sender
Through Retro ref.
Z3T-2500(N/P) Z3R-400(N/P)
Z3T-2500C(N4/P4) Z3R-400C(N4/P4) Z3D-100C(N4/P4) Z3R-Q200C(N4/P4) Z3D-L09C(N4/P4)
*1
25m 0.01~4m
φ 1800㎜ /25 ｍ φ 280㎜ /4 ｍ
Sender : 20mA max
20mA max
Receiver : 15mA max.
NPN/PNP Open collector 100mA max. / DC30V max. (Residual voltage 1.8V max.)
Output indicator (orange LED) / Stable indicator (green LED)
-25 ～ 55℃ /35 ～ 85%RH （No condensation or freezing）
Protection
-40 ～ 70℃ /35 ～ 95%RH （No condensation or freezing）
Brown
①DC10 ～ 30V
Retro ref. / Transparent objects types ： Reflector V-61(option)
Load
Diffused ref. type ： Whtie plate 200x200mm
circuit
Black
④Control output
Protection
Limited range type ： White plate 100x100mm
Protection
Blue
③0V
Through beam emitter
Brown
①DC10 ～ 30V
Brown
Protection
①DC10 ～ 30V
Black
Brown
①DC10 ～ 30V ④Control output
Load
Load
circuit
Black
Load ④Control output
circuit
Blue
circuit
Black ③0V
④Control output
Blue
③0V
Blue
③0V
Connector pin No.
Brown
①DC10 ～ 30V
Brown M8 3pin
①DC10 ～ 30V
Brown
①DC10 ～ 30V
Black
④Control output
1
Blue Black
④Control output
Load
③0V
circuit
Blue
Load
③0V
circuit
Blue
③0V
Brown
①DC10 ～ 30V
Brown
Adjusting the potentiometer
①DC10 ～ 30V M8 3pin
M8 3pin
4
A
A 4
A 1 3
Blue
① 1 3
Blue ③0V
③0V
B
B
B
②
C C
C
A B B
A
B
③ A
Reflectors（option）
For Retro Reflective use only
Please confirm appropriate type considering sensing distance and conditions to use.
Reflectors are optional and not included in this kit.
(Not standard accessory and please purchase if needed.)
Standard Type Type：V-61
●
Sensing distance：0.01~4m(Retro Reflective Type）
1.2
BEF-W100-B
BEF-W100-A
Diffused ref. Transparent objects
Z3D-100(N/P) Z3R-Q200(N/P)
0~1m 0.01~2m
Red LED
φ 75㎜ /1200㎜ φ 140㎜ /2 ｍ
DC10 ～ 30V Including ripple (P-P) 10%
25mA max
500µs max
Light ON, Dark ON Selectable by switch
Brown
1 turn volume
①DC10 ～ 30V
Load
circuit
Black
④Control output
Blue
③0V
IP67 / Case : ABS , Front Cover : PMMA
Brown
①DC10 ～ 30V
Black
④Control output
Load
circuit
Blue
③0V Attachment
•
Tightening torque need to be under 0.5N•m.
• Use M3 screw to mount.
Brown
①DC10 ～ 30V
M8 3pin
4
1 3
Blue
③0V
M8 4pin
4 4
3 1 3
①・・・DC10~30V
③・・・0V
④・・・Control output
M8 4pin
M8 4pin
4
4
Set the detectable object at the detection position and turn the potentiometer
3
1
3
1
from MIN toward MAX until the output indicator(orange) light up. Call it
position A.
Remove detectable object and turn the potentiometer from MAX toward MIN
position where the output indicator(orange) is extinguished. Call it position B.
Point C midway between A and B is the optimum sensitivity position. The
position A and B may reverse by types and detecting situation .
Small reflector Type：V-42
●
Sensing distance：0.01~2.4m(Retro Reflective Type）
51.6
47
2- n 3.6
20 3
40 8.6
Small reflector Type：P-45A
●
Sensing distance：0.01~1.4m(Retro Reflective Type）
600-8815 Kyoto, Shimogyo, Awata Chudoji 91, Japan
TEL : +81-(0)75-325-2920
FAX: +81-(0)75-325-2921
Website : http://www.optex-fa.com
Limited range
Z3D-L09(N/P)
10~90mm
φ 8㎜ /90㎜
20mA max
M8 4pin
4
3
1
35
31
25 3.5
8
6.2
12.4
8.4 2.2