Table of Contents
Advertisement
Quick Links
INTENDED USE OF THE M2008 SENSOR IS TO MEASURE THE AMOUNT OF LIQUID PROPANE INSIDE A PROPANE
TANK MEETING THE SPECIFATIONS BELOW, UNDER THE CONDITIONS LISTED BELOW.
USE OF THIS DEVICE IN A MANNER OTHER THAN STATED IN THIS MANUAL, MAY RESULT IN IMPAIRMENT OF
THE DESIGNED SAFETY PROTECTION AND THUS AN UNSAFE CONDITION.
MEASUREMENT METHOD
FLUID
TANK TYPES
TANK SIZES
Envelope Dimensions
Mounting location
Suitable for these locations
OPERATING TEMPERATURE RANGE
TEMPERATURE CODE
BATTERY
HUMIDITY RANGE
MAX ALTITUDE
AMBIENT CONDITIONS FOR TESTING
THIS DEVICE IS NOT TO BE REPAIRED OR OTHERWISE MODIFIED.
MAILING ADDRESS: 445 FM 1983, COLORADO CITY, TX 79512
Mopeka Products LLC
Manuel & Operating Instructions
Standard Sensor Models M2008 (Propane)
THIS DEVICE IS INTENDED FOR OUTDOOR USE ONLY.
WARNING
SPECIFICATIONS
Ultrasonic
Propane
Steel Tanks
Note: Also works with aluminum tanks with alternate mounting.
Not intended for use on composite cylinders.
Vertical DOT Cylinders of 20 -100 lb (5 - 25 gal)
Horizontal tanks up to 11' diameter
97 x 61 x 17.2 mm (3.8 x 2.4 x 0.68 in)
Tank Bottom
CLASS 1, DIVISION 2, GROUP D
CLASS 1, ZONE 2, GROUP IIA
-40° TO 60°C
T6
2 AA (non replaceable)
0 - 100%
4000m
23°C, 14.7 PSIA
WARNING
MOPEKA PRODUCTS LLC
www.mopeka.com
support@mopeka.com
www.mopeka.com
M2000003A
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MOPEKA Standard Sensor
Summary of Contents for MOPEKA Standard Sensor
- Page 1 Manuel & Operating Instructions Standard Sensor Models M2008 (Propane) INTENDED USE OF THE M2008 SENSOR IS TO MEASURE THE AMOUNT OF LIQUID PROPANE INSIDE A PROPANE TANK MEETING THE SPECIFATIONS BELOW, UNDER THE CONDITIONS LISTED BELOW. THIS DEVICE IS INTENDED FOR OUTDOOR USE ONLY.
- Page 2 The battery in this device is permanent and is not to be changed or tampered with. Do not use device for any other application, other environment, or in any other manner than as stated in this manual. Any such misuse may result in an unsafe condition. Mopeka Products LLC www.mopeka.com M2000003A...
- Page 3 1. Go to your app store. Search for Mopeka Tank Check app and install. ✓ 2. Launch the app. When it starts it will automatically start a search for Mopeka sensors. 3. Press and hold SYNC button until sensor appears on app. (up to 10 seconds) Mopeka Products LLC www.mopeka.com...
- Page 4 4. The sensor will then appear on your app as a new device. 5. Sensor is now Sync’d . You may now proceed to installing the sensor on the tank. Mopeka Products LLC www.mopeka.com M2000003A...
- Page 5 It is important to place it on the center of tank so that sensor is horizontal, or sensor reading quality can be poor. After a few seconds, up to a few minutes, the the readings will stabilize. Mopeka Products LLC www.mopeka.com...
- Page 6 Mopeka Products LLC www.mopeka.com M2000003A...
- Page 7 REVISION TABLE REVISION DESCRIPTION DATE RELEASE 2019.09.19 Mopeka Products LLC www.mopeka.com M2000003A...
- Page 8 Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Need help?
Do you have a question about the Standard Sensor and is the answer not in the manual?
Questions and answers
I have two 20 lb propane tanks with standard sensors. I replaced the 2 old sensors with new ones and reset my app so I get the correct readings. I can’t get my remote tank sensor to work. Any suggestions. It was working right before I replaced the sensors on the tanks
1. Verify Proper Installation – Ensure the sensor is correctly mounted on the bottom of the propane tank.
2. Check Sync Status – Open the Mopeka Tank Check app and confirm the sensor appears in the app. If not, press and hold the SYNC button for up to 10 seconds to re-sync.
3. Ensure Compatibility – Confirm the tank is a steel or aluminum tank (with alternate mounting) and not a composite cylinder, as the sensor is not intended for composite tanks.
4. Inspect Battery – The sensor has a permanent, non-replaceable battery. If the battery is depleted, the sensor may no longer function.
5. Environmental Conditions – Ensure the sensor is used outdoors and within the operating temperature range of -40°C to 60°C.
6. Check for Interference – Reduce interference by increasing the distance from other electronic devices or relocating the receiving antenna.
7. Reinstall the Sensor – Remove the sensor, reposition it, and reinstall it on the tank to ensure proper contact.
8. Consult Support – If the issue persists, contact Mopeka support for further assistance.
This answer is automatically generated