IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 1. Read all instructions. 13. Keep hands and utensils, other than the 2.
Page 3
23. CAUTION: In order to avoid a hazard due 25. In manual mode do not exceed normal to inadvertent resetting of the thermal operating cycle of 2 minutes on and 1 cut-out, this appliance must not be minute OFF . In smoothie mode, allow supplied through an external switching appliance to cool for 2 minutes between device, such as a timer, or connected to...
Parts and Features Before first use: After unpacking the Blender, follow the instructions in “Cleaning Your Blender.” Emulsion Cup Tamper Blender Cutting Blade Assembly Jar Pad RESET/OFF (Power) (I/ ) Switch Base START/STOP ) Button PULSE ( ) Switch Program Buttons Variable Speed Dial...
Page 5
Emulsion Cup: The Emulsion Cup helps create dressings and sauces that require slowly adding liquid ingredients into the Blender Jar while the Blender is in operation. Lid: The Lid is easy to put on, take off, and clean. Always use the Lid and the Emulsion Cup when the machine is in operation.
Using Your Blender Before first use: After unpacking the Blender, follow the instructions in “Care and Cleaning.” IMPORTANT: The Blender Jar and Cutting Blade Assembly are subject to wear during normal use. Always inspect Jar for nicks, chips, or cracks. Always inspect Cutting Blade Assembly for broken, cracked, or loose blades.
Page 7
How to Open Blender Lid IMPORTANT: To remove the Lid, use your finger to pull up on the front tab. Do not twist the Lid to take it off the Jar — this might harm the Lid material and prevent it from sealing the Blender Jar.
Page 8
Using Program Settings Programs are optimized for recipe categories and vary in blending speed and duration. Pressing a Program Button illuminates only the program selected. The Blender automatically starts when the Program Button is pressed and automatically stops at the end of the program. To stop Blender before program cycle ends, press START/STOP ( ) Button or the Program Button.
Using Manual Mode 1. Rotate the VARIABLE SPEED DIAL to 2. Press START/STOP ( ) and slowly leftmost. rotate the VARIABLE SPEED DIAL to the right or left during blending to increase or decrease blending speed. When pressing PULSE ( ), the Blender will run at selected speed until the PULSE ( ) Button is released.
Page 10
Using Manual Mode (cont.) 4. At the end of the blending cycle, 5. Remove Blender Jar. rotate the VARIABLE SPEED DIAL back to the leftmost position and w WARNING Burn Hazard. press the START/STOP ( ) Button to stop blending. Turn off the Blender Metal parts under with the RESET/OFF (I/ ) Switch on blending Jar get hot...
Blender and Accessory Tips Blender Tips • To add foods when Blender is operating, • Cutting large whole fruits and remove Emulsion Cup and add vegetables may allow them to blend ingredients through the opening. more quickly. • For best performance, the minimum •...
Care and Cleaning 1. Unplug Blender. 2. Remove Jar, Lid, and Emulsion Cup. Electrical Shock Hazard. w WARNING Disconnect power before cleaning. Do not immerse cord, plug, base, or motor in water or other liquid. w WARNING Burn Hazard. Metal parts under blending Jar get hot after extended use.
Troubleshooting Error Messages All Program Buttons are flashing. • The motor has overheated during use. Turn RESET/OFF (I/ ) (Power) Switch to OFF ( ) and allow to cool for 15 minutes. Flip RESET/OFF (I/ ) (Power) Switch to RESET (I), and resume normal operation.
Page 14
Troubleshooting (cont.) Blender fails to start and Program Lights are not illuminated. • Make sure that the main power RESET/OFF (I/ ) Switch is in the RESET (I) position. • Check to see if unit is securely plugged into an electrical outlet of the proper voltage and frequency.
Page 30
Name and content of hazardous substances in product (hazardous substance) Polybrominate Polybrominated Mercury Cadmium Hexavalent Chromium (Component name) Lead d biphenyls diphenyl ethers (Hg) (Cd) (Cr(VI)) (Pb) (PBB) (PBDE) (START/STOP Switch) (Power Switch) (MOTOR) (Power PCBA) (Button PCBA) (Timing PCBA) SJ/T 11364 This table is prepared in accordance with the provisions of SJ/T 11364.
Need help?
Do you have a question about the 58912-CN and is the answer not in the manual?
Questions and answers